[PATCH v5 5/5] i2c: mediatek: Add i2c support for MediaTek MT8183

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Add i2c compatible for MT8183. Compare to MT2712 i2c controller,
MT8183 has different register offsets. Ltiming_reg is added to
adjust low width of SCL. Arb clock and dma_sync are needed.

Signed-off-by: Qii Wang <qii.wang@xxxxxxxxxxxx>
---
 drivers/i2c/busses/i2c-mt65xx.c |   53 +++++++++++++++++++++++++++++++++++++--
 1 file changed, 51 insertions(+), 2 deletions(-)

diff --git a/drivers/i2c/busses/i2c-mt65xx.c b/drivers/i2c/busses/i2c-mt65xx.c
index 75d88e1..82eedbd 100644
--- a/drivers/i2c/busses/i2c-mt65xx.c
+++ b/drivers/i2c/busses/i2c-mt65xx.c
@@ -133,6 +133,8 @@ enum I2C_REGS_OFFSET {
 	OFFSET_DEBUGCTRL,
 	OFFSET_TRANSFER_LEN_AUX,
 	OFFSET_CLOCK_DIV,
+	/* MT8183 only regs */
+	OFFSET_LTIMING,
 };
 
 static const u16 mt_i2c_regs_v1[] = {
@@ -162,6 +164,32 @@ enum I2C_REGS_OFFSET {
 	[OFFSET_CLOCK_DIV] = 0x70,
 };
 
+static const u16 mt_i2c_regs_v2[] = {
+	[OFFSET_DATA_PORT] = 0x0,
+	[OFFSET_SLAVE_ADDR] = 0x4,
+	[OFFSET_INTR_MASK] = 0x8,
+	[OFFSET_INTR_STAT] = 0xc,
+	[OFFSET_CONTROL] = 0x10,
+	[OFFSET_TRANSFER_LEN] = 0x14,
+	[OFFSET_TRANSAC_LEN] = 0x18,
+	[OFFSET_DELAY_LEN] = 0x1c,
+	[OFFSET_TIMING] = 0x20,
+	[OFFSET_START] = 0x24,
+	[OFFSET_EXT_CONF] = 0x28,
+	[OFFSET_LTIMING] = 0x2c,
+	[OFFSET_HS] = 0x30,
+	[OFFSET_IO_CONFIG] = 0x34,
+	[OFFSET_FIFO_ADDR_CLR] = 0x38,
+	[OFFSET_TRANSFER_LEN_AUX] = 0x44,
+	[OFFSET_CLOCK_DIV] = 0x48,
+	[OFFSET_SOFTRESET] = 0x50,
+	[OFFSET_DEBUGSTAT] = 0xe0,
+	[OFFSET_DEBUGCTRL] = 0xe8,
+	[OFFSET_FIFO_STAT] = 0xf4,
+	[OFFSET_FIFO_THRESH] = 0xf8,
+	[OFFSET_DCM_EN] = 0xf88,
+};
+
 struct mtk_i2c_compatible {
 	const struct i2c_adapter_quirks *quirks;
 	const u16 *regs;
@@ -195,6 +223,7 @@ struct mtk_i2c {
 	enum mtk_trans_op op;
 	u16 timing_reg;
 	u16 high_speed_reg;
+	u16 ltiming_reg;
 	unsigned char auto_restart;
 	bool ignore_restart_irq;
 	const struct mtk_i2c_compatible *dev_comp;
@@ -271,12 +300,24 @@ struct mtk_i2c {
 	.dma_sync = 0,
 };
 
+static const struct mtk_i2c_compatible mt8183_compat = {
+	.regs = mt_i2c_regs_v2,
+	.pmic_i2c = 0,
+	.dcm = 0,
+	.auto_restart = 1,
+	.aux_len_reg = 1,
+	.support_33bits = 1,
+	.timing_adjust = 1,
+	.dma_sync = 1,
+};
+
 static const struct of_device_id mtk_i2c_of_match[] = {
 	{ .compatible = "mediatek,mt2712-i2c", .data = &mt2712_compat },
 	{ .compatible = "mediatek,mt6577-i2c", .data = &mt6577_compat },
 	{ .compatible = "mediatek,mt6589-i2c", .data = &mt6589_compat },
 	{ .compatible = "mediatek,mt7622-i2c", .data = &mt7622_compat },
 	{ .compatible = "mediatek,mt8173-i2c", .data = &mt8173_compat },
+	{ .compatible = "mediatek,mt8183-i2c", .data = &mt8183_compat },
 	{}
 };
 MODULE_DEVICE_TABLE(of, mtk_i2c_of_match);
@@ -361,6 +402,8 @@ static void mtk_i2c_init_hw(struct mtk_i2c *i2c)
 
 	mtk_i2c_writew(i2c, i2c->timing_reg, OFFSET_TIMING);
 	mtk_i2c_writew(i2c, i2c->high_speed_reg, OFFSET_HS);
+	if (i2c->dev_comp->regs == mt_i2c_regs_v2)
+		mtk_i2c_writew(i2c, i2c->ltiming_reg, OFFSET_LTIMING);
 
 	/* If use i2c pin from PMIC mt6397 side, need set PATH_DIR first */
 	if (i2c->have_pmic)
@@ -460,6 +503,8 @@ static int mtk_i2c_set_speed(struct mtk_i2c *i2c, unsigned int parent_clk)
 	unsigned int clk_src;
 	unsigned int step_cnt;
 	unsigned int sample_cnt;
+	unsigned int l_step_cnt;
+	unsigned int l_sample_cnt;
 	unsigned int target_speed;
 	int ret;
 
@@ -469,11 +514,11 @@ static int mtk_i2c_set_speed(struct mtk_i2c *i2c, unsigned int parent_clk)
 	if (target_speed > MAX_FS_MODE_SPEED) {
 		/* Set master code speed register */
 		ret = mtk_i2c_calculate_speed(i2c, clk_src, MAX_FS_MODE_SPEED,
-					      &step_cnt, &sample_cnt);
+					      &l_step_cnt, &l_sample_cnt);
 		if (ret < 0)
 			return ret;
 
-		i2c->timing_reg = (sample_cnt << 8) | step_cnt;
+		i2c->timing_reg = (l_sample_cnt << 8) | l_step_cnt;
 
 		/* Set the high speed mode register */
 		ret = mtk_i2c_calculate_speed(i2c, clk_src, target_speed,
@@ -483,6 +528,8 @@ static int mtk_i2c_set_speed(struct mtk_i2c *i2c, unsigned int parent_clk)
 
 		i2c->high_speed_reg = I2C_TIME_DEFAULT_VALUE |
 			(sample_cnt << 12) | (step_cnt << 8);
+		i2c->ltiming_reg = (l_sample_cnt << 6) | l_step_cnt |
+				   (sample_cnt << 12) | (step_cnt << 9);
 	} else {
 		ret = mtk_i2c_calculate_speed(i2c, clk_src, target_speed,
 					      &step_cnt, &sample_cnt);
@@ -493,6 +540,8 @@ static int mtk_i2c_set_speed(struct mtk_i2c *i2c, unsigned int parent_clk)
 
 		/* Disable the high speed transaction */
 		i2c->high_speed_reg = I2C_TIME_CLR_VALUE;
+
+		i2c->ltiming_reg = (sample_cnt << 6) | step_cnt;
 	}
 
 	return 0;
-- 
1.7.9.5




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux