On 06-08-18, 11:03, Bjorn Andersson wrote:
> On Mon 06 Aug 04:04 PDT 2018, Vinod Koul wrote:
>
> > From: Todor Tomov <todor.tomov@xxxxxxxxxx>
> >
> > Add DT binding document for Qualcomm Camera Control Interface (CCI)
> > I2C controller.
> >
> > Signed-off-by: Todor Tomov <todor.tomov@xxxxxxxxxx>
> > Signed-off-by: Vinod Koul <vkoul@xxxxxxxxxx>
> > ---
> > .../devicetree/bindings/i2c/i2c-qcom-cci.txt | 55 ++++++++++++++++++++++
> > 1 file changed, 55 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/i2c/i2c-qcom-cci.txt
> >
> > diff --git a/Documentation/devicetree/bindings/i2c/i2c-qcom-cci.txt b/Documentation/devicetree/bindings/i2c/i2c-qcom-cci.txt
> > new file mode 100644
> > index 000000000000..977978dd4444
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/i2c/i2c-qcom-cci.txt
> > @@ -0,0 +1,55 @@
> > +Qualcomm Camera Control Interface (CCI) I2C controller
> > +
> > +Required properties:
> > + - compatible: Should be one of:
> > + - "qcom,cci-v1.0.8" for 8916;
> > + - "qcom,cci-v1.4.0" for 8996.
>
> As pointed out by Rob previously we should either use version numbers or
> platform numbers, not both.
>
> So this should either be:
>
> - "qcom,cci-v1.0.8"
> - "qcom,cci-v1.4.0"
ok will use this one..
>
> or:
>
> - "qcom,msm8916-cci"
> - "qcom,msm8996-cci"
>
> > + - #address-cells: Should be <1>.
> > + - #size-cells: Should be <0>.
> > + - reg: Base address of the I2C controller and length of memory mapped region.
> > + - interrupts: Specifier for CCI I2C interrupt.
> > + - clocks: List of clock specifiers, one for each entry in clock-names.
> > + - clock-names: Should contain:
> > + - "mmss_mmagic_ahb" - on qcom,cci-v1.4.0 only;
> > + - "camss_top_ahb";
> > + - "cci_ahb";
> > + - "cci";
> > + - "camss_ahb".
> > +
> > +Required subnodes:
> > + - i2c-bus instances:
> > + Mandatory i2c-bus0 subnode
> > + Mandatory i2c-bus1 for qcom,cci-v1.4.0
>
> Rather than a bullet list, the subnodes are probably better described in
> text. I think most versions have two masters, so in order to not have to
> update this every time we add a new compatible we could probably write
> this in a more generic fashion.
>
> E.g.
>
> Required subnodes:
>
> The CCI provides I2C masters for one or two i2c busses, described as
> subdevices named "i2c-bus0" and "i2c-bus1".
okay but the v1-0-8 doesn't (8916) seem to have two busses, later ones yes.
>
> > + - Optional properties:
>
> "Optional properties for subnodes"
>
> > + - clock-frequency: Desired I2C bus clock frequency
> > + in Hz, defaults to 100 kHz if omitted.
> > +
> > +Required properties on qcom,cci-v1.4.0:
> > + - power-domains: Power domain specifier.
>
> Properties has to come before any subnodes in the dts, so move this
> above the subnode definition as well.
yes will do
>
> > +
> > +Example:
> > +
> > + cci@a0c000 {
> > + compatible = "qcom,cci-v1.4.0";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <0xa0c000 0x1000>;
> > + interrupts = <GIC_SPI 295 IRQ_TYPE_EDGE_RISING>;
> > + power-domains = <&mmcc CAMSS_GDSC>;
> > + clocks = <&mmcc MMSS_MMAGIC_AHB_CLK>,
> > + <&mmcc CAMSS_TOP_AHB_CLK>,
> > + <&mmcc CAMSS_CCI_AHB_CLK>,
> > + <&mmcc CAMSS_CCI_CLK>,
> > + <&mmcc CAMSS_AHB_CLK>;
> > + clock-names = "mmss_mmagic_ahb",
> > + "camss_top_ahb",
> > + "cci_ahb",
> > + "cci",
> > + "camss_ahb";
>
> Seems lines above this is indented with space and the following with
> tabs.
will fix
Thanks for the review.
--
~Vinod
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
