Re: [PATCH v2 1/2] SPI: Add driver for Cadence SPI controller

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On Thu, Apr 03, 2014 at 04:40:30PM +0530, Harini Katakam wrote:
> Add driver for Cadence SPI controller. This is used in Xilinx Zynq.

I just reviewed a driver for "Zynq Quad SPI controller" from Punnaiah
Choudary Kalluri (CCed) which seems *very* similar to this one.  Are
there opportunities for code sharing here (I'm not entirely sure the
hardware blocks are different, though I didn't check in detail).

I've left the entire context in for the benefit of those I just CCed in.

> Signed-off-by: Harini Katakam <harinik@xxxxxxxxxx>
> ---
> 
> v2 changes:
> - Use xilinx compatible string too.
> - Changes read register and write register functions to static inline.
> - Removed unecessary dev_info and dev_dbg prints.
> - Return IRQ_HANDLED only when interrupt is handled.
> - Use a default num-cs value.
> - Do init_hardware before requesting irq.
> - Remove unecessary master_put()
> - Set master->max_speed_hz
> - Check for busy in cdns_setup().
>   Retained this function with this check as opposed to removing.
>   The reason for this is clock configuration needs to be done for
>   the first time before enable is done in prepare_hardware;
>   prepare_hardware however, doesn't receive spi_device structure.
> - Implememnt transfer_one instead of transfer_one_message.
>   Remove wait_for_completion as this is done by core.
> - Implement set_cs.
> - Clock enable/disable in prepare/unprepare respectively.
> - In suspend, remove reset of hardware; simply call unprepare_hardware.
> - In suspend/resume call master_suspend/resume respectively.
> - Check for irq<=0 in probe.
> - Remove MODULE_ALIAS.
> 
> ---
>  drivers/spi/Kconfig       |    7 +
>  drivers/spi/Makefile      |    1 +
>  drivers/spi/spi-cadence.c |  677 +++++++++++++++++++++++++++++++++++++++++++++
>  3 files changed, 685 insertions(+)
>  create mode 100644 drivers/spi/spi-cadence.c
> 
> diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
> index 581ee2a..aeae44a 100644
> --- a/drivers/spi/Kconfig
> +++ b/drivers/spi/Kconfig
> @@ -148,6 +148,13 @@ config SPI_BUTTERFLY
>  	  inexpensive battery powered microcontroller evaluation board.
>  	  This same cable can be used to flash new firmware.
>  
> +config SPI_CADENCE
> +	tristate "Cadence SPI controller"
> +	depends on SPI_MASTER
> +	help
> +	  This selects the Cadence SPI controller master driver
> +	  used by Xilinx Zynq.
> +
>  config SPI_CLPS711X
>  	tristate "CLPS711X host SPI controller"
>  	depends on ARCH_CLPS711X
> diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
> index 95af48d..1be2ed7 100644
> --- a/drivers/spi/Makefile
> +++ b/drivers/spi/Makefile
> @@ -22,6 +22,7 @@ obj-$(CONFIG_SPI_BFIN_V3)               += spi-bfin-v3.o
>  obj-$(CONFIG_SPI_BFIN_SPORT)		+= spi-bfin-sport.o
>  obj-$(CONFIG_SPI_BITBANG)		+= spi-bitbang.o
>  obj-$(CONFIG_SPI_BUTTERFLY)		+= spi-butterfly.o
> +obj-$(CONFIG_SPI_CADENCE)		+= spi-cadence.o
>  obj-$(CONFIG_SPI_CLPS711X)		+= spi-clps711x.o
>  obj-$(CONFIG_SPI_COLDFIRE_QSPI)		+= spi-coldfire-qspi.o
>  obj-$(CONFIG_SPI_DAVINCI)		+= spi-davinci.o
> diff --git a/drivers/spi/spi-cadence.c b/drivers/spi/spi-cadence.c
> new file mode 100644
> index 0000000..071642d
> --- /dev/null
> +++ b/drivers/spi/spi-cadence.c
> @@ -0,0 +1,677 @@
> +/*
> + * Cadence SPI controller driver (master mode only)
> + *
> + * Copyright (C) 2008 - 2014 Xilinx, Inc.
> + *
> + * based on Blackfin On-Chip SPI Driver (spi_bfin5xx.c)
> + *
> + * This program is free software; you can redistribute it and/or modify it under
> + * the terms of the GNU General Public License version 2 as published by the
> + * Free Software Foundation; either version 2 of the License, or (at your
> + * option) any later version.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/interrupt.h>
> +#include <linux/io.h>
> +#include <linux/module.h>
> +#include <linux/of_irq.h>
> +#include <linux/of_address.h>
> +#include <linux/platform_device.h>
> +#include <linux/spi/spi.h>
> +
> +/* Name of this driver */
> +#define CDNS_SPI_NAME		"cdns-spi"
> +
> +/* Register offset definitions */
> +#define CDNS_SPI_CR_OFFSET	0x00 /* Configuration  Register, RW */
> +#define CDNS_SPI_ISR_OFFSET	0x04 /* Interrupt Status Register, RO */
> +#define CDNS_SPI_IER_OFFSET	0x08 /* Interrupt Enable Register, WO */
> +#define CDNS_SPI_IDR_OFFSET	0x0c /* Interrupt Disable Register, WO */
> +#define CDNS_SPI_IMR_OFFSET	0x10 /* Interrupt Enabled Mask Register, RO */
> +#define CDNS_SPI_ER_OFFSET	0x14 /* Enable/Disable Register, RW */
> +#define CDNS_SPI_DR_OFFSET	0x18 /* Delay Register, RW */
> +#define CDNS_SPI_TXD_OFFSET	0x1C /* Data Transmit Register, WO */
> +#define CDNS_SPI_RXD_OFFSET	0x20 /* Data Receive Register, RO */
> +#define CDNS_SPI_SICR_OFFSET	0x24 /* Slave Idle Count Register, RW */
> +#define CDNS_SPI_THLD_OFFSET	0x28 /* Transmit FIFO Watermark Register,RW */
> +
> +/*
> + * SPI Configuration Register bit Masks
> + *
> + * This register contains various control bits that affect the operation
> + * of the SPI controller
> + */
> +#define CDNS_SPI_CR_MANSTRT_MASK	0x00010000 /* Manual TX Start */
> +#define CDNS_SPI_CR_CPHA_MASK		0x00000004 /* Clock Phase Control */
> +#define CDNS_SPI_CR_CPOL_MASK		0x00000002 /* Clock Polarity Control */
> +#define CDNS_SPI_CR_SSCTRL_MASK		0x00003C00 /* Slave Select Mask */
> +#define CDNS_SPI_CR_BAUD_DIV_MASK	0x00000038 /* Baud Rate Divisor Mask */
> +#define CDNS_SPI_CR_MSTREN_MASK		0x00000001 /* Master Enable Mask */
> +#define CDNS_SPI_CR_MANSTRTEN_MASK	0x00008000 /* Manual TX Enable Mask */
> +#define CDNS_SPI_CR_SSFORCE_MASK	0x00004000 /* Manual SS Enable Mask */
> +#define CDNS_SPI_CR_BAUD_DIV_4_MASK	0x00000008 /* Default Baud Div Mask */
> +#define CDNS_SPI_CR_DEFAULT_MASK	(CDNS_SPI_CR_MSTREN_MASK | \
> +					CDNS_SPI_CR_SSCTRL_MASK | \
> +					CDNS_SPI_CR_SSFORCE_MASK | \
> +					CDNS_SPI_CR_BAUD_DIV_4_MASK)
> +
> +/*
> + * SPI Configuration Register - Baud rate and slave select
> + *
> + * These are the values used in the calculation of baud rate divisor and
> + * setting the slave select.
> + */
> +
> +#define CDNS_SPI_BAUD_DIV_MAX		7 /* Baud rate divisor maximum */
> +#define CDNS_SPI_BAUD_DIV_MIN		1 /* Baud rate divisor minimum */
> +#define CDNS_SPI_BAUD_DIV_SHIFT		3 /* Baud rate divisor shift in CR */
> +#define CDNS_SPI_SS_SHIFT		10 /* Slave Select field shift in CR */
> +#define CDNS_SPI_SS0			0x1 /* Slave Select zero */
> +
> +/*
> + * SPI Interrupt Registers bit Masks
> + *
> + * All the four interrupt registers (Status/Mask/Enable/Disable) have the same
> + * bit definitions.
> + */
> +#define CDNS_SPI_IXR_TXOW_MASK	0x00000004 /* SPI TX FIFO Overwater */
> +#define CDNS_SPI_IXR_MODF_MASK	0x00000002 /* SPI Mode Fault */
> +#define CDNS_SPI_IXR_RXNEMTY_MASK 0x00000010 /* SPI RX FIFO Not Empty */
> +#define CDNS_SPI_IXR_DEFAULT_MASK	(CDNS_SPI_IXR_TXOW_MASK | \
> +					CDNS_SPI_IXR_MODF_MASK)
> +#define CDNS_SPI_IXR_TXFULL_MASK	0x00000008 /* SPI TX Full */
> +#define CDNS_SPI_IXR_ALL_MASK	0x0000007F /* SPI all interrupts */
> +
> +/*
> + * SPI Enable Register bit Masks
> + *
> + * This register is used to enable or disable the SPI controller
> + */
> +#define CDNS_SPI_ER_ENABLE_MASK	0x00000001 /* SPI Enable Bit Mask */
> +#define CDNS_SPI_ER_DISABLE_MASK	0x0 /* SPI Disable Bit Mask */
> +
> +/* SPI timeout value */
> +#define CDNS_SPI_TIMEOUT	(5 * HZ)
> +
> +/* SPI FIFO depth in bytes */
> +#define CDNS_SPI_FIFO_DEPTH	128
> +
> +/* Default number of chip select lines */
> +#define CDNS_SPI_DEFAULT_NUM_CS		4
> +
> +/* Driver state - suspend/ready */
> +enum driver_state_val {
> +	CDNS_SPI_DRIVER_STATE_READY = 0,
> +	CDNS_SPI_DRIVER_STATE_SUSPEND
> +};
> +
> +/**
> + * struct cdns_spi - This definition defines spi driver instance
> + * @regs:		Virtual address of the SPI controller registers
> + * @ref_clk:		Pointer to the peripheral clock
> + * @pclk:		Pointer to the APB clock
> + * @speed_hz:		Current SPI bus clock speed in Hz
> + * @txbuf:		Pointer	to the TX buffer
> + * @rxbuf:		Pointer to the RX buffer
> + * @remaining_bytes:	Number of bytes left to transfer
> + * @requested_bytes:	Number of bytes requested
> + * @dev_busy:		Device busy flag
> + * @done:		Transfer complete status
> + * @driver_state:	Describes driver state - ready/suspended
> + */
> +struct cdns_spi {
> +	void __iomem *regs;
> +	struct clk *ref_clk;
> +	struct clk *pclk;
> +	u32 speed_hz;
> +	const u8 *txbuf;
> +	u8 *rxbuf;
> +	int remaining_bytes;
> +	int requested_bytes;
> +	u8 dev_busy;
> +	enum driver_state_val driver_state;
> +};
> +
> +/* Macros for the SPI controller read/write */
> +static inline u32 cdns_spi_read(struct cdns_spi *xspi, u32 offset)
> +{
> +	return readl_relaxed(xspi->regs + offset);
> +}
> +
> +static inline void cdns_spi_write(struct cdns_spi *xspi, u32 offset, u32 val)
> +{
> +	writel_relaxed(val, xspi->regs + offset);
> +}
> +
> +/**
> + * cdns_spi_init_hw - Initialize the hardware and configure the SPI controller
> + * @xspi:	Pointer to the cdns_spi structure
> + *
> + * On reset the SPI controller is configured to be in master mode, baud rate
> + * divisor is set to 4, threshold value for TX FIFO not full interrupt is set
> + * to 1 and size of the word to be transferred as 8 bit.
> + * This function initializes the SPI controller to disable and clear all the
> + * interrupts, enable manual slave select and manual start, deselect all the
> + * chip select lines, and enable the SPI controller.
> + */
> +static void cdns_spi_init_hw(struct cdns_spi *xspi)
> +{
> +	cdns_spi_write(xspi, CDNS_SPI_ER_OFFSET,
> +		       CDNS_SPI_ER_DISABLE_MASK);
> +	cdns_spi_write(xspi, CDNS_SPI_IDR_OFFSET,
> +		       CDNS_SPI_IXR_ALL_MASK);
> +
> +	/* Clear the RX FIFO */
> +	while (cdns_spi_read(xspi, CDNS_SPI_ISR_OFFSET) &
> +	       CDNS_SPI_IXR_RXNEMTY_MASK)
> +		cdns_spi_read(xspi, CDNS_SPI_RXD_OFFSET);
> +
> +	cdns_spi_write(xspi, CDNS_SPI_ISR_OFFSET,
> +		       CDNS_SPI_IXR_ALL_MASK);
> +	cdns_spi_write(xspi, CDNS_SPI_CR_OFFSET,
> +		       CDNS_SPI_CR_DEFAULT_MASK);
> +	cdns_spi_write(xspi, CDNS_SPI_ER_OFFSET,
> +		       CDNS_SPI_ER_ENABLE_MASK);
> +}
> +
> +/**
> + * cdns_spi_chipselect - Select or deselect the chip select line
> + * @spi:	Pointer to the spi_device structure
> + * @is_on:	Select(0) or deselect (1) the chip select line
> + */
> +static void cdns_spi_chipselect(struct spi_device *spi, bool is_high)
> +{
> +	struct cdns_spi *xspi = spi_master_get_devdata(spi->master);
> +	u32 ctrl_reg;
> +
> +	ctrl_reg = cdns_spi_read(xspi, CDNS_SPI_CR_OFFSET);
> +
> +	if (is_high) {
> +		/* Deselect the slave */
> +		ctrl_reg |= CDNS_SPI_CR_SSCTRL_MASK;
> +	} else {
> +		/* Select the slave */
> +		ctrl_reg &= ~CDNS_SPI_CR_SSCTRL_MASK;
> +		ctrl_reg |= ((~(CDNS_SPI_SS0 << spi->chip_select)) <<
> +			     CDNS_SPI_SS_SHIFT) & CDNS_SPI_CR_SSCTRL_MASK;
> +	}
> +
> +	cdns_spi_write(xspi, CDNS_SPI_CR_OFFSET, ctrl_reg);
> +}
> +
> +/**
> + * cdns_spi_config_clock - Sets clock polarity, phase and frequency
> + * @spi:	Pointer to the spi_device structure
> + * @transfer:	Pointer to the spi_transfer structure which provides
> + *		information about next transfer setup parameters
> + *
> + * Sets the requested clock polarity, phase and frequency.
> + * Note: If the requested frequency is not an exact match with what can be
> + * obtained using the prescalar value the driver sets the clock frequency which
> + * is lower than the requested frequency (maximum lower) for the transfer. If
> + * the requested frequency is higher or lower than that is supported by the SPI
> + * controller the driver will set the highest or lowest frequency supported by
> + * controller.
> + */
> +static void cdns_spi_config_clock(struct spi_device *spi,
> +				  struct spi_transfer *transfer)
> +{
> +	struct cdns_spi *xspi = spi_master_get_devdata(spi->master);
> +	u32 ctrl_reg, req_hz, baud_rate_val;
> +	unsigned long frequency;
> +
> +	if (transfer)
> +		req_hz = transfer->speed_hz;
> +	else
> +		req_hz = spi->max_speed_hz;
> +
> +	frequency = clk_get_rate(xspi->ref_clk);
> +
> +	ctrl_reg = cdns_spi_read(xspi, CDNS_SPI_CR_OFFSET);
> +
> +	/* Set the SPI clock phase and clock polarity */
> +	ctrl_reg &= ~(CDNS_SPI_CR_CPHA_MASK | CDNS_SPI_CR_CPOL_MASK);
> +	if (spi->mode & SPI_CPHA)
> +		ctrl_reg |= CDNS_SPI_CR_CPHA_MASK;
> +	if (spi->mode & SPI_CPOL)
> +		ctrl_reg |= CDNS_SPI_CR_CPOL_MASK;
> +
> +	/* Set the clock frequency */
> +	if (xspi->speed_hz != req_hz) {
> +		/* first valid value is 1 */
> +		baud_rate_val = CDNS_SPI_BAUD_DIV_MIN;
> +		while ((baud_rate_val < CDNS_SPI_BAUD_DIV_MAX) &&
> +		       (frequency / (2 << baud_rate_val)) > req_hz)
> +			baud_rate_val++;
> +
> +		ctrl_reg &= ~CDNS_SPI_CR_BAUD_DIV_MASK;
> +		ctrl_reg |= baud_rate_val << CDNS_SPI_BAUD_DIV_SHIFT;
> +
> +		xspi->speed_hz = frequency / (2 << baud_rate_val);
> +	}
> +	cdns_spi_write(xspi, CDNS_SPI_CR_OFFSET, ctrl_reg);
> +}
> +
> +/**
> + * cdns_spi_setup_transfer - Configure SPI controller for specified transfer
> + * @spi:	Pointer to the spi_device structure
> + * @transfer:	Pointer to the spi_transfer structure which provides
> + *		information about next transfer setup parameters
> + *
> + * Sets the operational mode of SPI controller for the next SPI transfer and
> + * sets the requested clock frequency.
> + *
> + * Return:	Always 0
> + */
> +static int cdns_spi_setup_transfer(struct spi_device *spi,
> +				   struct spi_transfer *transfer)
> +{
> +	struct cdns_spi *xspi = spi_master_get_devdata(spi->master);
> +
> +	cdns_spi_config_clock(spi, transfer);
> +
> +	dev_dbg(&spi->dev, "%s, mode %d, %u bits/w, %u clock speed\n",
> +		__func__, spi->mode, spi->bits_per_word,
> +		xspi->speed_hz);
> +
> +	return 0;
> +}
> +
> +/**
> + * cdns_spi_setup - Configure the SPI controller
> + * @spi:	Pointer to the spi_device structure
> + *
> + * Sets the operational mode of SPI controller for the next SPI transfer, sets
> + * the baud rate and divisor value to setup the requested spi clock.
> + *
> + * Return:	0 on success and error value on error
> + */
> +static int cdns_spi_setup(struct spi_device *spi)
> +{
> +	if (spi->master->busy)
> +		return -EBUSY;
> +
> +	return cdns_spi_setup_transfer(spi, NULL);
> +}
> +
> +/**
> + * cdns_spi_fill_tx_fifo - Fills the TX FIFO with as many bytes as possible
> + * @xspi:	Pointer to the cdns_spi structure
> + */
> +static void cdns_spi_fill_tx_fifo(struct cdns_spi *xspi)
> +{
> +	unsigned long trans_cnt = 0;
> +
> +	while ((trans_cnt < CDNS_SPI_FIFO_DEPTH) &&
> +	       (xspi->remaining_bytes > 0)) {
> +		if (xspi->txbuf)
> +			cdns_spi_write(xspi, CDNS_SPI_TXD_OFFSET,
> +				       *xspi->txbuf++);
> +		else
> +			cdns_spi_write(xspi, CDNS_SPI_TXD_OFFSET, 0);
> +
> +		xspi->remaining_bytes--;
> +		trans_cnt++;
> +	}
> +}
> +
> +/**
> + * cdns_spi_irq - Interrupt service routine of the SPI controller
> + * @irq:	IRQ number
> + * @dev_id:	Pointer to the xspi structure
> + *
> + * This function handles TX empty and Mode Fault interrupts only.
> + * On TX empty interrupt this function reads the received data from RX FIFO and
> + * fills the TX FIFO if there is any data remaining to be transferred.
> + * On Mode Fault interrupt this function indicates that transfer is completed,
> + * the SPI subsystem will identify the error as the remaining bytes to be
> + * transferred is non-zero.
> + *
> + * Return:	IRQ_HANDLED when handled; IRQ_NONE otherwise.
> + */
> +static irqreturn_t cdns_spi_irq(int irq, void *dev_id)
> +{
> +	struct spi_master *master = dev_id;
> +	struct cdns_spi *xspi = spi_master_get_devdata(master);
> +	u32 intr_status, status;
> +
> +	status = IRQ_NONE;
> +	intr_status = cdns_spi_read(xspi, CDNS_SPI_ISR_OFFSET);
> +	cdns_spi_write(xspi, CDNS_SPI_ISR_OFFSET, intr_status);
> +
> +	if (intr_status & CDNS_SPI_IXR_MODF_MASK) {
> +		/* Indicate that transfer is completed, the SPI subsystem will
> +		 * identify the error as the remaining bytes to be
> +		 * transferred is non-zero
> +		 */
> +		cdns_spi_write(xspi, CDNS_SPI_IDR_OFFSET,
> +			       CDNS_SPI_IXR_DEFAULT_MASK);
> +		spi_finalize_current_transfer(master);
> +		status = IRQ_HANDLED;
> +	} else if (intr_status & CDNS_SPI_IXR_TXOW_MASK) {
> +		unsigned long trans_cnt;
> +
> +		trans_cnt = xspi->requested_bytes - xspi->remaining_bytes;
> +
> +		/* Read out the data from the RX FIFO */
> +		while (trans_cnt) {
> +			u8 data;
> +
> +			data = cdns_spi_read(xspi, CDNS_SPI_RXD_OFFSET);
> +			if (xspi->rxbuf)
> +				*xspi->rxbuf++ = data;
> +
> +			xspi->requested_bytes--;
> +			trans_cnt--;
> +		}
> +
> +		if (xspi->remaining_bytes) {
> +			/* There is more data to send */
> +			cdns_spi_fill_tx_fifo(xspi);
> +		} else {
> +			/* Transfer is completed */
> +			cdns_spi_write(xspi, CDNS_SPI_IDR_OFFSET,
> +				       CDNS_SPI_IXR_DEFAULT_MASK);
> +			spi_finalize_current_transfer(master);
> +		}
> +		status = IRQ_HANDLED;
> +	}
> +
> +	return status;
> +}
> +
> +/**
> + * cdns_transfer_one - Initiates the SPI transfer
> + * @master:	Pointer to spi_master structure
> + * @spi:	Pointer to the spi_device structure
> + * @transfer:	Pointer to the spi_transfer structure which provides
> + *		information about next transfer parameters
> + *
> + * This function fills the TX FIFO, starts the SPI transfer and
> + * returns a positive transfer count so that core will wait for completion.
> + *
> + * Return:	Number of bytes transferred in the last transfer
> + */
> +static int cdns_transfer_one(struct spi_master *master,
> +			     struct spi_device *spi,
> +			     struct spi_transfer *transfer)
> +{
> +	struct cdns_spi *xspi = spi_master_get_devdata(master);
> +
> +	xspi->txbuf = transfer->tx_buf;
> +	xspi->rxbuf = transfer->rx_buf;
> +	xspi->remaining_bytes = transfer->len;
> +	xspi->requested_bytes = transfer->len;
> +
> +	cdns_spi_setup_transfer(spi, transfer);
> +
> +	cdns_spi_fill_tx_fifo(xspi);
> +
> +	cdns_spi_write(xspi, CDNS_SPI_IER_OFFSET,
> +		       CDNS_SPI_IXR_DEFAULT_MASK);
> +	return transfer->len;
> +}
> +
> +/**
> + * cdns_prepare_transfer_hardware - Prepares hardware for transfer.
> + * @master:	Pointer to the spi_master structure which provides
> + *		information about the controller.
> + *
> + * This function enables SPI master controller.
> + *
> + * Return:	0 always
> + */
> +static int cdns_prepare_transfer_hardware(struct spi_master *master)
> +{
> +	struct cdns_spi *xspi = spi_master_get_devdata(master);
> +
> +	clk_enable(xspi->ref_clk);
> +	clk_enable(xspi->pclk);
> +	cdns_spi_write(xspi, CDNS_SPI_ER_OFFSET,
> +		       CDNS_SPI_ER_ENABLE_MASK);
> +
> +	return 0;
> +}
> +
> +/**
> + * cdns_unprepare_transfer_hardware - Relaxes hardware after transfer
> + * @master:	Pointer to the spi_master structure which provides
> + *		information about the controller.
> + *
> + * This function disables the SPI master controller.
> + *
> + * Return:	0 always
> + */
> +static int cdns_unprepare_transfer_hardware(struct spi_master *master)
> +{
> +	struct cdns_spi *xspi = spi_master_get_devdata(master);
> +
> +	cdns_spi_write(xspi, CDNS_SPI_ER_OFFSET,
> +		       CDNS_SPI_ER_DISABLE_MASK);
> +	clk_disable(xspi->ref_clk);
> +	clk_disable(xspi->pclk);
> +
> +	return 0;
> +}
> +
> +/**
> + * cdns_spi_probe - Probe method for the SPI driver
> + * @pdev:	Pointer to the platform_device structure
> + *
> + * This function initializes the driver data structures and the hardware.
> + *
> + * Return:	0 on success and error value on error
> + */
> +static int cdns_spi_probe(struct platform_device *pdev)
> +{
> +	int ret = 0, irq;
> +	struct spi_master *master;
> +	struct cdns_spi *xspi;
> +	struct resource *res;
> +
> +	master = spi_alloc_master(&pdev->dev, sizeof(*xspi));
> +	if (master == NULL)
> +		return -ENOMEM;
> +
> +	xspi = spi_master_get_devdata(master);
> +	master->dev.of_node = pdev->dev.of_node;
> +	platform_set_drvdata(pdev, master);
> +
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	xspi->regs = devm_ioremap_resource(&pdev->dev, res);
> +	if (IS_ERR(xspi->regs)) {
> +		ret = PTR_ERR(xspi->regs);
> +		goto remove_master;
> +	}
> +
> +	xspi->pclk = devm_clk_get(&pdev->dev, "pclk");
> +	if (IS_ERR(xspi->pclk)) {
> +		dev_err(&pdev->dev, "pclk clock not found.\n");
> +		ret = PTR_ERR(xspi->pclk);
> +		goto remove_master;
> +	}
> +
> +	xspi->ref_clk = devm_clk_get(&pdev->dev, "ref_clk");
> +	if (IS_ERR(xspi->ref_clk)) {
> +		dev_err(&pdev->dev, "ref_clk clock not found.\n");
> +		ret = PTR_ERR(xspi->ref_clk);
> +		goto remove_master;
> +	}
> +
> +	ret = clk_prepare_enable(xspi->pclk);
> +	if (ret) {
> +		dev_err(&pdev->dev, "Unable to enable APB clock.\n");
> +		goto remove_master;
> +	}
> +
> +	ret = clk_prepare_enable(xspi->ref_clk);
> +	if (ret) {
> +		dev_err(&pdev->dev, "Unable to enable device clock.\n");
> +		goto clk_dis_apb;
> +	}
> +
> +	/* SPI controller initializations */
> +	cdns_spi_init_hw(xspi);
> +
> +	irq = platform_get_irq(pdev, 0);
> +	if (irq <= 0) {
> +		ret = -ENXIO;
> +		dev_err(&pdev->dev, "irq number is invalid\n");
> +		goto remove_master;
> +	}
> +
> +	ret = devm_request_irq(&pdev->dev, irq, cdns_spi_irq,
> +			       0, pdev->name, master);
> +	if (ret != 0) {
> +		ret = -ENXIO;
> +		dev_err(&pdev->dev, "request_irq failed\n");
> +		goto remove_master;
> +	}
> +
> +	ret = of_property_read_u16(pdev->dev.of_node, "num-cs",
> +				   &master->num_chipselect);
> +	if (ret < 0)
> +		master->num_chipselect = CDNS_SPI_DEFAULT_NUM_CS;
> +
> +	master->setup = cdns_spi_setup;
> +	master->prepare_transfer_hardware = cdns_prepare_transfer_hardware;
> +	master->transfer_one = cdns_transfer_one;
> +	master->unprepare_transfer_hardware = cdns_unprepare_transfer_hardware;
> +	master->set_cs = cdns_spi_chipselect;
> +	master->mode_bits = SPI_CPOL | SPI_CPHA;
> +
> +	/* Set to default valid value */
> +	master->max_speed_hz = clk_get_rate(xspi->ref_clk) / 4;
> +	xspi->speed_hz = master->max_speed_hz;
> +
> +	master->bits_per_word_mask = SPI_BPW_MASK(8);
> +
> +	xspi->driver_state = CDNS_SPI_DRIVER_STATE_READY;
> +
> +	ret = spi_register_master(master);
> +	if (ret) {
> +		dev_err(&pdev->dev, "spi_register_master failed\n");
> +		goto clk_dis_all;
> +	}
> +
> +	return ret;
> +
> +clk_dis_all:
> +	clk_disable_unprepare(xspi->ref_clk);
> +clk_dis_apb:
> +	clk_disable_unprepare(xspi->pclk);
> +remove_master:
> +	spi_master_put(master);
> +	return ret;
> +}
> +
> +/**
> + * cdns_spi_remove - Remove method for the SPI driver
> + * @pdev:	Pointer to the platform_device structure
> + *
> + * This function is called if a device is physically removed from the system or
> + * if the driver module is being unloaded. It frees all resources allocated to
> + * the device.
> + *
> + * Return:	0 on success and error value on error
> + */
> +static int cdns_spi_remove(struct platform_device *pdev)
> +{
> +	struct spi_master *master = platform_get_drvdata(pdev);
> +	struct cdns_spi *xspi = spi_master_get_devdata(master);
> +
> +	cdns_spi_write(xspi, CDNS_SPI_ER_OFFSET,
> +		       CDNS_SPI_ER_DISABLE_MASK);
> +
> +	clk_disable_unprepare(xspi->ref_clk);
> +	clk_disable_unprepare(xspi->pclk);
> +
> +	spi_unregister_master(master);
> +
> +	return 0;
> +}
> +
> +/**
> + * cdns_spi_suspend - Suspend method for the SPI driver
> + * @dev:	Address of the platform_device structure
> + *
> + * This function disables the SPI controller and
> + * changes the driver state to "suspend"
> + *
> + * Return:	Always 0
> + */
> +static int __maybe_unused cdns_spi_suspend(struct device *dev)
> +{
> +	struct platform_device *pdev = container_of(dev,
> +			struct platform_device, dev);
> +	struct spi_master *master = platform_get_drvdata(pdev);
> +
> +	spi_master_suspend(master);
> +
> +	cdns_unprepare_transfer_hardware(master);
> +
> +	return 0;
> +}
> +
> +/**
> + * cdns_spi_resume - Resume method for the SPI driver
> + * @dev:	Address of the platform_device structure
> + *
> + * This function changes the driver state to "ready"
> + *
> + * Return:	0 on success and error value on error
> + */
> +static int __maybe_unused cdns_spi_resume(struct device *dev)
> +{
> +	struct platform_device *pdev = container_of(dev,
> +			struct platform_device, dev);
> +	struct spi_master *master = platform_get_drvdata(pdev);
> +	struct cdns_spi *xspi = spi_master_get_devdata(master);
> +	int ret = 0;
> +
> +	ret = clk_enable(xspi->pclk);
> +	if (ret) {
> +		dev_err(dev, "Cannot enable APB clock.\n");
> +		return ret;
> +	}
> +
> +	ret = clk_enable(xspi->ref_clk);
> +	if (ret) {
> +		dev_err(dev, "Cannot enable device clock.\n");
> +		clk_disable(xspi->pclk);
> +		return ret;
> +	}
> +	spi_master_resume(master);
> +
> +	return 0;
> +}
> +
> +static SIMPLE_DEV_PM_OPS(cdns_spi_dev_pm_ops, cdns_spi_suspend,
> +			 cdns_spi_resume);
> +
> +static struct of_device_id cdns_spi_of_match[] = {
> +	{ .compatible = "xlnx,zynq-spi-r1p6" },
> +	{ .compatible = "cdns,spi-r1p6" },
> +	{ /* end of table */ }
> +};
> +MODULE_DEVICE_TABLE(of, cdns_spi_of_match);
> +
> +/* cdns_spi_driver - This structure defines the SPI subsystem platform driver */
> +static struct platform_driver cdns_spi_driver = {
> +	.probe	= cdns_spi_probe,
> +	.remove	= cdns_spi_remove,
> +	.driver = {
> +		.name = CDNS_SPI_NAME,
> +		.owner = THIS_MODULE,
> +		.of_match_table = cdns_spi_of_match,
> +		.pm = &cdns_spi_dev_pm_ops,
> +	},
> +};
> +
> +module_platform_driver(cdns_spi_driver);
> +
> +MODULE_AUTHOR("Xilinx, Inc.");
> +MODULE_DESCRIPTION("Cadence SPI driver");
> +MODULE_LICENSE("GPL");
> -- 
> 1.7.9.5
> 
> 

Attachment: signature.asc
Description: Digital signature


[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux