From: David Lechner <david@xxxxxxxxxxxxxx>
This adds a cpu node and operating points to the common da850.dtsi file.
Additionally, a regulator is added to the LEGO EV3 board along with
some board-specific CPU configuration.
Regulators need to be hooked up on other boards to get them working.
Signed-off-by: David Lechner <david@xxxxxxxxxxxxxx>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@xxxxxxxxxxxx>
---
arch/arm/boot/dts/da850-lcdk.dts | 31 +++++++++++++++
arch/arm/boot/dts/da850-lego-ev3.dts | 30 +++++++++++++++
arch/arm/boot/dts/da850.dtsi | 56 ++++++++++++++++++++++++++++
3 files changed, 117 insertions(+)
diff --git a/arch/arm/boot/dts/da850-lcdk.dts b/arch/arm/boot/dts/da850-lcdk.dts
index 26f453dc8370..f29ed9010812 100644
--- a/arch/arm/boot/dts/da850-lcdk.dts
+++ b/arch/arm/boot/dts/da850-lcdk.dts
@@ -155,12 +155,43 @@
};
};
};
+
+ cvdd: regulator0 {
+ compatible = "regulator-fixed";
+ regulator-name = "cvdd";
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
};
&ref_clk {
clock-frequency = <24000000>;
};
+&cpu {
+ cpu-supply = <&cvdd>;
+};
+
+/* LCDK has a fixed CVDD of 1.3V, so only op points >= 300MHz are valid */
+
+&opp_100 {
+ status = "disabled";
+};
+
+&opp_200 {
+ status = "disabled";
+};
+
+&opp_375 {
+ status = "okay";
+};
+
+&opp_456 {
+ status = "okay";
+};
+
&pmx_core {
status = "okay";
diff --git a/arch/arm/boot/dts/da850-lego-ev3.dts b/arch/arm/boot/dts/da850-lego-ev3.dts
index 66fcadf0ba91..553717f84483 100644
--- a/arch/arm/boot/dts/da850-lego-ev3.dts
+++ b/arch/arm/boot/dts/da850-lego-ev3.dts
@@ -125,6 +125,15 @@
amp-supply = <&>;
};
+ cvdd: regulator0 {
+ compatible = "regulator-fixed";
+ regulator-name = "cvdd";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
/*
* This is a 5V current limiting regulator that is shared by USB,
* the sensor (input) ports, the motor (output) ports and the A/DC.
@@ -204,6 +213,27 @@
clock-frequency = <24000000>;
};
+&cpu {
+ cpu-supply = <&cvdd>;
+};
+
+/* since we have a fixed regulator, we can't run at these points */
+&opp_100 {
+ status = "disabled";
+};
+
+&opp_200 {
+ status = "disabled";
+};
+
+/*
+ * The SoC is actually the 456MHz version, but because of the fixed regulator
+ * This is the fastest we can go.
+ */
+&opp_375 {
+ status = "okay";
+};
+
&pmx_core {
status = "okay";
diff --git a/arch/arm/boot/dts/da850.dtsi b/arch/arm/boot/dts/da850.dtsi
index 559659b399d0..ee61d1253b58 100644
--- a/arch/arm/boot/dts/da850.dtsi
+++ b/arch/arm/boot/dts/da850.dtsi
@@ -20,6 +20,62 @@
reg = <0xc0000000 0x0>;
};
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu: cpu@0 {
+ compatible = "arm,arm926ej-s";
+ device_type = "cpu";
+ reg = <0>;
+ clocks = <&psc0 14>;
+ operating-points-v2 = <&opp_table>;
+ };
+ };
+
+ opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp_100: opp100-100000000 {
+ opp-hz = /bits/ 64 <100000000>;
+ opp-microvolt = <1000000 950000 1050000>;
+ };
+
+ opp_200: opp110-200000000 {
+ opp-hz = /bits/ 64 <200000000>;
+ opp-microvolt = <1100000 1050000 1160000>;
+ };
+
+ opp_300: opp120-300000000 {
+ opp-hz = /bits/ 64 <300000000>;
+ opp-microvolt = <1200000 1140000 1320000>;
+ };
+
+ /*
+ * Original silicon was 300MHz max, so higher frequencies
+ * need to be enabled on a per-board basis if the chip is
+ * capable.
+ */
+
+ opp_375: opp120-375000000 {
+ status = "disabled";
+ opp-hz = /bits/ 64 <375000000>;
+ opp-microvolt = <1200000 1140000 1320000>;
+ };
+
+ opp_415: opp130-415000000 {
+ status = "disabled";
+ opp-hz = /bits/ 64 <415000000>;
+ opp-microvolt = <1300000 1250000 1350000>;
+ };
+
+ opp_456: opp130-456000000 {
+ status = "disabled";
+ opp-hz = /bits/ 64 <456000000>;
+ opp-microvolt = <1300000 1250000 1350000>;
+ };
+ };
+
arm {
#address-cells = <1>;
#size-cells = <1>;
--
2.21.0
