On 02/05/2019 12:43, michael.kao wrote:
> Add thermal zone node to Mediatek MT8183 dts file.
>
> Signed-off-by: Michael Kao <michael.kao@xxxxxxxxxxxx>
> ---
Hi Michael,
the device tree binding for thermal specifies the thermal zone must
define a cooling-maps (it is a required field).
All the thermal zones below tzts1, tzts2, etc ... do not have it.
> arch/arm64/boot/dts/mediatek/mt8183.dtsi | 64 ++++++++++++++++++++++++++++++++
> 1 file changed, 64 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/mediatek/mt8183.dtsi b/arch/arm64/boot/dts/mediatek/mt8183.dtsi
> index 926df75..b92116f 100644
> --- a/arch/arm64/boot/dts/mediatek/mt8183.dtsi
> +++ b/arch/arm64/boot/dts/mediatek/mt8183.dtsi
> @@ -334,6 +334,67 @@
> status = "disabled";
> };
>
> + thermal: thermal@1100b000 {
> + #thermal-sensor-cells = <1>;
> + compatible = "mediatek,mt8183-thermal";
> + reg = <0 0x1100b000 0 0x1000>;
> + interrupts = <0 76 IRQ_TYPE_LEVEL_LOW>;
> + clocks = <&infracfg CLK_INFRA_THERM>,
> + <&infracfg CLK_INFRA_AUXADC>;
> + clock-names = "therm", "auxadc";
> + resets = <&infracfg MT8183_INFRACFG_AO_THERM_SW_RST>;
> + mediatek,auxadc = <&auxadc>;
> + mediatek,apmixedsys = <&apmixedsys>;
> + mediatek,hw-reset-temp = <117000>;
> + nvmem-cells = <&thermal_calibration>;
> + nvmem-cell-names = "calibration-data";
> + };
> +
> + thermal-zones {
> + cpu_thermal: cpu_thermal {
> + polling-delay-passive = <1000>;
> + polling-delay = <1000>;
> +
> + thermal-sensors = <&thermal 0>;
> + sustainable-power = <1500>;
> + };
> +
> + tzts1: tzts1 {
> + polling-delay-passive = <1000>;
> + polling-delay = <1000>;
> + thermal-sensors = <&thermal 1>;
> + };
> +
> + tzts2: tzts2 {
> + polling-delay-passive = <1000>;
> + polling-delay = <1000>;
> + thermal-sensors = <&thermal 2>;
> + };
> +
> + tzts3: tzts3 {
> + polling-delay-passive = <1000>;
> + polling-delay = <1000>;
> + thermal-sensors = <&thermal 3>;
> + };
> +
> + tzts4: tzts4 {
> + polling-delay-passive = <1000>;
> + polling-delay = <1000>;
> + thermal-sensors = <&thermal 4>;
> + };
> +
> + tzts5: tzts5 {
> + polling-delay-passive = <1000>;
> + polling-delay = <1000>;
> + thermal-sensors = <&thermal 5>;
> + };
> +
> + tztsABB: tztsABB {
> + polling-delay-passive = <1000>;
> + polling-delay = <1000>;
> + thermal-sensors = <&thermal 6>;
> + };
> + };
> audiosys: syscon@11220000 {
> compatible = "mediatek,mt8183-audiosys", "syscon";
> reg = <0 0x11220000 0 0x1000>;
> @@ -368,6 +429,9 @@
> compatible = "mediatek,mt8183-efuse",
> "mediatek,efuse";
> reg = <0 0x11f10000 0 0x1000>;
> + thermal_calibration: calib@180 {
> + reg = <0x180 0xc>;
> + };
> };
>
> mfgcfg: syscon@13000000 {
>
--
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs
Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
