This patch set aims at bringing a device tree support for the sam9261.
It's mostly based on the sam9263 and sam9x5 stuff.
Changes since V4:
* change the compatibilty string for the bus matrix to
'atmel,at91sam9260-bus-matrix'
* add a documentation for the bus matrix DT binding
* panic if the DT description of the bus matrix is not found
* Fixed the GPIO banks' address range
Changes since V3:
* Added support for the touchscreen
* Added support for the spi dataflash
* Activated the TCB by default
* Reworked the patch organization to reduce the number of patchs
* changed the default bootargs (no mem description, UBI on mtdpart 5)
* Changed the xlate implementation of the at91 pinctrl driver to lock the GPIOs
for IRQs instead of requesting them (needed for the touchscreen driver)
* some stylistic changes
Changes since V2:
* removed the smc driver from the serie. It'll be posted in an independent
serie later.
* removed the DM9000 support (it'll come with the smc driver)
* the sam9261 now supports the Common Clock Framework (CCF). Note: to enable
the CCF you must remove from the kernel config the platforms that don't
support it.
* Added basic DT binding for the bus matrix
* Added support for USB host
* Added support for USB gadget
* in dts(i), replaced interrupt-parent with interrupts-extended
* changed the nand partition plan (same as for the sama5d3)
* removed 'mem' parameter in command line
* re-ordered dt-nodes in ascending address order.
* split the lcd support patch in 2 parts (SOC and board)
Change since V1:
* changed the DT representation to use address translation and separate the
timings' configuration from the device properties by adding a "simple-bus"
inetrmediate node.
* moved the smc driver from drivers/bus to drivers/memmory
* smc driver now accepts timings in nanoseconds as well as raw register values
* smc driver can clip the timings if they're out of bound and dump them to the
console
* DM9000 timings are now described in nanosecs (for the virtue of example)
supported features are:
* working with the Common Clock Framework and the old at91 clock implementation
* dbgu
* lcdc
* usb host
* usb gadget,
* spi dataflash
* nand flash
* touchscreen
* leds
* user buttons
In the TODO list:
* dm9000 (ethernet)
* audio
* mmc
This serie relies on the following patchs:
usb: at91-udc: fix irq and iomem resource retrieval
ARM: at91: prepare sam9 dt boards transition to common
Jean-Jacques
Jean-Jacques Hiblot (9):
at91: dt: Adds support for the bus matrix declaration in the DT
dt: bindings: at91: Add a new binding for the bus matrix
at91: pinctrl: don't request GPIOs used for interrupts but lock them
as IRQ
at91: dt: Add at91sam9261 dt SoC support
at91: dt: defconfig: Added the sam9261 to the list of DT-enabled SOCs
at91: dt: sam9261: Device Tree support for the at91sam9261ek
at91: updated the at91_dt_defconfig with support for the ADS7846
ARM: at91: prepare common clk transition for sam9261 SoC
ARM: at91: move sam9261 SoC to common clk
.../devicetree/bindings/arm/atmel-at91.txt | 14 +
arch/arm/boot/dts/Makefile | 2 +
arch/arm/boot/dts/at91sam9261.dtsi | 740 +++++++++++++++++++++
arch/arm/boot/dts/at91sam9261ek.dts | 204 ++++++
arch/arm/configs/at91_dt_defconfig | 2 +
arch/arm/mach-at91/Kconfig | 1 -
arch/arm/mach-at91/at91sam9261.c | 25 +-
arch/arm/mach-at91/setup.c | 21 +
drivers/pinctrl/pinctrl-at91.c | 5 +-
9 files changed, 1008 insertions(+), 6 deletions(-)
create mode 100644 arch/arm/boot/dts/at91sam9261.dtsi
create mode 100644 arch/arm/boot/dts/at91sam9261ek.dts
--
1.9.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
