Re: [PATCH 2/3] mtd: rawnand: sunxi: Add DMA support for sun8i

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Boris,

Boris Brezillon <boris.brezillon@xxxxxxxxxxxxx> wrote on Mon, 15 Apr
2019 09:14:20 +0200:

> On Mon, 15 Apr 2019 08:58:59 +0200
> Miquel Raynal <miquel.raynal@xxxxxxxxxxx> wrote:
> 
> > Hi Boris,
> > 
> > Boris Brezillon <boris.brezillon@xxxxxxxxxxxxx> wrote on Sun, 14 Apr
> > 2019 11:05:49 +0200:
> >   
> > > On Thu,  4 Apr 2019 18:21:10 +0200
> > > Miquel Raynal <miquel.raynal@xxxxxxxxxxx> wrote:
> > >     
> > > > Allwinner NAND controllers can make use of DMA to enhance the I/O
> > > > throughput thanks to ECC pipelining. DMA handling with sun8i NAND IP
> > > > is a bit different than with the older SoCs, hence the introduction of
> > > > a new compatible to handle:
> > > > * the differences between register offsets,
> > > > * the burst length change from 4 to minimum 8,
> > > > * drive SRAM accesses through the AHB bus instead of the MBUS.      
> > > 
> > > Hm, now that you know MBUS accesses are working fine (IIRC, that's what
> > > you used for the SPL DMA-based implementation), why not directly use
> > > MBUS accesses on A33? I mean, it's likely faster than going through
> > > the DMA engine (which is shared by several IPs), and AFAIR, the MBUS
> > > setup is pretty simple.    
> > 
> > Because all the driver is already in shape to use the external DMA
> > engine and it was very easy and quick (have a look at the diff of the
> > v3) to use it again.  
> 
> Yes, I see that. I might be wrong but I'd expect the MDMA version to be
> just as simple as this one.
> 
> > 
> > However, the choice I am describing here is not DMA vs. MBUS (or MDMA),
> > it is MBUS vs. AHB, it is just about the bus that will access the SRAM
> > (this is what we have understood with Maxime from the datasheets and
> > the tests we have done).  
> 
> Yes, sorry, I meant MDMA vs shared DMA engine, but I guess MBUS is only
> used through MDMA accesses anyway, right?

I have no proof that I actually used MBUS, but there is a bit which can
be set to use MBUS to access the SRAM even when not using MDMA. In this
case, MBUS payload length had to be filled or the operation would not
succeed. However when using AHB, there is no need for this extra
configuration. That's why I decided to use the AHB.

> 
> > For this choice, we tested with both buses: no
> > throughput change so we think that it is not a bottleneck anyway.  
> 
> Well, you'd need to test with a lot of traffic going through the DMA
> engine to check if that makes a difference.

True, I probably didn't stressed the platform enough to see the
difference.

> 
> Anyway, it was just a suggestion, keep it like that if you think using
> MDMA is not worthwhile.


Thanks,
Miquèl



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux