HI Ondřej,
On Mon, May 13, 2019 at 6:16 AM Ondřej Jirman <megous@xxxxxxxxxx> wrote:
>
> Hello Yangtao,
>
> On Sun, May 12, 2019 at 04:26:13AM -0400, Yangtao Li wrote:
> > diff --git a/drivers/thermal/sun50i_thermal.c b/drivers/thermal/sun50i_thermal.c
> > new file mode 100644
> > index 000000000000..3bdb3677b3d4
> > --- /dev/null
> > +++ b/drivers/thermal/sun50i_thermal.c
> > @@ -0,0 +1,357 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Thermal sensor driver for Allwinner SOC
> > + * Copyright (C) 2019 Yangtao Li
> > + *
> > + * Based on the work of Icenowy Zheng <icenowy@xxxxxxx>
> > + * Based on the work of Ondrej Jirman <megous@xxxxxxxxxx>
> > + * Based on the work of Josef Gajdusek <atx@xxxxxxxx>
> > + */
> > +
> > +#include <linux/clk.h>
> > +#include <linux/device.h>
> > +#include <linux/module.h>
> > +#include <linux/nvmem-consumer.h>
> > +#include <linux/of_device.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/regmap.h>
> > +#include <linux/reset.h>
> > +#include <linux/slab.h>
> > +#include <linux/thermal.h>
> > +
> > +#define MAX_SENSOR_NUM 4
> > +
> > +#define FT_TEMP_MASK GENMASK(11, 0)
> > +#define TEMP_CALIB_MASK GENMASK(11, 0)
> > +#define TEMP_TO_REG 672
> > +#define CALIBRATE_DEFAULT 0x800
> > +
> > +#define SUN50I_THS_CTRL0 0x00
> > +#define SUN50I_H6_THS_ENABLE 0x04
> > +#define SUN50I_H6_THS_PC 0x08
> > +#define SUN50I_H6_THS_MFC 0x30
> > +#define SUN50I_H6_TEMP_CALIB 0xa0
> > +#define SUN50I_H6_TEMP_DATA 0xc0
> > +
> > +#define SUN50I_THS_CTRL0_T_ACQ(x) ((GENMASK(15, 0) & (x)) << 16)
> > +#define SUN50I_THS_FILTER_EN BIT(2)
> > +#define SUN50I_THS_FILTER_TYPE(x) (GENMASK(1, 0) & (x))
> > +#define SUN50I_H6_THS_PC_TEMP_PERIOD(x) ((GENMASK(19, 0) & (x)) << 12)
> > +
> > +/* millidegree celsius */
> > +#define SUN50I_H6_FT_DEVIATION 7000
> > +
> > +struct tsens_device;
> > +
> > +struct tsensor {
> > + struct tsens_device *tmdev;
> > + struct thermal_zone_device *tzd;
> > + int id;
> > +};
> > +
> > +struct sun50i_thermal_chip {
> > + int sensor_num;
> > + int offset;
> > + int scale;
> > + int ft_deviation;
> > + int temp_calib_base;
> > + int temp_data_base;
> > + int (*enable)(struct tsens_device *tmdev);
> > + int (*disable)(struct tsens_device *tmdev);
> > +};
> > +
> > +
> > +struct tsens_device {
> > + const struct sun50i_thermal_chip *chip;
> > + struct device *dev;
> > + struct regmap *regmap;
> > + struct reset_control *reset;
> > + struct clk *bus_clk;
> > + struct tsensor sensor[MAX_SENSOR_NUM];
> > +};
> > +
> > +/* Temp Unit: millidegree Celsius */
> > +static int tsens_reg2temp(struct tsens_device *tmdev,
> > + int reg)
>
> Please name all functions so that they are more clearly identifiable
> in stack traces as belonging to this driver. For example:
>
> sun8i_ths_reg2temp
>
> The same applies for all tsens_* functions below. tsens_* is too
> generic.
Done but no sun8i_ths_reg2temp.
ths_reg2tem() should be a generic func.
I think it should be suitable for all platforms， so no platform prefix.
>
> > +{
> > + return (reg + tmdev->chip->offset) * tmdev->chip->scale;
> > +}
> > +
> > +static int tsens_get_temp(void *data, int *temp)
> > +{
> > + struct tsensor *s = data;
> > + struct tsens_device *tmdev = s->tmdev;
> > + int val;
> > +
> > + regmap_read(tmdev->regmap, tmdev->chip->temp_data_base +
> > + 0x4 * s->id, &val);
> > +
> > + if (unlikely(val == 0))
> > + return -EBUSY;
> > +
> > + *temp = tsens_reg2temp(tmdev, val);
> > + if (tmdev->chip->ft_deviation)
> > + *temp += tmdev->chip->ft_deviation;
> > +
> > + return 0;
> > +}
> > +
> > +static const struct thermal_zone_of_device_ops tsens_ops = {
> > + .get_temp = tsens_get_temp,
> > +};
> > +
> > +static const struct regmap_config config = {
> > + .reg_bits = 32,
> > + .val_bits = 32,
> > + .reg_stride = 4,
> > + .fast_io = true,
> > +};
> > +
> > +static int tsens_init(struct tsens_device *tmdev)
> > +{
> > + struct device *dev = tmdev->dev;
> > + struct platform_device *pdev = to_platform_device(dev);
> > + struct resource *mem;
> > + void __iomem *base;
> > +
> > + mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > + base = devm_ioremap_resource(dev, mem);
> > + if (IS_ERR(base))
> > + return PTR_ERR(base);
> > +
> > + tmdev->regmap = devm_regmap_init_mmio_clk(dev, "bus",
> > + base,
> > + &config);
> > + if (IS_ERR(tmdev->regmap))
> > + return PTR_ERR(tmdev->regmap);
> > +
> > + tmdev->reset = devm_reset_control_get(dev, "bus");
> > + if (IS_ERR(tmdev->reset))
> > + return PTR_ERR(tmdev->reset);
> > +
> > + tmdev->bus_clk = devm_clk_get(&pdev->dev, "bus");
> > + if (IS_ERR(tmdev->bus_clk))
> > + return PTR_ERR(tmdev->bus_clk);
> > +
> > + return 0;
> > +}
> > +
> > +/*
> > + * Even if the external calibration data stored in sid is not accessible,
> > + * the THS hardware can still work, although the data won't be so accurate.
> > + * The default value of calibration register is 0x800 for every sensor,
> > + * and the calibration value is usually 0x7xx or 0x8xx, so they won't be
> > + * away from the default value for a lot.
> > + *
> > + * So here we do not return error if the calibartion data is
> > + * not available, except the probe needs deferring.
> > + */
> > +static int tsens_calibrate(struct tsens_device *tmdev)
> > +{
> > + struct nvmem_cell *calcell;
> > + struct device *dev = tmdev->dev;
> > + u16 *caldata;
> > + size_t callen;
> > + int ft_temp;
> > + int i = 0;
> > +
> > + calcell = devm_nvmem_cell_get(dev, "calib");
> > + if (IS_ERR(calcell)) {
> > + if (PTR_ERR(calcell) == -EPROBE_DEFER)
> > + return -EPROBE_DEFER;
> > +
> > + goto out;
> > + }
> > +
> > + caldata = nvmem_cell_read(calcell, &callen);
> > + if (IS_ERR(caldata))
> > + goto out;
> > +
> > + if (!caldata[0] || callen < 2 + 2 * tmdev->chip->sensor_num)
> > + goto out_free;
> > +
> > + /*
> > + * The calbration data on H6 is stored as temperature-value
> > + * pair when being filled at factory test stage.
> > + * The unit of stored FT temperature is 0.1 degreee celusis.
> > + */
>
> Please describe the calibration data layout more clearly.
Done.
>
> > + ft_temp = caldata[0] & FT_TEMP_MASK;
> > +
> > + for (; i < tmdev->chip->sensor_num; i++) {
> > + int reg = (int)caldata[i + 1];
> > + int sensor_temp = tsens_reg2temp(tmdev, reg);
> > + int delta, cdata, calib_offest;
> > +
> > + /*
> > + * To calculate the calibration value:
> > + *
> > + * X(in Celsius) = Ts - ft_temp
> > + * delta = X * 10000 / TEMP_TO_REG
> > + * cdata = CALIBRATE_DEFAULT - delta
> > + *
> > + * cdata: calibration value
> > + */
> > + delta = (sensor_temp - ft_temp * 100) * 10 / TEMP_TO_REG;
> > + cdata = CALIBRATE_DEFAULT - delta;
> > + if (cdata & ~TEMP_CALIB_MASK) {
> > + dev_warn(dev, "sensor%d calibration value error", i);
>
> Please use a more descriptive error message. What error is this?
See commnt in v2.
>
> > + continue;
> > + }
> > +
> > + calib_offest = tmdev->chip->temp_calib_base + (i / 2) * 0x4;
> > + if (i % 2) {
> > + int val;
> > +
> > + regmap_read(tmdev->regmap, calib_offest, &val);
> > + val = (val & TEMP_CALIB_MASK) | (cdata << 16);
> > + regmap_write(tmdev->regmap, calib_offest, val);
> > + } else
> > + regmap_write(tmdev->regmap, calib_offest, cdata);
> > + }
> > +
> > +out_free:
> > + kfree(caldata);
> > +out:
> > + return 0;
> > +}
> > +
> > +static int tsens_register(struct tsens_device *tmdev)
> > +{
> > + struct thermal_zone_device *tzd;
> > + int i = 0;
> > +
> > + for (; i < tmdev->chip->sensor_num; i++) {
> > + tmdev->sensor[i].tmdev = tmdev;
> > + tmdev->sensor[i].id = i;
> > + tmdev->sensor[i].tzd = devm_thermal_zone_of_sensor_register(
> > + tmdev->dev, i, &tmdev->sensor[i],
> > + &tsens_ops);
> > + if (IS_ERR(tmdev->sensor[i].tzd))
> > + return PTR_ERR(tzd);
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int tsens_probe(struct platform_device *pdev)
> > +{
> > + struct tsens_device *tmdev;
> > + struct device *dev = &pdev->dev;
> > + int ret;
> > +
> > + tmdev = devm_kzalloc(dev, sizeof(*tmdev), GFP_KERNEL);
> > + if (!tmdev)
> > + return -ENOMEM;
> > +
> > + tmdev->dev = dev;
> > + tmdev->chip = of_device_get_match_data(&pdev->dev);
> > + if (!tmdev->chip)
> > + return -EINVAL;
> > +
> > + ret = tsens_init(tmdev);
> > + if (ret)
> > + return ret;
> > +
> > + ret = tsens_register(tmdev);
> > + if (ret)
> > + return ret;
>
> Why split this out of probe into separate functions?
>
> > + ret = tmdev->chip->enable(tmdev);
> > + if (ret)
> > + return ret;
> > +
> > + platform_set_drvdata(pdev, tmdev);
> > +
> > + return ret;
> > +}
> > +
> > +static int tsens_remove(struct platform_device *pdev)
> > +{
> > + struct tsens_device *tmdev = platform_get_drvdata(pdev);
> > +
> > + tmdev->chip->disable(tmdev);
> > +
> > + return 0;
> > +}
> > +
> > +static int sun50i_thermal_enable(struct tsens_device *tmdev)
> > +{
> > + int ret, val;
> > +
> > + ret = reset_control_deassert(tmdev->reset);
> > + if (ret)
> > + return ret;
> > +
> > + ret = clk_prepare_enable(tmdev->bus_clk);
> > + if (ret)
> > + goto assert_reset;
> > +
> > + ret = tsens_calibrate(tmdev);
> > + if (ret)
> > + return ret;
>
> If this fails (it may likely fail with EPROBE_DEFER) you are leaving reset
> deasserted, and clock enabled.
>
> Overall, I think, reset/clock management and nvmem reading will be common
> to all the HW variants, so it doesn't make much sense splitting it out
> of probe into separate functions, and makes it more error prone.
Our long-term goal is to support all platforms.
Bacicallt there is a differencr between each generation.
So I feel it necessary to isolate these differences.
Maybe:
At some point, we can draw a part of the public part and platform
difference into different
files. something like qcom thermal driver.
Regards,
Yangtao
>
> thank you and regards,
> o.
>
> > + /*
> > + * clkin = 24MHz
> > + * T acquire = clkin / (SUN50I_THS_CTRL0_T_ACQ + 1)
> > + * = 20us
> > + */
> > + regmap_write(tmdev->regmap, SUN50I_THS_CTRL0,
> > + SUN50I_THS_CTRL0_T_ACQ(479));
> > + /* average over 4 samples */
> > + regmap_write(tmdev->regmap, SUN50I_H6_THS_MFC,
> > + SUN50I_THS_FILTER_EN |
> > + SUN50I_THS_FILTER_TYPE(1));
> > + /* period = (SUN50I_H6_THS_PC_TEMP_PERIOD + 1) * 4096 / clkin; ~10ms */
> > + regmap_write(tmdev->regmap, SUN50I_H6_THS_PC,
> > + SUN50I_H6_THS_PC_TEMP_PERIOD(58));
> > + /* enable sensor */
> > + val = GENMASK(tmdev->chip->sensor_num - 1, 0);
> > + regmap_write(tmdev->regmap, SUN50I_H6_THS_ENABLE, val);
> > +
> > + return 0;
> > +
> > +assert_reset:
> > + reset_control_assert(tmdev->reset);
> > +
> > + return ret;
> > +}
> > +
> > +static int sun50i_thermal_disable(struct tsens_device *tmdev)
> > +{
> > + clk_disable_unprepare(tmdev->bus_clk);
> > + reset_control_assert(tmdev->reset);
> > +
> > + return 0;
> > +}
> > +
> > +static const struct sun50i_thermal_chip sun50i_h6_ths = {
> > + .sensor_num = 2,
> > + .offset = -2794,
> > + .scale = -67,
> > + .ft_deviation = SUN50I_H6_FT_DEVIATION,
> > + .temp_calib_base = SUN50I_H6_TEMP_CALIB,
> > + .temp_data_base = SUN50I_H6_TEMP_DATA,
> > + .enable = sun50i_thermal_enable,
> > + .disable = sun50i_thermal_disable,
> > +};
> > +
> > +static const struct of_device_id of_tsens_match[] = {
> > + { .compatible = "allwinner,sun50i-h6-ths", .data = &sun50i_h6_ths },
> > + { /* sentinel */ },
> > +};
> > +MODULE_DEVICE_TABLE(of, of_tsens_match);
> > +
> > +static struct platform_driver tsens_driver = {
> > + .probe = tsens_probe,
> > + .remove = tsens_remove,
> > + .driver = {
> > + .name = "sun50i-thermal",
> > + .of_match_table = of_tsens_match,
> > + },
> > +};
> > +module_platform_driver(tsens_driver);
> > +
> > +MODULE_DESCRIPTION("Thermal sensor driver for Allwinner SOC");
> > +MODULE_LICENSE("GPL v2");
> > --
> > 2.17.0
> >
> >
> > _______________________________________________
> > linux-arm-kernel mailing list
> > linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
> > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
