On Sat, May 25, 2019 at 11:48 AM Frank Lee <tiny.windzz@xxxxxxxxx> wrote:
>
> HI Ondřej,
>
> On Sun, May 19, 2019 at 10:22 PM Ondřej Jirman <megous@xxxxxxxxxx> wrote:
> >
> > Hello Yangtao,
> >
> > On Sat, May 18, 2019 at 12:34:57AM +0800, Frank Lee wrote:
> > > HI,
> > >
> > > On Fri, May 17, 2019 at 2:29 AM Ondřej Jirman <megous@xxxxxxxxxx> wrote:
> > > >
> > > > Hi Yangtao,
> > > >
> > > > thank you for work on this driver.
> > > >
> > > > On Fri, May 17, 2019 at 02:06:53AM +0800, Frank Lee wrote:
> > > > > HI Ondřej,
> > > > >
> > > > > On Mon, May 13, 2019 at 6:16 AM Ondřej Jirman <megous@xxxxxxxxxx> wrote:
> > > > > > > +
> > > > > > > +/* Temp Unit: millidegree Celsius */
> > > > > > > +static int tsens_reg2temp(struct tsens_device *tmdev,
> > > > > > > + int reg)
> > > > > >
> > > > > > Please name all functions so that they are more clearly identifiable
> > > > > > in stack traces as belonging to this driver. For example:
> > > > > >
> > > > > > sun8i_ths_reg2temp
> > > > > >
> > > > > > The same applies for all tsens_* functions below. tsens_* is too
> > > > > > generic.
> > > > >
> > > > > Done but no sun8i_ths_reg2temp.
> > > > >
> > > > > ths_reg2tem() should be a generic func.
> > > > > I think it should be suitable for all platforms， so no platform prefix.
> > > >
> > > > You've missed my point. The driver name is sun8i_thermal and if you get
> > > > and oops from the kernel you'll get a stack trace where there are just function
> > > > names. If you use too generic function names, it will not be clear which
> > > > driver is oopsing.
> > > >
> > > > - sun8i_ths_reg2temp will tell you much more clearly where to search than
> > > > - ths_reg2temp
> > > >
> > > > Of course you can always grep, but most thermal drivers are thermal sensor (ths)
> > > > drivers, and if multiple of them used this too-generic naming scheme you'd
> > > > have hard time debugging.
> > > >
> > > > Look at other thermal drivers. They usually encode driver name in the function
> > > > names to help with identification (even if these are static driver-local
> > > > functions).
> > > >
> > >
> > > Can we change to sunxi_ths_ prefix?
> >
> > It should probably match the driver name, but yes, that's better.
> >
> > > > > > > +static int tsens_probe(struct platform_device *pdev)
> > > > > > > +{
> > > > > > > + struct tsens_device *tmdev;
> > > > > > > + struct device *dev = &pdev->dev;
> > > > > > > + int ret;
> > > > > > > +
> > > > > > > + tmdev = devm_kzalloc(dev, sizeof(*tmdev), GFP_KERNEL);
> > > > > > > + if (!tmdev)
> > > > > > > + return -ENOMEM;
> > > > > > > +
> > > > > > > + tmdev->dev = dev;
> > > > > > > + tmdev->chip = of_device_get_match_data(&pdev->dev);
> > > > > > > + if (!tmdev->chip)
> > > > > > > + return -EINVAL;
> > > > > > > +
> > > > > > > + ret = tsens_init(tmdev);
> > > > > > > + if (ret)
> > > > > > > + return ret;
> > > > > > > +
> > > > > > > + ret = tsens_register(tmdev);
> > > > > > > + if (ret)
> > > > > > > + return ret;
> > > > > >
> > > > > > Why split this out of probe into separate functions?
> > > > > >
> > > > > > > + ret = tmdev->chip->enable(tmdev);
> > > > > > > + if (ret)
> > > > > > > + return ret;
> > > > > > > +
> > > > > > > + platform_set_drvdata(pdev, tmdev);
> > > > > > > +
> > > > > > > + return ret;
> > > > > > > +}
> > > > > > > +
> > > > > > > +static int tsens_remove(struct platform_device *pdev)
> > > > > > > +{
> > > > > > > + struct tsens_device *tmdev = platform_get_drvdata(pdev);
> > > > > > > +
> > > > > > > + tmdev->chip->disable(tmdev);
> > > > > > > +
> > > > > > > + return 0;
> > > > > > > +}
> > > > > > > +
> > > > > > > +static int sun50i_thermal_enable(struct tsens_device *tmdev)
> > > > > > > +{
> > > > > > > + int ret, val;
> > > > > > > +
> > > > > > > + ret = reset_control_deassert(tmdev->reset);
> > > > > > > + if (ret)
> > > > > > > + return ret;
> > > > > > > +
> > > > > > > + ret = clk_prepare_enable(tmdev->bus_clk);
> > > > > > > + if (ret)
> > > > > > > + goto assert_reset;
> > > > > > > +
> > > > > > > + ret = tsens_calibrate(tmdev);
> > > > > > > + if (ret)
> > > > > > > + return ret;
> > > > > >
> > > > > > If this fails (it may likely fail with EPROBE_DEFER) you are leaving reset
> > > > > > deasserted, and clock enabled.
> > > > > >
> > > > > > Overall, I think, reset/clock management and nvmem reading will be common
> > > > > > to all the HW variants, so it doesn't make much sense splitting it out
> > > > > > of probe into separate functions, and makes it more error prone.
> > > > >
> > > > > Our long-term goal is to support all platforms.
> > > > > Bacicallt there is a differencr between each generation.
> > > > > So I feel it necessary to isolate these differences.
> > > > >
> > > > > Maybe:
> > > > > At some point, we can draw a part of the public part and platform
> > > > > difference into different
> > > > > files. something like qcom thermal driver.
> > > >
> > > > I understand, but I wrote ths drivers for H3/H5/A83T and it so far it looks like
> > > > all of them would share these 3 calls.
> > > >
> > > > You'll be enabling clock/reset and callibrating everywhere. So putting this to
> > > > per-SoC function seems premature.
> > >
> > > In fact, enalbe and disable are the suspend and resume functions.(PM
> > > callback will be added in the future)
> > > When exiting from s2ram, the register will become the initial value.
> > > We need to do all the work, enabling reset/clk ,calibrating and
> > > initializing other reg.
> > >
> > > So I think it is no need to put enabling reset/clk and calibrating to
> > > probe func, and I'd like
> > > to keep enable and disable func.
> >
> > I know, I don't think it needs to be per-soc. These actions are all shared by
> > all SoCs. Maybe with an exception that some SoCs may need one more clock, but
> > that can be made optionally-required by some flag in struct sunxi_thermal_chip.
> >
> > Only highly SoC specific thing is configuring the THS registers for sampling
> > frequency/averaging/enabling interrupts. The reset/clock enable is generic, and
> > already abstracted by the clock/reset framework.
> >
> > So what I suggest is having:
> >
> > sunxi_ths_enable()
> > reset deassert
> > bus clock prepare enable
> > optionally module clock prepare enable (in the future)
> > call per-soc calibration
> > call per-soc setup callback
> >
> > sunxi_ths_disable()
> > reset assert
> > bus clock unprepare disable
> > optionally module clock unprepare disable
> >
> > And if you could move devm_nvmem_cell_get to probe that should make per-SoC
> > calibration callback also less repetitive and could avoid undoing the enable
> > in case it returns EPROBE_DEFER (which is possible).
> >
> > All this should make it easier to support PM in the future and add less
> > cumbersome to add support for A83T and H3/H5.
> >
> > BTW, what are your plans for more SoC support? I'd like to add support for
> > A83T and H3/H5, maybe even during the 5.3 cycle if this driver happens to land
> > early enough. If you don't have any plans I'll take it on.
> >
>
> I plan to support h3 and a33 later.
> Can you support other platforms?
I'll work on A64 once this driver lands.
> Cheers,
> Yangtao
>
> > thank you and regards,
> > o.
> >
> > > >
> > > > thank you and regards,
> > > > o.
> > > >
> > > > > Regards,
> > > > > Yangtao
> > >
> > > _______________________________________________
> > > linux-arm-kernel mailing list
> > > linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
> > > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
