The FSL QSPI driver will be moved to the SPI framework and it then
acts as a SPI controller. Therefore the subnodes need to set
spi-[rx/tx]-bus-width = <4>, so quad mode is used just as before.
Also the properties 'num-cs' and 'bus-num' were never read by the
driver and can be removed.
The property 'fsl,qspi-has-second-chip' is not needed anymore
and will be removed after the old driver was disabled to avoid
breaking fsl-ls1046a-rdb.dts.
Signed-off-by: Frieder Schrempf <frieder.schrempf@xxxxxxxxxx>
---
arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dts | 3 ++-
arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts | 4 ++--
arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts | 6 ++++--
arch/arm64/boot/dts/freescale/fsl-ls208xa-qds.dtsi | 4 ++++
4 files changed, 12 insertions(+), 5 deletions(-)
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dts
index dff3d64..8a50094 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dts
@@ -135,7 +135,6 @@
};
&qspi {
- bus-num = <0>;
status = "okay";
qflash0: s25fl128s@0 {
@@ -143,6 +142,8 @@
#address-cells = <1>;
#size-cells = <1>;
spi-max-frequency = <20000000>;
+ spi-rx-bus-width = <4>;
+ spi-tx-bus-width = <4>;
reg = <0>;
};
};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts
index e58a8ca..2f220ec 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts
@@ -163,8 +163,6 @@
};
&qspi {
- num-cs = <2>;
- bus-num = <0>;
status = "okay";
qflash0: s25fl128s@0 {
@@ -172,6 +170,8 @@
#address-cells = <1>;
#size-cells = <1>;
spi-max-frequency = <20000000>;
+ spi-rx-bus-width = <4>;
+ spi-tx-bus-width = <4>;
reg = <0>;
};
};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts
index a59b482..07c665c 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts
@@ -99,8 +99,6 @@
};
&qspi {
- num-cs = <2>;
- bus-num = <0>;
status = "okay";
qflash0: s25fs512s@0 {
@@ -108,6 +106,8 @@
#address-cells = <1>;
#size-cells = <1>;
spi-max-frequency = <20000000>;
+ spi-rx-bus-width = <4>;
+ spi-tx-bus-width = <4>;
reg = <0>;
};
@@ -116,6 +116,8 @@
#address-cells = <1>;
#size-cells = <1>;
spi-max-frequency = <20000000>;
+ spi-rx-bus-width = <4>;
+ spi-tx-bus-width = <4>;
reg = <1>;
};
};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls208xa-qds.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls208xa-qds.dtsi
index c11f52e..10d2fe0 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls208xa-qds.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls208xa-qds.dtsi
@@ -134,6 +134,8 @@
#size-cells = <1>;
compatible = "st,m25p80";
spi-max-frequency = <20000000>;
+ spi-rx-bus-width = <4>;
+ spi-tx-bus-width = <4>;
reg = <0>;
};
flash2: s25fl256s1@2 {
@@ -141,6 +143,8 @@
#size-cells = <1>;
compatible = "st,m25p80";
spi-max-frequency = <20000000>;
+ spi-rx-bus-width = <4>;
+ spi-tx-bus-width = <4>;
reg = <2>;
};
};
--
2.7.4
