Re: [PATCH v4 09/13] ARM: dts: sun8i: r40: add sata node

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



在 2018-08-31五的 19:31 +0800,Chen-Yu Tsai写道:
> On Fri, Aug 31, 2018 at 6:54 PM Corentin Labbe
> <clabbe.montjoie@xxxxxxxxx> wrote:
> > 
> > On Fri, Aug 31, 2018 at 12:20:21PM +0200, maxime.ripard@xxxxxxxxxxx
> >  wrote:
> > > On Fri, Aug 31, 2018 at 09:56:31AM +0200, Corentin Labbe wrote:
> > > > On Fri, Aug 31, 2018 at 09:35:00AM +0200, Maxime Ripard wrote:
> > > > > On Thu, Aug 30, 2018 at 09:01:16PM +0200, Corentin Labbe
> > > > > wrote:
> > > > > > R40 have a sata controller which is the same as A20.
> > > > > > This patch adds a DT node for it.
> > > > > > 
> > > > > > Signed-off-by: Icenowy Zheng <icenowy@xxxxxxx>
> > > > > > Signed-off-by: Corentin Labbe <clabbe.montjoie@xxxxxxxxx>
> > > > > > ---
> > > > > >  arch/arm/boot/dts/sun8i-r40.dtsi | 23
> > > > > > +++++++++++++++++++++++
> > > > > >  1 file changed, 23 insertions(+)
> > > > > > 
> > > > > > diff --git a/arch/arm/boot/dts/sun8i-r40.dtsi
> > > > > > b/arch/arm/boot/dts/sun8i-r40.dtsi
> > > > > > index 852c2ccc3268..d6b5820da850 100644
> > > > > > --- a/arch/arm/boot/dts/sun8i-r40.dtsi
> > > > > > +++ b/arch/arm/boot/dts/sun8i-r40.dtsi
> > > > > > @@ -550,6 +550,29 @@
> > > > > >                         #size-cells = <0>;
> > > > > >                 };
> > > > > > 
> > > > > > +               ahci: sata@1c18000 {
> > > > > > +                       compatible = "allwinner,sun8i-r40-
> > > > > > ahci";
> > > > > > +                       reg = <0x01c18000 0x1000>;
> > > > > > +                       interrupts = <GIC_SPI 56
> > > > > > IRQ_TYPE_LEVEL_HIGH>;
> > > > > > +                       clocks = <&ccu CLK_BUS_SATA>, <&ccu
> > > > > > CLK_SATA>;
> > > > > > +                       resets = <&ccu RST_BUS_SATA>;
> > > > > > +                       resets-name = "ahci";
> > > > > > +                       #address-cells = <1>;
> > > > > > +                       #size-cells = <0>;
> > > > > > +                       status = "disabled";
> > > > > > +
> > > > > > +                       sata_port: sata-port@0 {
> > > > > > +                               reg = <0>;
> > > > > > +                               phys = <&sata_phy>;
> > > > > > +                       };
> > > > > > +               };
> > > > > > +
> > > > > > +               sata_phy: sata-phy@1c180c0  {
> > > > > > +                       compatible = "allwinner,sun8i-r40-
> > > > > > sata-phy";
> > > > > > +                       reg = <0x1c180c0 0x200>;
> > > > > 
> > > > > Overlapping devices in the DTS is not ok.
> > > > > 
> > > > 
> > > > I do the same than arch/arm/boot/dts/berlin2.dtsi (sata@e90000
> > > > phy@e900a0)
> > > > 
> > > > But since it is not a good justification, it seems that regmap
> > > > is my
> > > > only solution ?
> > > 
> > > I'm not even sure why you are moving the phy out of its original
> > > node
> > > (and driver).
> > > 
> > 
> > For using the phy-supply already handled by the code.
> > The other choice is to add another xxx-supply to ahci_platform.
> > Or to use hackily port_regulator for this regulator.
> 
> The PHY registers are in the AHCI's "vendor specific registers"
> region. Following that are the per-port registers, which the ahci
> driver will need access to. This doesn't look like it should
> deserve a separate device node.
> 
> What's wrong with handling the regulator directly in the ahci-sunxi
> PHY init code?

I remember I sent a patch that did this some times ago, and gets
rejected.

> 
> ChenYu




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux