Hi Marcel,
On 11/03/2019 16:41, Marcel Holtmann wrote:
Hi David,
This patch is an outline for bluetooth on the ASUS Tinker Board (S).
Bluetooth is provided my RTL8723BS on these machine, and this is wired
into UART0.
Here this is performed as a SerDev device.
Now as presented, this does not give functioning bluetooth. The
updates needed to the device driver:
https://www.spinics.net/lists/linux-bluetooth/msg78661.html
Haven't yet been accepted. So this device tree hook doesn't yet have
"realtek,rtl8723bs-bt" compatible flag.
It is however still submitted as a patch, as it sets the UART up
correctly. And so basic communciation can be had with the device. This
has been confirmed by Tony McKahan @ Armbian, in particular that the
CTS/RTS is needed.
When Vasily patch is accepted, this will be added as a minor patch on
top of this patch; as this patch gives the pins needed.
The one oddity, is the RESET pin, it is labeled this way on the
schematic. However the hci_h5.c driver calls this ENABLE. Here we have
stuck with the schematic name.
Signed-off-by: David Summers <beagleboard@xxxxxxxxxxxxxxxxxxx>
---
arch/arm/boot/dts/rk3288-tinker.dtsi | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/arch/arm/boot/dts/rk3288-tinker.dtsi b/arch/arm/boot/dts/rk3288-tinker.dtsi
index 0ffab1b7c940..d29f5b34d7e6 100644
--- a/arch/arm/boot/dts/rk3288-tinker.dtsi
+++ b/arch/arm/boot/dts/rk3288-tinker.dtsi
@@ -486,6 +486,17 @@
&uart0 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_xfer>, <&uart0_cts>, <&uart0_rts>;
+
+ bluetooth {
+ clocks = <&rk808 RK808_CLKOUT1>;
+ reset-gpios = <&gpio4 RK_PD5 GPIO_ACTIVE_HIGH>;
+ device-wake-gpios = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>;
+ host-wake-gpios = <&gpio4 RK_PD7 GPIO_ACTIVE_HIGH>;
+ vcc-18-supply = <&vcc_18>;
+ vcc-io-supply = <&vcc_io>;
+ };
};
I need an ACK from Rob for this and also you might want to send the whole series for me to review in full context.
Regards
Marcel
Yes happy to wait for ACK from Rob. Of the 3 patches done this is the
least urgent, as Bluetooth is currently non functioning on these
machines, so delay in this doesn't change the status quo. Patch 3 is
self standing, e.g. not applying it doesn't affect the other two.
However patch 3 probably has to be applied sequentially after patches
1&2 as all are on the single file.
Following on from Robs comments on last patch sent adding bluetooth,
I've made this one FAR more detailed. That said though the drivers for
bluetooth in this case doesn't use clock or supply ASAIK. Most things
are brought up by the wifi part of the device tree which was patch 2.
However adding to the bluetooth device tree as well, at least leaves the
option open to a user just loading bluetooth, and not wifi.
The one thing missing from this bluetooth device tree, is explaining
which pins need to be pulled to bring up the card. This is part be
design (the tinker board and rt8723bs both have bad public documentation
- so exact operation is hard to guess ...); but also because I couldn't
see a way of getting a SerDev device to pull pins on loading, unlike
sdio (used for wifi).
Full series:
Part 1 - device tree changes for sd card
Part 2 - adding wifi to the device tree
Part 3 - adding outline bluetooth
So are each fairly self standing. However if interested in parts 1 and 2
they can be found:
http://lists.infradead.org/pipermail/linux-rockchip/2019-March/023330.html
http://lists.infradead.org/pipermail/linux-rockchip/2019-March/023331.html
Regards, and yes happy to wait and see what Rob has to say.
David.
