Re: [PATCH 3/8] dt-bindings: net: bluetooth: Add rtl8723bs-bluetooth

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Vasily,

Just catching up with this series - good that you are doing it. We need it for users on ArchLinux ARM!

On question though, what is "firmware-postfix" used for? I see in the documentation, that it points to the board name. But can't see where else it is used.

Is there a need to have the board name?

Anyway good work.

David.

On 18/02/2019 22:28, Vasily Khoruzhick wrote:
On Mon, Feb 18, 2019 at 2:08 PM Stefan Wahren <stefan.wahren@xxxxxxxx> wrote:
Hi Vasily,
Hi Stefan,

Vasily Khoruzhick <anarsoul@xxxxxxxxx> hat am 18. Februar 2019 um 22:24 geschrieben:


On Mon, Feb 18, 2019 at 1:10 PM Rob Herring <robh@xxxxxxxxxx> wrote:
On Fri, Jan 18, 2019 at 09:02:27AM -0800, Vasily Khoruzhick wrote:
Add binding document for bluetooth part of RTL8723BS/RTL8723CS

Signed-off-by: Vasily Khoruzhick <anarsoul@xxxxxxxxx>
---
  .../bindings/net/rtl8723bs-bluetooth.txt      | 35 +++++++++++++++++++
  1 file changed, 35 insertions(+)
  create mode 100644 Documentation/devicetree/bindings/net/rtl8723bs-bluetooth.txt

diff --git a/Documentation/devicetree/bindings/net/rtl8723bs-bluetooth.txt b/Documentation/devicetree/bindings/net/rtl8723bs-bluetooth.txt
new file mode 100644
index 000000000000..8357f242ae4c
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/rtl8723bs-bluetooth.txt
@@ -0,0 +1,35 @@
+RTL8723BS/RTL8723CS Bluetooth
+---------------------
+
+RTL8723CS/RTL8723CS is WiFi + BT chip. WiFi part is connected over SDIO, while
+BT is connected over serial. It speaks H5 protocol with few extra commands
+to upload firmware and change module speed.
+
+Required properties:
+
+ - compatible: should be one of the following:
+   * "realtek,rtl8723bs-bt"
+   * "realtek,rtl8723cs-bt"
+Optional properties:
+
+ - device-wake-gpios: GPIO specifier, used to wakeup the BT module (active high)
+ - enable-gpios: GPIO specifier, used to enable the BT module (active high)
+ - host-wake-gpios: GPIO specifier, used to wakeup the host processor (active high)
+ - firmware-postfix: firmware postfix to be used for firmware config
sorry, i didn't noticed your great series before. David and i working at the same stuff but for the Asus Tinker Board.

I created a similiar yet untested patch version for hci_h5 [1]. Maybe it's useful.
Looks good to me, but you may need to add firmware-postfix.

Just a comment about the binding. It's really necessary to add the reset-gpio? Can't we use the enable-gpio with inverse polarity for this?
Yes, we can use enable-gpio instead of reset-gpio on pine64 and pinebook.

Stefan





[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux