From: Frieder Schrempf <frieder.schrempf@xxxxxxxxx>
Move the documentation of the old SPI NOR driver to the place of the new
SPI memory interface based driver.
Signed-off-by: Frieder Schrempf <frieder.schrempf@xxxxxxxxx>
---
.../devicetree/bindings/mtd/fsl-quadspi.txt | 65 --------------------
.../devicetree/bindings/spi/spi-fsl-qspi.txt | 65 ++++++++++++++++++++
2 files changed, 65 insertions(+), 65 deletions(-)
diff --git a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt b/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt
deleted file mode 100644
index 483e9cf..0000000
--- a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt
+++ /dev/null
@@ -1,65 +0,0 @@
-* Freescale Quad Serial Peripheral Interface(QuadSPI)
-
-Required properties:
- - compatible : Should be "fsl,vf610-qspi", "fsl,imx6sx-qspi",
- "fsl,imx7d-qspi", "fsl,imx6ul-qspi",
- "fsl,ls1021a-qspi"
- or
- "fsl,ls2080a-qspi" followed by "fsl,ls1021a-qspi",
- "fsl,ls1043a-qspi" followed by "fsl,ls1021a-qspi"
- - reg : the first contains the register location and length,
- the second contains the memory mapping address and length
- - reg-names: Should contain the reg names "QuadSPI" and "QuadSPI-memory"
- - interrupts : Should contain the interrupt for the device
- - clocks : The clocks needed by the QuadSPI controller
- - clock-names : Should contain the name of the clocks: "qspi_en" and "qspi".
-
-Optional properties:
- - fsl,qspi-has-second-chip: The controller has two buses, bus A and bus B.
- Each bus can be connected with two NOR flashes.
- Most of the time, each bus only has one NOR flash
- connected, this is the default case.
- But if there are two NOR flashes connected to the
- bus, you should enable this property.
- (Please check the board's schematic.)
- - big-endian : That means the IP register is big endian
-
-Example:
-
-qspi0: quadspi@40044000 {
- compatible = "fsl,vf610-qspi";
- reg = <0x40044000 0x1000>, <0x20000000 0x10000000>;
- reg-names = "QuadSPI", "QuadSPI-memory";
- interrupts = <0 24 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks VF610_CLK_QSPI0_EN>,
- <&clks VF610_CLK_QSPI0>;
- clock-names = "qspi_en", "qspi";
-
- flash0: s25fl128s@0 {
- ....
- };
-};
-
-Example showing the usage of two SPI NOR devices:
-
-&qspi2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_qspi2>;
- status = "okay";
-
- flash0: n25q256a@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "micron,n25q256a", "jedec,spi-nor";
- spi-max-frequency = <29000000>;
- reg = <0>;
- };
-
- flash1: n25q256a@1 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "micron,n25q256a", "jedec,spi-nor";
- spi-max-frequency = <29000000>;
- reg = <1>;
- };
-};
diff --git a/Documentation/devicetree/bindings/spi/spi-fsl-qspi.txt b/Documentation/devicetree/bindings/spi/spi-fsl-qspi.txt
new file mode 100644
index 0000000..483e9cf
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi-fsl-qspi.txt
@@ -0,0 +1,65 @@
+* Freescale Quad Serial Peripheral Interface(QuadSPI)
+
+Required properties:
+ - compatible : Should be "fsl,vf610-qspi", "fsl,imx6sx-qspi",
+ "fsl,imx7d-qspi", "fsl,imx6ul-qspi",
+ "fsl,ls1021a-qspi"
+ or
+ "fsl,ls2080a-qspi" followed by "fsl,ls1021a-qspi",
+ "fsl,ls1043a-qspi" followed by "fsl,ls1021a-qspi"
+ - reg : the first contains the register location and length,
+ the second contains the memory mapping address and length
+ - reg-names: Should contain the reg names "QuadSPI" and "QuadSPI-memory"
+ - interrupts : Should contain the interrupt for the device
+ - clocks : The clocks needed by the QuadSPI controller
+ - clock-names : Should contain the name of the clocks: "qspi_en" and "qspi".
+
+Optional properties:
+ - fsl,qspi-has-second-chip: The controller has two buses, bus A and bus B.
+ Each bus can be connected with two NOR flashes.
+ Most of the time, each bus only has one NOR flash
+ connected, this is the default case.
+ But if there are two NOR flashes connected to the
+ bus, you should enable this property.
+ (Please check the board's schematic.)
+ - big-endian : That means the IP register is big endian
+
+Example:
+
+qspi0: quadspi@40044000 {
+ compatible = "fsl,vf610-qspi";
+ reg = <0x40044000 0x1000>, <0x20000000 0x10000000>;
+ reg-names = "QuadSPI", "QuadSPI-memory";
+ interrupts = <0 24 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks VF610_CLK_QSPI0_EN>,
+ <&clks VF610_CLK_QSPI0>;
+ clock-names = "qspi_en", "qspi";
+
+ flash0: s25fl128s@0 {
+ ....
+ };
+};
+
+Example showing the usage of two SPI NOR devices:
+
+&qspi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_qspi2>;
+ status = "okay";
+
+ flash0: n25q256a@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "micron,n25q256a", "jedec,spi-nor";
+ spi-max-frequency = <29000000>;
+ reg = <0>;
+ };
+
+ flash1: n25q256a@1 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "micron,n25q256a", "jedec,spi-nor";
+ spi-max-frequency = <29000000>;
+ reg = <1>;
+ };
+};
--
2.7.4
