Add register regions for the second lane of dual-lane nodes.
This additional specification is needed so that the driver can stop
reaching beyond the tx and rx register allocations to get at the
second lane registers in a dual-lane PHY.
While in there, document #clock-cells as optional for PHYs that don't
provide a pipe clock. Also, document the pcs_misc register region, which
was being quietly supplied and used.
Signed-off-by: Evan Green <evgreen@xxxxxxxxxxxx>
Reviewed-by: Douglas Anderson <dianders@xxxxxxxxxxxx>
Reviewed-by: Rob Herring <robh@xxxxxxxxxx>
---
Changes in v5:
- Fix incorrect register value in example, copied from real life!
Changes in v4:
- Remove "status" from DT binding example (Rob)
Changes in v3: None
Changes in v2:
- Added dt bindings change, corresponding driver fixup, and USB PHY fixup
.../devicetree/bindings/phy/qcom-qmp-phy.txt | 70 +++++++++++++++++++---
1 file changed, 62 insertions(+), 8 deletions(-)
diff --git a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt
index fbc198d5dd39..f7b532125a4d 100644
--- a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt
+++ b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt
@@ -25,7 +25,7 @@ Required properties:
- For all others:
- The reg-names property shouldn't be defined.
- - #clock-cells: must be 1
+ - #clock-cells: must be 1 (PCIe and USB3 PHYs only)
- Phy pll outputs a bunch of clocks for Tx, Rx and Pipe
interface (for pipe based PHYs). These clock are then gate-controlled
by gcc.
@@ -82,23 +82,26 @@ Required nodes:
- Each device node of QMP phy is required to have as many child nodes as
the number of lanes the PHY has.
-Required properties for child node:
+Required properties for child nodes of PCIe PHYs (one child per lane):
- reg: list of offset and length pairs of register sets for PHY blocks -
- - index 0: tx
- - index 1: rx
- - index 2: pcs
- - index 3: pcs_misc (optional)
+ tx, rx, pcs, and pcs_misc (optional).
+ - #phy-cells: must be 0
+Required properties for a single "lanes" child node of non-PCIe PHYs:
+ - reg: list of offset and length pairs of register sets for PHY blocks
+ For 1-lane devices:
+ tx, rx, pcs, and (optionally) pcs_misc
+ For 2-lane devices:
+ tx0, rx0, pcs, tx1, rx1, and (optionally) pcs_misc
- #phy-cells: must be 0
-Required properties child node of pcie and usb3 qmp phys:
+Required properties for child node of PCIe and USB3 qmp phys:
- clocks: a list of phandles and clock-specifier pairs,
one for each entry in clock-names.
- clock-names: Must contain following:
"pipe<lane-number>" for pipe clock specific to each lane.
- clock-output-names: Name of the PHY clock that will be the parent for
the above pipe clock.
-
For "qcom,ipq8074-qmp-pcie-phy":
- "pcie20_phy0_pipe_clk" Pipe Clock parent
(or)
@@ -150,3 +153,54 @@ Example:
...
...
};
+
+ phy@88eb000 {
+ compatible = "qcom,sdm845-qmp-usb3-uni-phy";
+ reg = <0x88eb000 0x18c>;
+ #clock-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ clocks = <&gcc GCC_USB3_SEC_PHY_AUX_CLK>,
+ <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+ <&gcc GCC_USB3_SEC_CLKREF_CLK>,
+ <&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>;
+ clock-names = "aux", "cfg_ahb", "ref", "com_aux";
+
+ resets = <&gcc GCC_USB3PHY_PHY_SEC_BCR>,
+ <&gcc GCC_USB3_PHY_SEC_BCR>;
+ reset-names = "phy", "common";
+
+ lane@88eb200 {
+ reg = <0x88eb200 0x128>,
+ <0x88eb400 0x1fc>,
+ <0x88eb800 0x218>,
+ <0x88eb600 0x70>;
+ #phy-cells = <0>;
+ clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>;
+ clock-names = "pipe0";
+ clock-output-names = "usb3_uni_phy_pipe_clk_src";
+ };
+ };
+
+ phy@1d87000 {
+ compatible = "qcom,sdm845-qmp-ufs-phy";
+ reg = <0x1d87000 0x18c>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ clock-names = "ref",
+ "ref_aux";
+ clocks = <&gcc GCC_UFS_MEM_CLKREF_CLK>,
+ <&gcc GCC_UFS_PHY_PHY_AUX_CLK>;
+
+ lanes@1d87400 {
+ reg = <0x1d87400 0x108>,
+ <0x1d87600 0x1e0>,
+ <0x1d87c00 0x1dc>,
+ <0x1d87800 0x108>,
+ <0x1d87a00 0x1e0>;
+ #phy-cells = <0>;
+ };
+ };
--
2.16.4
