[PATCH] arm64: dts: Add support for NXP LS1028A SoC

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



From: Bhaskar Upadhaya <Bhaskar.Upadhaya@xxxxxxx>

LS1028A contains two ARM v8 CortexA72 processor cores
with 32 KB L1-D cache and 48 KB L1-I cache

Features summary
 Two 32-bit / 64-bit ARM v8 Cortex-A72 CPUs
  - Arranged as single clusters of two cores sharing a 1 MB L2 cache
  - Speed Up to 1.3 GHz
  - Support for cluster power-gating.
 Cache coherent interconnect (CCI-400)
  - Hardware-managed data coherency
  - Up to 400 MHz
 32-bit DDR4 SDRAM memory controller with ECC
 Two PCIe 3.0 controllers
 One serial ATA (SATA 3.0) controller
 Two high-speed USB 3.0 controllers with integrated PHY

 Following levels of DTSI/DTS files have been created for the LS1028A
  SoC family:

         - fsl-ls1028a.dtsi:
                 DTS-Include file for NXP LS1028A SoC.

         - fsl-ls1028a-qds.dts:
                 DTS file for NXP LS1028A QDS board.

         - fsl-ls1028a-rdb.dts:
                 DTS file for NXP LS1028A RDB board

Signed-off-by: Sudhanshu Gupta <sudhanshu.gupta@xxxxxxx>
Signed-off-by: Rai Harninder <harninder.rai@xxxxxxx>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@xxxxxxx>
---
 arch/arm64/boot/dts/freescale/Makefile            |   2 +
 arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts |  93 ++++++
 arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts |  74 +++++
 arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi    | 355 ++++++++++++++++++++++
 4 files changed, 524 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
 create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
 create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index d116144..b33c64a 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -3,6 +3,8 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-frwy.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-frdm.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-qds.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-rdb.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-rdb.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-qds.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-rdb.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1046a-qds.dtb
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
new file mode 100644
index 0000000..586d5cd
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
@@ -0,0 +1,93 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for NXP LS1028A QDS Board.
+ *
+ * Copyright 2018 NXP
+ *
+ * Harninder Rai <harninder.rai@xxxxxxx>
+ *
+ */
+
+/dts-v1/;
+
+#include "fsl-ls1028a.dtsi"
+
+/ {
+	model = "LS1028A QDS Board";
+	compatible = "fsl,ls1028a-qds", "fsl,ls1028a";
+
+	aliases {
+		gpio0 = &gpio1;
+		gpio1 = &gpio2;
+		gpio2 = &gpio3;
+		serial0 = &duart0;
+		serial1 = &duart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&duart0 {
+	status = "okay";
+};
+
+&duart1 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	pca9847@77 {
+		compatible = "nxp,pca9847";
+		reg = <0x77>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x2>;
+
+			ina220@40 {
+				compatible = "ti,ina220";
+				reg = <0x40>;
+				shunt-resistor = <1000>;
+			};
+
+			ina220@41 {
+				compatible = "ti,ina220";
+				reg = <0x41>;
+				shunt-resistor = <1000>;
+			};
+		};
+
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x3>;
+
+			eeprom@56 {
+				compatible = "atmel,24c512";
+				reg = <0x56>;
+			};
+
+			eeprom@57 {
+				compatible = "atmel,24c512";
+				reg = <0x57>;
+			};
+
+			sa56004@4c {
+				compatible = "nxp,sa56004";
+				reg = <0x4c>;
+			};
+
+			rtc@51 {
+				compatible = "nxp,pcf2129";
+				reg = <0x51>;
+			};
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
new file mode 100644
index 0000000..e5c4309
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
@@ -0,0 +1,74 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for NXP LS1028A RDB Board.
+ *
+ * Copyright 2018 NXP
+ *
+ * Harninder Rai <harninder.rai@xxxxxxx>
+ *
+ */
+
+/dts-v1/;
+#include "fsl-ls1028a.dtsi"
+
+/ {
+	model = "LS1028A RDB Board";
+	compatible = "fsl,ls1028a-rdb", "fsl,ls1028a";
+
+	aliases {
+		serial0 = &duart0;
+		serial1 = &duart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&i2c0 {
+	status = "okay";
+	pca9847@77 {
+		compatible = "nxp,pca9847";
+		reg = <0x77>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x02>;
+
+			ina220@40 {
+				compatible = "ti,ina220";
+				reg = <0x40>;
+				shunt-resistor = <500>;
+			};
+		};
+
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x3>;
+
+			sa56004@4c {
+				compatible = "nxp,sa56004";
+				reg = <0x4c>;
+			};
+
+			rtc@51 {
+				compatible = "nxp,pcf2129";
+				reg = <0x51>;
+			};
+		};
+	};
+
+
+};
+
+&duart0 {
+	status = "okay";
+};
+
+&duart1 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
new file mode 100644
index 0000000..bc860e2
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
@@ -0,0 +1,355 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree Include file for NXP Layerscape-1028A family SoC.
+ *
+ * Copyright 2018 NXP
+ *
+ * Harninder Rai <harninder.rai@xxxxxxx>
+ *
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+	compatible = "fsl,ls1028a";
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			reg = <0x0>;
+			clocks = <&clockgen 1 0>;
+			next-level-cache = <&l2>;
+			cpu-idle-states = <&CPU_PH20>;
+			#cooling-cells = <2>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			reg = <0x1>;
+			clocks = <&clockgen 1 0>;
+			next-level-cache = <&l2>;
+			cpu-idle-states = <&CPU_PH20>;
+		};
+
+		l2: l2-cache {
+			compatible = "cache";
+		};
+	};
+
+	idle-states {
+		/*
+		 * PSCI node is not added default, U-boot will add missing
+		 * parts if it determines to use PSCI.
+		 */
+		entry-method = "arm,psci";
+
+		CPU_PH20: cpu-ph20 {
+			compatible = "arm,idle-state";
+			idle-state-name = "PH20";
+			arm,psci-suspend-param = <0x00010000>;
+			entry-latency-us = <1000>;
+			exit-latency-us = <1000>;
+			min-residency-us = <3000>;
+		};
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+	};
+
+	sysclk: sysclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <100000000>;
+		clock-output-names = "sysclk";
+	};
+
+	reboot {
+		compatible ="syscon-reboot";
+		regmap = <&dcfg>;
+		offset = <0xb0>;
+		mask = <0x02>;
+		status = "disabled";
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(0xf) |
+					  IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_RAW(0xf) |
+					  IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_RAW(0xf) |
+					  IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_RAW(0xf) |
+					  IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	pmu {
+		compatible = "arm,cortex-a72-pmu";
+		interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>,
+				     <&cpu1>;
+		status = "disabled";
+	};
+
+	gic: interrupt-controller@6000000 {
+		compatible= "arm,gic-v3";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+		reg= <0x0 0x06000000 0 0x10000>, /* GIC Dist */
+			<0x0 0x06040000 0 0x40000>; /* GIC Redistributor */
+		#interrupt-cells= <3>;
+		interrupt-controller;
+		interrupts = <GIC_PPI 9 (GIC_CPU_MASK_RAW(0xf) |
+					 IRQ_TYPE_LEVEL_LOW)>;
+		its:gic-its@6020000 {
+			compatible = "arm,gic-v3-its";
+			msi-controller;
+			reg = <0x0 0x06020000 0 0x20000>;/* GIC Translater */
+		};
+	};
+
+	soc: soc {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		smmu: iommu@5000000 {
+			compatible = "arm,mmu-500";
+			reg = <0 0x5000000 0 0x800000>;
+			#global-interrupts = <8>;
+			#iommu-cells = <1>;
+			stream-match-mask = <0x7C00>;
+			/* global secure fault */
+			interrupts = <0 13 4>,
+			/* combined secure interrupt */
+				     <0 14 4>,
+			/* global non-secure fault */
+				     <0 15 4>,
+			/* combined non-secure interrupt */
+				     <0 16 4>,
+			/* performance counter interrupts 0-7 */
+				     <0 211 4>, <0 212 4>,
+				     <0 213 4>, <0 214 4>,
+			/* per context interrupt, 64 interrupts */
+				     <0 146 4>, <0 147 4>,
+				     <0 148 4>, <0 149 4>,
+				     <0 150 4>, <0 151 4>,
+				     <0 152 4>, <0 153 4>,
+				     <0 154 4>, <0 155 4>,
+				     <0 156 4>, <0 157 4>,
+				     <0 158 4>, <0 159 4>,
+				     <0 160 4>, <0 161 4>,
+				     <0 162 4>, <0 163 4>,
+				     <0 164 4>, <0 165 4>,
+				     <0 166 4>, <0 167 4>,
+				     <0 168 4>, <0 169 4>,
+				     <0 170 4>, <0 171 4>,
+				     <0 172 4>, <0 173 4>,
+				     <0 174 4>, <0 175 4>,
+				     <0 176 4>, <0 177 4>,
+				     <0 178 4>, <0 179 4>,
+				     <0 180 4>, <0 181 4>,
+				     <0 182 4>, <0 183 4>,
+				     <0 184 4>, <0 185 4>,
+				     <0 186 4>, <0 187 4>,
+				     <0 188 4>, <0 189 4>,
+				     <0 190 4>, <0 191 4>,
+				     <0 192 4>, <0 193 4>,
+				     <0 194 4>, <0 195 4>,
+				     <0 196 4>, <0 197 4>,
+				     <0 198 4>, <0 199 4>,
+				     <0 200 4>, <0 201 4>,
+				     <0 202 4>, <0 203 4>,
+				     <0 204 4>, <0 205 4>,
+				     <0 206 4>, <0 207 4>,
+				     <0 208 4>, <0 209 4>;
+		};
+
+		ddr: memory-controller@1080000 {
+			compatible = "fsl,qoriq-memory-controller";
+			reg = <0x0 0x1080000 0x0 0x1000>;
+			interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
+			big-endian;
+		};
+
+		scfg: scfg@1fc0000 {
+			compatible = "fsl,ls1028a-scfg", "syscon";
+			reg = <0x0 0x1fc0000 0x0 0x10000>;
+			big-endian;
+		};
+
+		dcfg: dcfg@1e00000 {
+			compatible = "fsl,ls1028a-dcfg", "syscon";
+			reg = <0x0 0x1e00000 0x0 0x10000>;
+			big-endian;
+		};
+
+		clockgen: clocking@1300000 {
+			compatible = "fsl,ls1028a-clockgen";
+			reg = <0x0 0x1300000 0x0 0xa0000>;
+			#clock-cells = <2>;
+			clocks = <&sysclk>;
+		};
+
+		i2c0: i2c@2000000 {
+			compatible = "fsl,vf610-i2c";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0x2000000 0x0 0x10000>;
+			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 1>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		i2c1: i2c@2010000 {
+			compatible = "fsl,vf610-i2c";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0x2010000 0x0 0x10000>;
+			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 1>;
+			status = "disabled";
+		};
+
+		i2c2: i2c@2020000 {
+			compatible = "fsl,vf610-i2c";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0x2020000 0x0 0x10000>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 1>;
+			status = "disabled";
+		};
+
+		i2c3: i2c@2030000 {
+			compatible = "fsl,vf610-i2c";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0x2030000 0x0 0x10000>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 1>;
+			status = "disabled";
+		};
+
+		i2c4: i2c@2040000 {
+			compatible = "fsl,vf610-i2c";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0x2040000 0x0 0x10000>;
+			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 1>;
+			status = "disabled";
+		};
+
+		i2c5: i2c@2050000 {
+			compatible = "fsl,vf610-i2c";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0x2050000 0x0 0x10000>;
+			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 1>;
+			status = "disabled";
+		};
+
+		i2c6: i2c@2060000 {
+			compatible = "fsl,vf610-i2c";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0x2060000 0x0 0x10000>;
+			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 1>;
+			status = "disabled";
+		};
+
+		i2c7: i2c@2070000 {
+			compatible = "fsl,vf610-i2c";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0x2070000 0x0 0x10000>;
+			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 1>;
+			status = "disabled";
+		};
+
+		duart0: serial@21c0500 {
+			compatible = "fsl,ns16550", "ns16550a";
+			reg = <0x00 0x21c0500 0x0 0x100>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 1>;
+		};
+
+		duart1: serial@21c0600 {
+			compatible = "fsl,ns16550", "ns16550a";
+			reg = <0x00 0x21c0600 0x0 0x100>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 1>;
+		};
+
+		gpio1: gpio@2300000 {
+			compatible = "fsl,qoriq-gpio";
+			reg = <0x0 0x2300000 0x0 0x10000>;
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio2: gpio@2310000 {
+			compatible = "fsl,qoriq-gpio";
+			reg = <0x0 0x2310000 0x0 0x10000>;
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio3: gpio@2320000 {
+			compatible = "fsl,qoriq-gpio";
+			reg = <0x0 0x2320000 0x0 0x10000>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		wdog0: watchdog@23c0000 {
+			compatible= "arm,armv8-timer";
+			reg = <0x0 0x23c0000 0x0 0x10000>;
+			interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 1>;
+			big-endian;
+			status = "disabled";
+		};
+
+		sata: sata@3200000 {
+			compatible = "fsl,ls1028a-ahci";
+			reg = <0x0 0x3200000 0x0 0x10000>,
+				<0x0 0x20140520 0x0 0x4>;
+			reg-names = "ahci", "sata-ecc";
+			interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 1>;
+			status = "disabled";
+		};
+
+	};
+};
+
-- 
1.9.1




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux