Re: [PATCH] arm64: dts: Add support for NXP LS1028A SoC

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, Aug 29, 2018 at 08:44:28PM +0530, Sudhanshu Gupta wrote:
> From: Bhaskar Upadhaya <Bhaskar.Upadhaya@xxxxxxx>
> 
> LS1028A contains two ARM v8 CortexA72 processor cores
> with 32 KB L1-D cache and 48 KB L1-I cache
> 
> Features summary
>  Two 32-bit / 64-bit ARM v8 Cortex-A72 CPUs
>   - Arranged as single clusters of two cores sharing a 1 MB L2 cache
>   - Speed Up to 1.3 GHz
>   - Support for cluster power-gating.
>  Cache coherent interconnect (CCI-400)
>   - Hardware-managed data coherency
>   - Up to 400 MHz
>  32-bit DDR4 SDRAM memory controller with ECC
>  Two PCIe 3.0 controllers
>  One serial ATA (SATA 3.0) controller
>  Two high-speed USB 3.0 controllers with integrated PHY
> 
>  Following levels of DTSI/DTS files have been created for the LS1028A
>   SoC family:
> 
>          - fsl-ls1028a.dtsi:
>                  DTS-Include file for NXP LS1028A SoC.
> 
>          - fsl-ls1028a-qds.dts:
>                  DTS file for NXP LS1028A QDS board.
> 
>          - fsl-ls1028a-rdb.dts:
>                  DTS file for NXP LS1028A RDB board
> 
> Signed-off-by: Sudhanshu Gupta <sudhanshu.gupta@xxxxxxx>
> Signed-off-by: Rai Harninder <harninder.rai@xxxxxxx>
> Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@xxxxxxx>
> ---
>  arch/arm64/boot/dts/freescale/Makefile            |   2 +
>  arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts |  93 ++++++
>  arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts |  74 +++++
>  arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi    | 355 ++++++++++++++++++++++
>  4 files changed, 524 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
>  create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
>  create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
> 
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index d116144..b33c64a 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -3,6 +3,8 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-frwy.dtb
>  dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-frdm.dtb
>  dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-qds.dtb
>  dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-rdb.dtb
> +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds.dtb
> +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-rdb.dtb
>  dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-qds.dtb
>  dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-rdb.dtb
>  dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1046a-qds.dtb
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
> new file mode 100644
> index 0000000..586d5cd
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
> @@ -0,0 +1,93 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Device Tree file for NXP LS1028A QDS Board.
> + *
> + * Copyright 2018 NXP
> + *
> + * Harninder Rai <harninder.rai@xxxxxxx>
> + *
> + */
> +
> +/dts-v1/;
> +
> +#include "fsl-ls1028a.dtsi"
> +
> +/ {
> +	model = "LS1028A QDS Board";
> +	compatible = "fsl,ls1028a-qds", "fsl,ls1028a";
> +
> +	aliases {
> +		gpio0 = &gpio1;
> +		gpio1 = &gpio2;
> +		gpio2 = &gpio3;
> +		serial0 = &duart0;
> +		serial1 = &duart1;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +};
> +
> +&duart0 {
> +	status = "okay";
> +};
> +
> +&duart1 {
> +	status = "okay";
> +};
> +
> +&i2c0 {
> +	status = "okay";
> +
> +	pca9847@77 {

Please have generic node name for the device.

> +		compatible = "nxp,pca9847";
> +		reg = <0x77>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		i2c@2 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0x2>;
> +
> +			ina220@40 {

Ditto

> +				compatible = "ti,ina220";
> +				reg = <0x40>;
> +				shunt-resistor = <1000>;
> +			};
> +
> +			ina220@41 {
> +				compatible = "ti,ina220";
> +				reg = <0x41>;
> +				shunt-resistor = <1000>;
> +			};
> +		};
> +
> +		i2c@3 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0x3>;
> +
> +			eeprom@56 {
> +				compatible = "atmel,24c512";
> +				reg = <0x56>;
> +			};
> +
> +			eeprom@57 {
> +				compatible = "atmel,24c512";
> +				reg = <0x57>;
> +			};
> +
> +			sa56004@4c {

Ditto

> +				compatible = "nxp,sa56004";
> +				reg = <0x4c>;
> +			};
> +
> +			rtc@51 {
> +				compatible = "nxp,pcf2129";
> +				reg = <0x51>;
> +			};

Sort the nodes in order of unit-address.

> +		};
> +	};
> +};
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
> new file mode 100644
> index 0000000..e5c4309
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
> @@ -0,0 +1,74 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Device Tree file for NXP LS1028A RDB Board.
> + *
> + * Copyright 2018 NXP
> + *
> + * Harninder Rai <harninder.rai@xxxxxxx>
> + *
> + */
> +
> +/dts-v1/;
> +#include "fsl-ls1028a.dtsi"
> +
> +/ {
> +	model = "LS1028A RDB Board";
> +	compatible = "fsl,ls1028a-rdb", "fsl,ls1028a";
> +
> +	aliases {
> +		serial0 = &duart0;
> +		serial1 = &duart1;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +};
> +
> +&i2c0 {
> +	status = "okay";

Have a newline between property and child node.

> +	pca9847@77 {
> +		compatible = "nxp,pca9847";
> +		reg = <0x77>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		i2c@2 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0x02>;
> +
> +			ina220@40 {
> +				compatible = "ti,ina220";
> +				reg = <0x40>;
> +				shunt-resistor = <500>;
> +			};
> +		};
> +
> +		i2c@3 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0x3>;
> +
> +			sa56004@4c {
> +				compatible = "nxp,sa56004";
> +				reg = <0x4c>;
> +			};
> +
> +			rtc@51 {
> +				compatible = "nxp,pcf2129";
> +				reg = <0x51>;
> +			};
> +		};
> +	};
> +
> +
> +};
> +
> +&duart0 {
> +	status = "okay";
> +};
> +
> +&duart1 {
> +	status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
> new file mode 100644
> index 0000000..bc860e2
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
> @@ -0,0 +1,355 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Device Tree Include file for NXP Layerscape-1028A family SoC.
> + *
> + * Copyright 2018 NXP
> + *
> + * Harninder Rai <harninder.rai@xxxxxxx>
> + *
> + */
> +
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/thermal/thermal.h>
> +
> +/ {
> +	compatible = "fsl,ls1028a";
> +	interrupt-parent = <&gic>;
> +	#address-cells = <2>;
> +	#size-cells = <2>;
> +
> +	cpus {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		cpu0: cpu@0 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a72";
> +			reg = <0x0>;
> +			clocks = <&clockgen 1 0>;
> +			next-level-cache = <&l2>;
> +			cpu-idle-states = <&CPU_PH20>;
> +			#cooling-cells = <2>;
> +		};
> +
> +		cpu1: cpu@1 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a72";
> +			reg = <0x1>;
> +			clocks = <&clockgen 1 0>;
> +			next-level-cache = <&l2>;
> +			cpu-idle-states = <&CPU_PH20>;
> +		};
> +
> +		l2: l2-cache {
> +			compatible = "cache";
> +		};
> +	};
> +
> +	idle-states {
> +		/*
> +		 * PSCI node is not added default, U-boot will add missing
> +		 * parts if it determines to use PSCI.
> +		 */
> +		entry-method = "arm,psci";
> +
> +		CPU_PH20: cpu-ph20 {
> +			compatible = "arm,idle-state";
> +			idle-state-name = "PH20";
> +			arm,psci-suspend-param = <0x00010000>;
> +			entry-latency-us = <1000>;
> +			exit-latency-us = <1000>;
> +			min-residency-us = <3000>;
> +		};
> +	};
> +
> +	memory@80000000 {
> +		device_type = "memory";

With unit-address present on node name, a 'reg' property is required.

> +	};
> +
> +	sysclk: sysclk {

clock-sysclk for node name might be better?

> +		compatible = "fixed-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <100000000>;
> +		clock-output-names = "sysclk";
> +	};
> +
> +	reboot {
> +		compatible ="syscon-reboot";
> +		regmap = <&dcfg>;
> +		offset = <0xb0>;
> +		mask = <0x02>;
> +		status = "disabled";

For such reboot support, I do not see why it should be disabled by
default.

> +	};
> +
> +	timer {
> +		compatible = "arm,armv8-timer";
> +		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(0xf) |
> +					  IRQ_TYPE_LEVEL_LOW)>,
> +			     <GIC_PPI 14 (GIC_CPU_MASK_RAW(0xf) |
> +					  IRQ_TYPE_LEVEL_LOW)>,
> +			     <GIC_PPI 11 (GIC_CPU_MASK_RAW(0xf) |
> +					  IRQ_TYPE_LEVEL_LOW)>,
> +			     <GIC_PPI 10 (GIC_CPU_MASK_RAW(0xf) |
> +					  IRQ_TYPE_LEVEL_LOW)>;
> +	};
> +
> +	pmu {
> +		compatible = "arm,cortex-a72-pmu";
> +		interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
> +		interrupt-affinity = <&cpu0>,
> +				     <&cpu1>;
> +		status = "disabled";

Ditto

> +	};
> +
> +	gic: interrupt-controller@6000000 {
> +		compatible= "arm,gic-v3";
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		ranges;
> +		reg= <0x0 0x06000000 0 0x10000>, /* GIC Dist */
> +			<0x0 0x06040000 0 0x40000>; /* GIC Redistributor */
> +		#interrupt-cells= <3>;
> +		interrupt-controller;
> +		interrupts = <GIC_PPI 9 (GIC_CPU_MASK_RAW(0xf) |
> +					 IRQ_TYPE_LEVEL_LOW)>;
> +		its:gic-its@6020000 {

There should be a space between label and node name.

> +			compatible = "arm,gic-v3-its";
> +			msi-controller;
> +			reg = <0x0 0x06020000 0 0x20000>;/* GIC Translater */
> +		};
> +	};
> +
> +	soc: soc {
> +		compatible = "simple-bus";
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		ranges;
> +
> +		smmu: iommu@5000000 {
> +			compatible = "arm,mmu-500";
> +			reg = <0 0x5000000 0 0x800000>;
> +			#global-interrupts = <8>;
> +			#iommu-cells = <1>;
> +			stream-match-mask = <0x7C00>;
> +			/* global secure fault */
> +			interrupts = <0 13 4>,
> +			/* combined secure interrupt */
> +				     <0 14 4>,
> +			/* global non-secure fault */
> +				     <0 15 4>,
> +			/* combined non-secure interrupt */
> +				     <0 16 4>,
> +			/* performance counter interrupts 0-7 */
> +				     <0 211 4>, <0 212 4>,
> +				     <0 213 4>, <0 214 4>,
> +			/* per context interrupt, 64 interrupts */
> +				     <0 146 4>, <0 147 4>,
> +				     <0 148 4>, <0 149 4>,
> +				     <0 150 4>, <0 151 4>,
> +				     <0 152 4>, <0 153 4>,
> +				     <0 154 4>, <0 155 4>,
> +				     <0 156 4>, <0 157 4>,
> +				     <0 158 4>, <0 159 4>,
> +				     <0 160 4>, <0 161 4>,
> +				     <0 162 4>, <0 163 4>,
> +				     <0 164 4>, <0 165 4>,
> +				     <0 166 4>, <0 167 4>,
> +				     <0 168 4>, <0 169 4>,
> +				     <0 170 4>, <0 171 4>,
> +				     <0 172 4>, <0 173 4>,
> +				     <0 174 4>, <0 175 4>,
> +				     <0 176 4>, <0 177 4>,
> +				     <0 178 4>, <0 179 4>,
> +				     <0 180 4>, <0 181 4>,
> +				     <0 182 4>, <0 183 4>,
> +				     <0 184 4>, <0 185 4>,
> +				     <0 186 4>, <0 187 4>,
> +				     <0 188 4>, <0 189 4>,
> +				     <0 190 4>, <0 191 4>,
> +				     <0 192 4>, <0 193 4>,
> +				     <0 194 4>, <0 195 4>,
> +				     <0 196 4>, <0 197 4>,
> +				     <0 198 4>, <0 199 4>,
> +				     <0 200 4>, <0 201 4>,
> +				     <0 202 4>, <0 203 4>,
> +				     <0 204 4>, <0 205 4>,
> +				     <0 206 4>, <0 207 4>,
> +				     <0 208 4>, <0 209 4>;
> +		};
> +
> +		ddr: memory-controller@1080000 {
> +			compatible = "fsl,qoriq-memory-controller";
> +			reg = <0x0 0x1080000 0x0 0x1000>;
> +			interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
> +			big-endian;
> +		};
> +
> +		scfg: scfg@1fc0000 {

syscon is recommended by device tree spec as the node name.

> +			compatible = "fsl,ls1028a-scfg", "syscon";
> +			reg = <0x0 0x1fc0000 0x0 0x10000>;
> +			big-endian;
> +		};
> +
> +		dcfg: dcfg@1e00000 {

Ditto

> +			compatible = "fsl,ls1028a-dcfg", "syscon";
> +			reg = <0x0 0x1e00000 0x0 0x10000>;
> +			big-endian;
> +		};
> +
> +		clockgen: clocking@1300000 {

clock-controller is recommended by device tree spec as the node name.
> +			compatible = "fsl,ls1028a-clockgen";
> +			reg = <0x0 0x1300000 0x0 0xa0000>;
> +			#clock-cells = <2>;
> +			clocks = <&sysclk>;
> +		};

Nodes should be well sorted in unit-address.

> +
> +		i2c0: i2c@2000000 {
> +			compatible = "fsl,vf610-i2c";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0x0 0x2000000 0x0 0x10000>;
> +			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&clockgen 4 1>;
> +			dma-names = "tx", "rx";
> +			status = "disabled";
> +		};
> +
> +		i2c1: i2c@2010000 {
> +			compatible = "fsl,vf610-i2c";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0x0 0x2010000 0x0 0x10000>;
> +			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&clockgen 4 1>;
> +			status = "disabled";
> +		};
> +
> +		i2c2: i2c@2020000 {
> +			compatible = "fsl,vf610-i2c";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0x0 0x2020000 0x0 0x10000>;
> +			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&clockgen 4 1>;
> +			status = "disabled";
> +		};
> +
> +		i2c3: i2c@2030000 {
> +			compatible = "fsl,vf610-i2c";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0x0 0x2030000 0x0 0x10000>;
> +			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&clockgen 4 1>;
> +			status = "disabled";
> +		};
> +
> +		i2c4: i2c@2040000 {
> +			compatible = "fsl,vf610-i2c";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0x0 0x2040000 0x0 0x10000>;
> +			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&clockgen 4 1>;
> +			status = "disabled";
> +		};
> +
> +		i2c5: i2c@2050000 {
> +			compatible = "fsl,vf610-i2c";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0x0 0x2050000 0x0 0x10000>;
> +			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&clockgen 4 1>;
> +			status = "disabled";
> +		};
> +
> +		i2c6: i2c@2060000 {
> +			compatible = "fsl,vf610-i2c";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0x0 0x2060000 0x0 0x10000>;
> +			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&clockgen 4 1>;
> +			status = "disabled";
> +		};
> +
> +		i2c7: i2c@2070000 {
> +			compatible = "fsl,vf610-i2c";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0x0 0x2070000 0x0 0x10000>;
> +			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&clockgen 4 1>;
> +			status = "disabled";
> +		};
> +
> +		duart0: serial@21c0500 {
> +			compatible = "fsl,ns16550", "ns16550a";
> +			reg = <0x00 0x21c0500 0x0 0x100>;
> +			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&clockgen 4 1>;
> +		};
> +
> +		duart1: serial@21c0600 {
> +			compatible = "fsl,ns16550", "ns16550a";
> +			reg = <0x00 0x21c0600 0x0 0x100>;
> +			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&clockgen 4 1>;
> +		};
> +
> +		gpio1: gpio@2300000 {
> +			compatible = "fsl,qoriq-gpio";
> +			reg = <0x0 0x2300000 0x0 0x10000>;
> +			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +
> +		gpio2: gpio@2310000 {
> +			compatible = "fsl,qoriq-gpio";
> +			reg = <0x0 0x2310000 0x0 0x10000>;
> +			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +
> +		gpio3: gpio@2320000 {
> +			compatible = "fsl,qoriq-gpio";
> +			reg = <0x0 0x2320000 0x0 0x10000>;
> +			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +
> +		wdog0: watchdog@23c0000 {
> +			compatible= "arm,armv8-timer";

Why does a watchdog device get a timer compatible?

Shawn

> +			reg = <0x0 0x23c0000 0x0 0x10000>;
> +			interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&clockgen 4 1>;
> +			big-endian;
> +			status = "disabled";
> +		};
> +
> +		sata: sata@3200000 {
> +			compatible = "fsl,ls1028a-ahci";
> +			reg = <0x0 0x3200000 0x0 0x10000>,
> +				<0x0 0x20140520 0x0 0x4>;
> +			reg-names = "ahci", "sata-ecc";
> +			interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&clockgen 4 1>;
> +			status = "disabled";
> +		};
> +
> +	};
> +};
> +
> -- 
> 1.9.1
> 
> 
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux