Re: [PATCH 05/10] dt-bindings: PCI: tegra: Add device tree support for T194

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 3/27/2019 3:40 PM, Jon Hunter wrote:

On 26/03/2019 15:13, Vidya Sagar wrote:
Add support for Tegra194 PCIe controllers. These controllers are based
on Synopsys DesignWare core IP.

Signed-off-by: Vidya Sagar <vidyas@xxxxxxxxxx>
---
  .../bindings/pci/nvidia,tegra194-pcie.txt          | 209 +++++++++++++++++++++
  .../devicetree/bindings/phy/phy-tegra194-p2u.txt   |  34 ++++
  2 files changed, 243 insertions(+)
  create mode 100644 Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt
  create mode 100644 Documentation/devicetree/bindings/phy/phy-tegra194-p2u.txt

diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt
new file mode 100644
index 000000000000..31527283a0cd
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt
@@ -0,0 +1,209 @@
+NVIDIA Tegra PCIe controller (Synopsys DesignWare Core based)
+
+This PCIe host controller is based on the Synopsis Designware PCIe IP
+and thus inherits all the common properties defined in designware-pcie.txt.
+
+Required properties:
+- compatible: For Tegra19x, must contain "nvidia,tegra194-pcie".
+- device_type: Must be "pci"
+- reg: A list of physical base address and length for each set of controller
+  registers. Must contain an entry for each entry in the reg-names property.
+- reg-names: Must include the following entries:
+  "appl": Controller's application logic registers
+  "window1": This is the aperture of controller available under 4GB boundary
+             (i.e. within 32-bit space). This aperture is typically used for
+             accessing config space of root port itself and also the connected
+             endpoints (by appropriately programming internal Address
+             Translation Unit's (iATU) out bound region) and also to map
+             prefetchable/non-prefetchable BARs.
+  "config": As per the definition in designware-pcie.txt
+  "atu_dma": iATU and DMA register. This is where the iATU (internal Address
+             Translation Unit) registers of the PCIe core are made available
+             fow SW access.
+  "dbi": The aperture where root port's own configuration registers are
+         available
+  "window2": This is the larger (compared to window1) aperture available above
+             4GB boundary (i.e. in 64-bit space). This is typically used for
+             mapping prefetchable/non-prefetchable BARs of endpoints
+- interrupts: A list of interrupt outputs of the controller. Must contain an
+  entry for each entry in the interrupt-names property.
+- interrupt-names: Must include the following entries:
+  "intr": The Tegra interrupt that is asserted for controller interrupts
+  "msi": The Tegra interrupt that is asserted when an MSI is received
+- bus-range: Range of bus numbers associated with this controller
+- #address-cells: Address representation for root ports (must be 3)
+  - cell 0 specifies the bus and device numbers of the root port:
+    [23:16]: bus number
+    [15:11]: device number
+  - cell 1 denotes the upper 32 address bits and should be 0
+  - cell 2 contains the lower 32 address bits and is used to translate to the
+    CPU address space
+- #size-cells: Size representation for root ports (must be 2)
+- ranges: Describes the translation of addresses for root ports and standard
+  PCI regions. The entries must be 7 cells each, where the first three cells
+  correspond to the address as described for the #address-cells property
+  above, the fourth and fifth cells are for the physical CPU address to
+  translate to and the sixth and seventh cells are as described for the
+  #size-cells property above.
+  - Entries setup the mapping for the standard I/O, memory and
+    prefetchable PCI regions. The first cell determines the type of region
+    that is setup:
+    - 0x81000000: I/O memory region
+    - 0x82000000: non-prefetchable memory region
+    - 0xc2000000: prefetchable memory region
+  Please refer to the standard PCI bus binding document for a more detailed
+  explanation.
+- #interrupt-cells: Size representation for interrupts (must be 1)
+- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties
+  Please refer to the standard PCI bus binding document for a more detailed
+  explanation.
+- clocks: Must contain an entry for each entry in clock-names.
+  See ../clocks/clock-bindings.txt for details.
+- clock-names: Must include the following entries:
+  - core_clk
+- resets: Must contain an entry for each entry in reset-names.
+  See ../reset/reset.txt for details.
+- reset-names: Must include the following entries:
+  - core_apb_rst
+  - core_rst
+- phys: Must contain a phandle to P2U PHY for each entry in phy-names.
+- phy-names: Must include an entry for each active lane.
+  "pcie-p2u-N": where N ranges from 0 to one less than the total number of lanes
+- Controller dependent register offsets
+  - nvidia,event-cntr-ctrl: EVENT_COUNTER_CONTROL reg offset
+      0x168 - FPGA
+      0x1a8 - C1, C2 and C3
+      0x1c4 - C4
+      0x1d8 - C0 and C5
+  - nvidia,event-cntr-data: EVENT_COUNTER_DATA reg offset
+      0x16c - FPGA
+      0x1ac - C1, C2 and C3
+      0x1c8 - C4
+      0x1dc - C0 and C5
+- nvidia,controller-id : Controller specific ID
+      0x0 - C0
+      0x1 - C1
+      0x2 - C2
+      0x3 - C3
+      0x4 - C4
+      0x5 - C5
+- vddio-pex-ctl-supply: Regulator supply for PCIe side band signals

I don't see any power-domains listed here. We should have these for T194
right?
Thanks for catching this.
Yes. PCIe uses power-domains and I'll add that in the future patch.


Cheers
Jon





[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux