These two patches try to add initial NAND driver support for Amlogic Meson SoCs, current it has been tested on GXL(p212) and AXG(s400) platform. Changes since V6 at [7] - use timings->tBERS_max as the maximum time out, delete NFC_CMD_RB_TIMEOUT - fix nand_rw_cmd and support small block flash and which row address less than 3 - fix coding style - replace readl/writel_* with readl/writel_relaxed* - delete ECC_SET_PROTECTED_OOB_BYTE and ECC_GET_PROTECTED_OOB_BYTE - implement dma access for read_buf and write_buf, more efficient. - delete waiting dma finish in write process and let NAND_CMD_PAGEPROG and RB command go on queuing - add waiting the completed flag of last ecc page be set, for more strict Changes since v5 at [6]: - use instr->delay_ns in exec_op() to caculate the delay cycle - delete struct meson_nfc_info_format and use macros instead - delete "is_scramble" in struct meson_nfc_nand_chip - add WARN_ON_ONCE() for chip > MAX_CE_NUM - drop param *mtd* or struct *nfc* if param *nand exist - substitute set_data_oob and get_data_oob for prase_data_oob and format_data_oob - split timings caculating and setting timings - move info_buf and data_buf to struct meson_nfc_nand_chip Changes since v4 at [5]: - remove the initial default divider(CLK_DIV_MASK) in meson_nfc_clk_init() - dt-bindings: remove staus, add "rx" and "tx" clock, and node rename Changes since v3 at [4]: - remove partition table and some used props from dt-bindings Changes since v2 at [3]: - remove some hardcode time value, like twb - use dev wait R/B instead of nand_soft_waitrdy - implement nfc ecc init by ecc helper - rework nfc buffer init to register the maximun buffer when several chips - free nfc buffer when error and cleanup - add variable to teack all the already assigned CS lines - fix mtd->name use the first cs line only - remove dt "nand-enable-scrambler" and use NAND_NEED_SCRAMBLING instead. - move setuping ECC fileds after the identification phase - use nand_scan() and attach_chip() - check one event to return IRQ_NONE - delete cast when of_device_get_match_data - use nand_controller_init() helper - remove nfc driver complains when calling devm_ioremap_resource - clear irqs before setting up irq handler Changes since v1 at [1]: - adopt property amlogic,nand-enable-scrambler - thanks Martin - drop nand pins in DT - convert clk access to emmc clkc model - fix regiser field definition alignment - drop nand-user-mode - parse cs id from DT - rework n2m, m2n function - explain why insert two "IDLE" command - implement exec_op() - drop meson_nfc_get_nand_chip_dts() - release resource once error occur in meson_nfc_nand_chips_init(), - call nand_cleanup(nand) once mtd_device_register fail Items not addressed ( or confirmed ) in this version: - convert to ECC conf helper() - convert to dma coherent API - how to construct mtd->name [1] https://lkml.kernel.org/r/20180613161314.14894-1-yixun.lan@xxxxxxxxxxx [2] https://lkml.kernel.org/r/20180712211244.11428-1-yixun.lan@xxxxxxxxxxx [3] https://lkml.kernel.org/r/20180719094612.5833-1-yixun.lan@xxxxxxxxxxx [4] https://lkml.kernel.org/r/1536317831-58056-1-git-send-email-jianxin.pan@xxxxxxxxxxx/ [5] https://lore.kernel.org/r/1537433449-65213-2-git-send-email-jianxin.pan@xxxxxxxxxxx/ [6] https://lore.kernel.org/r/1539839345-14021-1-git-send-email-jianxin.pan@xxxxxxxxxxx [7] https://lore.kernel.org/r/1541090542-19618-1-git-send-email-jianxin.pan@xxxxxxxxxxx Liang Yang (2): dt-bindings: nand: meson: add Amlogic NAND controller driver mtd: rawnand: meson: add support for Amlogic NAND flash controller .../devicetree/bindings/mtd/amlogic,meson-nand.txt | 60 + drivers/mtd/nand/raw/Kconfig | 10 + drivers/mtd/nand/raw/Makefile | 1 + drivers/mtd/nand/raw/meson_nand.c | 1417 ++++++++++++++++++++ 4 files changed, 1488 insertions(+) create mode 100644 Documentation/devicetree/bindings/mtd/amlogic,meson-nand.txt create mode 100644 drivers/mtd/nand/raw/meson_nand.c -- 1.9.1
