On 19 September 2018 at 16:31, Jim Quinlan <jim2101024@xxxxxxxxx> wrote:
> The DT bindings description of the Brcmstb PCIe device is described.
> This node can be used by almost all Broadcom settop box chips, using
> ARM, ARM64, or MIPS CPU architectures.
Oh, hey, *one* email made it finally through :P
>
> Signed-off-by: Jim Quinlan <jim2101024@xxxxxxxxx>
> Acked-by: Rob Herring <robh@xxxxxxxxxx>
> ---
> .../devicetree/bindings/pci/brcmstb-pcie.txt | 59 ++++++++++++++++++++++
> 1 file changed, 59 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pci/brcmstb-pcie.txt
>
> diff --git a/Documentation/devicetree/bindings/pci/brcmstb-pcie.txt b/Documentation/devicetree/bindings/pci/brcmstb-pcie.txt
> new file mode 100644
> index 0000000..a1a9ad5
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pci/brcmstb-pcie.txt
> @@ -0,0 +1,59 @@
> +Brcmstb PCIe Host Controller Device Tree Bindings
> +
> +Required Properties:
> +- compatible
> + "brcm,bcm7425-pcie" -- for 7425 family MIPS-based SOCs.
> + "brcm,bcm7435-pcie" -- for 7435 family MIPS-based SOCs.
> + "brcm,bcm7445-pcie" -- for 7445 and later ARM based SOCs (not including
> + the 7278).
> + "brcm,bcm7278-pcie" -- for 7278 family ARM-based SOCs.
> +
> +- reg -- the register start address and length for the PCIe reg block.
> +- interrupts -- two interrupts are specified; the first interrupt is for
> + the PCI host controller and the second is for MSI if the built-in
> + MSI controller is to be used.
> +- interrupt-names -- names of the interrupts (above): "pcie" and "msi".
> +- #address-cells -- set to <3>.
> +- #size-cells -- set to <2>.
> +- #interrupt-cells: set to <1>.
> +- interrupt-map-mask and interrupt-map, standard PCI properties to define the
> + mapping of the PCIe interface to interrupt numbers.
> +- ranges: ranges for the PCI memory and I/O regions.
> +- linux,pci-domain -- should be unique per host controller.
> +
> +Optional Properties:
> +- clocks -- phandle of pcie clock.
> +- clock-names -- set to "sw_pcie" if clocks is used.
> +- dma-ranges -- Specifies the inbound memory mapping regions when
> + an "identity map" is not possible.
> +- msi-controller -- this property is typically specified to have the
> + PCIe controller use its internal MSI controller.
> +- msi-parent -- set to use an external MSI interrupt controller.
> +- brcm,enable-ssc -- (boolean) indicates usage of spread-spectrum clocking.
> +- max-link-speed -- (integer) indicates desired generation of link:
> + 1 => 2.5 Gbps (gen1), 2 => 5.0 Gbps (gen2), 3 => 8.0 Gbps (gen3).
> +
> +Example Node:
> +
> +pcie0: pcie@f0460000 {
> + reg = <0x0 0xf0460000 0x0 0x9310>;
> + interrupts = <0x0 0x0 0x4>;
Your binding says two interrupts, your example has three - what's the
third interrupt for? Also you define the same for MSI and PCIe (I
assume) - is that expected? Are there systems where they are
different? I would expect the msi interrupt to be optional for the
case where its the same as the pcie one, and only required if it is
different.
Also your binding requires an interrupt-names propery, but it's
missing from the example.
> + compatible = "brcm,bcm7445-pcie";
> + #address-cells = <3>;
> + #size-cells = <2>;
> + ranges = <0x02000000 0x00000000 0x00000000 0x00000000 0xc0000000 0x00000000 0x08000000
> + 0x02000000 0x00000000 0x08000000 0x00000000 0xc8000000 0x00000000 0x08000000>;
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0 0 0 7>;
> + interrupt-map = <0 0 0 1 &intc 0 47 3
> + 0 0 0 2 &intc 0 48 3
> + 0 0 0 3 &intc 0 49 3
> + 0 0 0 4 &intc 0 50 3>;
> + clocks = <&sw_pcie0>;
> + clock-names = "sw_pcie";
> + msi-parent = <&pcie0>; /* use PCIe's internal MSI controller */
> + msi-controller; /* use PCIe's internal MSI controller */
> + brcm,ssc;
> + max-link-speed = <1>;
> + linux,pci-domain = <0>;
> + };
> --
> 1.9.0.138.g2de3478
>
Regards
Jonas
