On Thu, 28 Jun 2018 11:30:37 -0700
Siddartha Mohanadoss <smohanad@xxxxxxxxxxxxxx> wrote:
> This patch adds support for QCOM SPMI PMIC5 family
> of ADC driver that supports hardware based offset and
> gain compensation. The ADC peripheral can measure both
> voltage and current channels whose input signal is
> connected to the PMIC ADC AMUX.
>
> The register set and configuration has been refreshed
> compared to the prior QCOM PMIC ADC family. Register
> ADC5 as part of the IIO framework.
>
> Signed-off-by: Siddartha Mohanadoss <smohanad@xxxxxxxxxxxxxx>
I guess I missed the oddity that is power channel handling on v1.
Why are you using IIO_VAL_INT_MULTIPLE? That was added
to support the weirdness of quaternion outputs so I'm not
sure what the intent is here.
(and I did a slightly panic ridden grep to see if this was a cut
and paste bug - thankfully not - it seems to be unique to this driver :)
Otherwise a few minors.
Jonathan
> ---
> drivers/iio/adc/Kconfig | 20 +
> drivers/iio/adc/Makefile | 1 +
> drivers/iio/adc/qcom-spmi-adc5.c | 878 +++++++++++++++++++++++++++++++++++++
> drivers/iio/adc/qcom-vadc-common.c | 230 +++++++++-
> drivers/iio/adc/qcom-vadc-common.h | 56 +++
> 5 files changed, 1180 insertions(+), 5 deletions(-)
> create mode 100644 drivers/iio/adc/qcom-spmi-adc5.c
>
> diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
> index 9da7907..93ac929 100644
> --- a/drivers/iio/adc/Kconfig
> +++ b/drivers/iio/adc/Kconfig
> @@ -597,6 +597,26 @@ config QCOM_SPMI_VADC
> To compile this driver as a module, choose M here: the module will
> be called qcom-spmi-vadc.
>
> +config QCOM_SPMI_ADC5
> + tristate "Qualcomm Technologies Inc. SPMI PMIC5 ADC"
> + depends on SPMI
> + select REGMAP_SPMI
> + select QCOM_VADC_COMMON
> + help
> + This is the IIO Voltage PMIC5 ADC driver for Qualcomm Technologies Inc.
> +
> + The driver supports multiple channels read. The ADC is a 16-bit
> + sigma-delta ADC. The hardware supports calibrated results for
> + conversion requests and clients include reading voltage phone
> + power, on board system thermistors connected to the PMIC ADC,
> + PMIC die temperature, charger temperature, battery current, USB voltage
> + input, voltage signals connected to supported PMIC GPIO inputs. The
> + hardware supports internal pull-up for thermistors and can choose between
> + a 100k, 30k and 400k pull up using the ADC channels.
> +
> + To compile this driver as a module, choose M here: the module will
> + be called qcom-spmi-adc5.
> +
> config RCAR_GYRO_ADC
> tristate "Renesas R-Car GyroADC driver"
> depends on ARCH_RCAR_GEN2 || COMPILE_TEST
> diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
> index 28a9423..9533a82 100644
> --- a/drivers/iio/adc/Makefile
> +++ b/drivers/iio/adc/Makefile
> @@ -56,6 +56,7 @@ obj-$(CONFIG_PALMAS_GPADC) += palmas_gpadc.o
> obj-$(CONFIG_QCOM_SPMI_IADC) += qcom-spmi-iadc.o
> obj-$(CONFIG_QCOM_VADC_COMMON) += qcom-vadc-common.o
> obj-$(CONFIG_QCOM_SPMI_VADC) += qcom-spmi-vadc.o
> +obj-$(CONFIG_QCOM_SPMI_ADC5) += qcom-spmi-adc5.o
> obj-$(CONFIG_QCOM_PM8XXX_XOADC) += qcom-pm8xxx-xoadc.o
> obj-$(CONFIG_RCAR_GYRO_ADC) += rcar-gyroadc.o
> obj-$(CONFIG_ROCKCHIP_SARADC) += rockchip_saradc.o
> diff --git a/drivers/iio/adc/qcom-spmi-adc5.c b/drivers/iio/adc/qcom-spmi-adc5.c
> new file mode 100644
> index 0000000..75308df
> --- /dev/null
> +++ b/drivers/iio/adc/qcom-spmi-adc5.c
> @@ -0,0 +1,878 @@
> +/*
> + * Copyright (c) 2018, The Linux Foundation. All rights reserved.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 and
> + * only version 2 as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
SPDX a possibility?
> + */
> +
> +#include <linux/bitops.h>
> +#include <linux/completion.h>
> +#include <linux/delay.h>
> +#include <linux/err.h>
> +#include <linux/iio/iio.h>
> +#include <linux/interrupt.h>
> +#include <linux/kernel.h>
> +#include <linux/math64.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +#include <linux/slab.h>
> +#include <linux/log2.h>
> +
> +#include <dt-bindings/iio/qcom,spmi-vadc.h>
> +#include "qcom-vadc-common.h"
> +
> +#define ADC5_USR_REVISION1 0x0
> +#define ADC5_USR_STATUS1 0x8
> +#define ADC5_USR_STATUS1_REQ_STS BIT(1)
> +#define ADC5_USR_STATUS1_EOC BIT(0)
> +#define ADC5_USR_STATUS1_REQ_STS_EOC_MASK 0x3
> +
> +#define ADC5_USR_STATUS2 0x9
> +#define ADC5_USR_STATUS2_CONV_SEQ_MASK 0x70
> +#define ADC5_USR_STATUS2_CONV_SEQ_MASK_SHIFT 0x5
> +
> +#define ADC5_USR_IBAT_MEAS 0xf
> +#define ADC5_USR_IBAT_MEAS_SUPPORTED BIT(0)
> +
> +#define ADC5_USR_DIG_PARAM 0x42
> +#define ADC5_USR_DIG_PARAM_CAL_VAL BIT(6)
> +#define ADC5_USR_DIG_PARAM_CAL_VAL_SHIFT 6
> +#define ADC5_USR_DIG_PARAM_CAL_SEL 0x30
> +#define ADC5_USR_DIG_PARAM_CAL_SEL_SHIFT 4
> +#define ADC5_USR_DIG_PARAM_DEC_RATIO_SEL 0xc
> +#define ADC5_USR_DIG_PARAM_DEC_RATIO_SEL_SHIFT 2
> +
> +#define ADC5_USR_FAST_AVG_CTL 0x43
> +#define ADC5_USR_FAST_AVG_CTL_EN BIT(7)
> +#define ADC5_USR_FAST_AVG_CTL_SAMPLES_MASK 0x7
> +
> +#define ADC5_USR_CH_SEL_CTL 0x44
> +
> +#define ADC5_USR_DELAY_CTL 0x45
> +#define ADC5_USR_HW_SETTLE_DELAY_MASK 0xf
> +
> +#define ADC5_USR_EN_CTL1 0x46
> +#define ADC5_USR_EN_CTL1_ADC_EN BIT(7)
> +
> +#define ADC5_USR_CONV_REQ 0x47
> +#define ADC5_USR_CONV_REQ_REQ BIT(7)
> +
> +#define ADC5_USR_DATA0 0x50
> +
> +#define ADC5_USR_DATA1 0x51
> +
> +#define ADC5_USR_IBAT_DATA0 0x52
> +
> +#define ADC5_USR_IBAT_DATA1 0x53
> +
> +/*
> + * Conversion time varies based on the decimation, clock rate, fast average
> + * samples and measurements queued across different VADC peripherals.
> + * Set the timeout to a max of 100ms.
> + */
> +#define ADC5_CONV_TIME_MIN_US 263
> +#define ADC5_CONV_TIME_MAX_US 264
> +#define ADC5_CONV_TIME_RETRY 400
> +#define ADC5_CONV_TIMEOUT msecs_to_jiffies(100)
> +
> +/* Digital version >= 5.3 supports hw_settle_2 */
> +#define ADC5_HW_SETTLE_DIFF_MINOR 3
> +#define ADC5_HW_SETTLE_DIFF_MAJOR 5
> +
> +enum adc5_cal_method {
> + ADC5_NO_CAL = 0,
> + ADC5_RATIOMETRIC_CAL,
> + ADC5_ABSOLUTE_CAL
> +};
> +
> +enum adc5_cal_val {
> + ADC5_TIMER_CAL = 0,
> + ADC5_NEW_CAL
> +};
> +
> +/**
> + * struct adc5_channel_prop - ADC channel property.
> + * @channel: channel number, refer to the channel list.
> + * @cal_method: calibration method.
> + * @cal_val: calibration value
> + * @decimation: sampling rate supported for the channel.
> + * @prescale: channel scaling performed on the input signal.
> + * @hw_settle_time: the time between AMUX being configured and the
> + * start of conversion.
> + * @avg_samples: ability to provide single result from the ADC
> + * that is an average of multiple measurements.
> + * @scale_fn_type: Represents the scaling function to convert voltage
> + * physical units desired by the client for the channel.
> + * @datasheet_name: Channel name used in device tree.
> + */
> +struct adc5_channel_prop {
> + unsigned int channel;
> + enum adc5_cal_method cal_method;
> + enum adc5_cal_val cal_val;
> + unsigned int decimation;
> + unsigned int prescale;
> + unsigned int hw_settle_time;
> + unsigned int avg_samples;
> + enum vadc_scale_fn_type scale_fn_type;
> + const char *datasheet_name;
> +};
> +
> +/**
> + * struct adc5_chip - ADC private structure.
> + * @regmap: SPMI ADC5 peripheral register map field.
> + * @dev: SPMI ADC5 device.
> + * @base: base address for the ADC peripheral.
> + * @nchannels: number of ADC channels.
> + * @chan_props: array of ADC channel properties.
> + * @iio_chans: array of IIO channels specification.
> + * @poll_eoc: use polling instead of interrupt.
> + * @complete: ADC result notification after interrupt is received.
> + * @lock: ADC lock for access to the peripheral.
> + * @data: software configuration data.
> + */
> +struct adc5_chip {
> + struct regmap *regmap;
> + struct device *dev;
> + u16 base;
> + unsigned int nchannels;
> + struct adc5_channel_prop *chan_props;
> + struct iio_chan_spec *iio_chans;
> + bool poll_eoc;
> + struct completion complete;
> + struct mutex lock;
> + const struct adc_data *data;
> +};
> +
> +static const struct vadc_prescale_ratio adc5_prescale_ratios[] = {
> + {.num = 1, .den = 1},
> + {.num = 1, .den = 3},
> + {.num = 1, .den = 4},
> + {.num = 1, .den = 6},
> + {.num = 1, .den = 20},
> + {.num = 1, .den = 8},
> + {.num = 10, .den = 81},
> + {.num = 1, .den = 10},
> + {.num = 1, .den = 16}
> +};
> +
> +static int adc5_read(struct adc5_chip *adc, u16 offset, u8 *data, int len)
> +{
> + return regmap_bulk_read(adc->regmap, adc->base + offset, data, len);
> +}
> +
> +static int adc5_write(struct adc5_chip *adc, u16 offset, u8 *data, int len)
> +{
> + return regmap_bulk_write(adc->regmap, adc->base + offset, data, len);
> +}
> +
> +static int adc5_prescaling_from_dt(u32 num, u32 den)
> +{
> + unsigned int pre;
> +
> + for (pre = 0; pre < ARRAY_SIZE(adc5_prescale_ratios); pre++)
> + if (adc5_prescale_ratios[pre].num == num &&
> + adc5_prescale_ratios[pre].den == den)
> + break;
> +
> + if (pre == ARRAY_SIZE(adc5_prescale_ratios))
> + return -EINVAL;
> +
> + return pre;
> +}
> +
> +static int adc5_get_dig_version(struct adc5_chip *adc,
> + u8 *dig_version)
> +{
> + int ret;
> +
> + ret = adc5_read(adc, ADC5_USR_REVISION1, dig_version, 2);
return adc5_read(...)
> + if (ret)
> + return ret;
> +
> + return 0;
> +}
> +
> +static int adc5_hw_settle_time_from_dt(u32 value,
> + const unsigned int *hw_settle)
> +{
> + uint32_t i;
> +
> + for (i = 0; i < VADC_HW_SETTLE_SAMPLES_MAX; i++) {
> + if (value == hw_settle[i])
> + return i;
> + }
> +
> + return -EINVAL;
> +}
> +
> +static int adc5_avg_samples_from_dt(u32 value)
> +{
> + if (!is_power_of_2(value) || value > ADC5_AVG_SAMPLES_MAX)
> + return -EINVAL;
> +
> + return __ffs64(value);
> +}
> +
> +static int adc5_decimation_from_dt(u32 value,
> + const unsigned int *decimation)
> +{
> + uint32_t i;
> +
> + for (i = 0; i < ADC5_DECIMATION_SAMPLES_MAX; i++) {
> + if (value == decimation[i])
> + return i;
> + }
> +
> + return -EINVAL;
> +}
> +
> +static int adc5_read_current_data(struct adc5_chip *adc, u16 *data)
> +{
> + int ret;
> + u8 rslt_lsb = 0, rslt_msb = 0;
> +
> + ret = adc5_read(adc, ADC5_USR_IBAT_DATA0, &rslt_lsb, 1);
> + if (ret)
> + return ret;
> +
> + ret = adc5_read(adc, ADC5_USR_IBAT_DATA1, &rslt_msb, 1);
> + if (ret)
> + return ret;
> +
> + *data = (rslt_msb << 8) | rslt_lsb;
> +
> + if (*data == ADC5_USR_DATA_CHECK) {
> + pr_err("Invalid data:0x%x\n", *data);
> + return -EINVAL;
> + }
> +
> + return ret;
> +}
> +
> +static int adc5_read_voltage_data(struct adc5_chip *adc, u16 *data)
> +{
> + int ret;
> + u8 rslt_lsb, rslt_msb;
> +
> + ret = adc5_read(adc, ADC5_USR_DATA0, &rslt_lsb, 1);
> + if (ret)
> + return ret;
> +
> + ret = adc5_read(adc, ADC5_USR_DATA1, &rslt_msb, 1);
> + if (ret)
> + return ret;
> +
> + *data = (rslt_msb << 8) | rslt_lsb;
> +
> + if (*data == ADC5_USR_DATA_CHECK) {
> + pr_err("Invalid data:0x%x\n", *data);
> + return -EINVAL;
> + }
> +
> + return ret;
> +}
> +
> +static int adc5_poll_wait_eoc(struct adc5_chip *adc)
> +{
> + unsigned int count, retry = ADC5_CONV_TIME_RETRY;
> + u8 status1;
> + int ret;
> +
> + for (count = 0; count < retry; count++) {
> + ret = adc5_read(adc, ADC5_USR_STATUS1, &status1, 1);
> + if (ret)
> + return ret;
> +
> + status1 &= ADC5_USR_STATUS1_REQ_STS_EOC_MASK;
> + if (status1 == ADC5_USR_STATUS1_EOC)
> + return 0;
> + usleep_range(ADC5_CONV_TIME_MIN_US, ADC5_CONV_TIME_MAX_US);
> + }
> +
> + return -ETIMEDOUT;
> +}
> +
> +static void adc5_update_dig_param(struct adc5_chip *adc,
> + struct adc5_channel_prop *prop, u8 *data)
> +{
> + /* Update calibration value */
> + *data &= ~ADC5_USR_DIG_PARAM_CAL_VAL;
> + *data |= (prop->cal_val << ADC5_USR_DIG_PARAM_CAL_VAL_SHIFT);
> +
> + /* Update calibration select */
> + *data &= ~ADC5_USR_DIG_PARAM_CAL_SEL;
> + *data |= (prop->cal_method << ADC5_USR_DIG_PARAM_CAL_SEL_SHIFT);
> +
> + /* Update decimation ratio select */
> + *data &= ~ADC5_USR_DIG_PARAM_DEC_RATIO_SEL;
> + *data |= (prop->decimation << ADC5_USR_DIG_PARAM_DEC_RATIO_SEL_SHIFT);
> +}
> +
> +static int adc5_configure(struct adc5_chip *adc,
> + struct adc5_channel_prop *prop)
> +{
> + int ret;
> + u8 buf[6];
> +
> + /* Read registers 0x42 through 0x46 */
> + ret = adc5_read(adc, ADC5_USR_DIG_PARAM, buf, 6);
> + if (ret < 0)
> + return ret;
> +
> + /* Digital param selection */
> + adc5_update_dig_param(adc, prop, &buf[0]);
> +
> + /* Update fast average sample value */
> + buf[1] &= (u8) ~ADC5_USR_FAST_AVG_CTL_SAMPLES_MASK;
> + buf[1] |= prop->avg_samples;
> +
> + /* Select ADC channel */
> + buf[2] = prop->channel;
> +
> + /* Select HW settle delay for channel */
> + buf[3] &= (u8) ~ADC5_USR_HW_SETTLE_DELAY_MASK;
> + buf[3] |= prop->hw_settle_time;
> +
> + /* Select ADC enable */
> + buf[4] |= ADC5_USR_EN_CTL1_ADC_EN;
> +
> + /* Select CONV request */
> + buf[5] |= ADC5_USR_CONV_REQ_REQ;
> +
> + if (!adc->poll_eoc)
> + reinit_completion(&adc->complete);
> +
> + return adc5_write(adc, ADC5_USR_DIG_PARAM, buf, 6);
> +}
> +
> +static int adc5_do_conversion(struct adc5_chip *adc,
> + struct adc5_channel_prop *prop,
> + struct iio_chan_spec const *chan,
> + u16 *data_volt, u16 *data_cur)
> +{
> + int ret;
> +
> + mutex_lock(&adc->lock);
> +
> + ret = adc5_configure(adc, prop);
> + if (ret) {
> + pr_err("ADC configure failed with %d\n", ret);
> + goto unlock;
> + }
> +
> + if (adc->poll_eoc) {
> + ret = adc5_poll_wait_eoc(adc);
> + if (ret < 0) {
> + pr_err("EOC bit not set\n");
> + goto unlock;
> + }
> + } else {
> + ret = wait_for_completion_timeout(&adc->complete,
> + ADC5_CONV_TIMEOUT);
> + if (!ret) {
> + pr_debug("Did not get completion timeout.\n");
> + ret = adc5_poll_wait_eoc(adc);
> + if (ret < 0) {
> + pr_err("EOC bit not set\n");
> + goto unlock;
> + }
> + }
> + }
> +
> + if ((chan->type == IIO_VOLTAGE) || (chan->type == IIO_TEMP))
> + ret = adc5_read_voltage_data(adc, data_volt);
> + else if (chan->type == IIO_POWER) {
> + ret = adc5_read_voltage_data(adc, data_volt);
> + if (ret)
> + goto unlock;
> +
> + ret = adc5_read_current_data(adc, data_cur);
> + }
> +unlock:
> + mutex_unlock(&adc->lock);
> +
> + return ret;
> +}
> +
> +static irqreturn_t adc5_isr(int irq, void *dev_id)
> +{
> + struct adc5_chip *adc = dev_id;
> +
> + complete(&adc->complete);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static int adc5_of_xlate(struct iio_dev *indio_dev,
> + const struct of_phandle_args *iiospec)
> +{
> + struct adc5_chip *adc = iio_priv(indio_dev);
> + int i;
> +
> + for (i = 0; i < adc->nchannels; i++)
> + if (adc->chan_props[i].channel == iiospec->args[0])
> + return i;
> +
> + return -EINVAL;
> +}
> +
> +static int adc5_read_raw(struct iio_dev *indio_dev,
> + struct iio_chan_spec const *chan, int *val, int *val2,
> + long mask)
> +{
> + struct adc5_chip *adc = iio_priv(indio_dev);
> + struct adc5_channel_prop *prop;
> + u16 adc_code_volt, adc_code_cur;
> + int ret;
> +
> + prop = &adc->chan_props[chan->address];
> +
> + switch (mask) {
> + case IIO_CHAN_INFO_PROCESSED:
> + ret = adc5_do_conversion(adc, prop, chan,
> + &adc_code_volt, &adc_code_cur);
> + if (ret)
> + break;
> +
> + if ((chan->type == IIO_VOLTAGE) || (chan->type == IIO_TEMP))
> + ret = qcom_adc5_hw_scale(prop->scale_fn_type,
> + &adc5_prescale_ratios[prop->prescale],
> + adc->data,
> + adc_code_volt, val);
> + if (ret)
> + break;
> +
> + if (chan->type == IIO_POWER) {
> + ret = qcom_adc5_hw_scale(SCALE_HW_CALIB_DEFAULT,
> + &adc5_prescale_ratios[ADC5_DEF_VBAT_PRESCALING],
> + adc->data,
> + adc_code_volt, val);
> + if (ret)
> + break;
> +
> + ret = qcom_adc5_hw_scale(prop->scale_fn_type,
> + &adc5_prescale_ratios[prop->prescale],
> + adc->data,
> + adc_code_cur, val2);
> + if (ret)
> + break;
> + }
> +
> + if (chan->type == IIO_POWER)
> + return IIO_VAL_INT_MULTIPLE;
> + else
> + return IIO_VAL_INT;
> + case IIO_CHAN_INFO_RAW:
> + ret = adc5_do_conversion(adc, prop, chan,
> + &adc_code_volt, &adc_code_cur);
> + if (ret)
> + break;
> +
> + *val = (int)adc_code_volt;
> + *val2 = (int)adc_code_cur;
> + if (chan->type == IIO_POWER)
> + return IIO_VAL_INT_MULTIPLE;
I guess I missed this before. Why is this a multiple value set?
> + else
> + return IIO_VAL_INT;
> + default:
> + ret = -EINVAL;
> + break;
> + }
> +
> + return ret;
> +}
> +
> +static const struct iio_info adc5_info = {
> + .read_raw = adc5_read_raw,
> + .of_xlate = adc5_of_xlate,
> +};
> +
> +struct adc_channels {
> + const char *datasheet_name;
> + unsigned int prescale_index;
> + enum iio_chan_type type;
> + long info_mask;
> + enum vadc_scale_fn_type scale_fn_type;
> +};
> +
> +#define ADC5_CHAN(_dname, _type, _mask, _pre, _scale) \
> + { \
> + .datasheet_name = (_dname), \
> + .prescale_index = _pre, \
> + .type = _type, \
> + .info_mask = _mask, \
> + .scale_fn_type = _scale, \
> + }, \
> +
> +#define ADC5_CHAN_TEMP(_dname, _pre, _scale) \
> + ADC5_CHAN(_dname, IIO_TEMP, \
> + BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_PROCESSED), \
> + _pre, _scale) \
> +
> +#define ADC5_CHAN_VOLT(_dname, _pre, _scale) \
> + ADC5_CHAN(_dname, IIO_VOLTAGE, \
> + BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_PROCESSED),\
> + _pre, _scale) \
> +
> +#define ADC5_CHAN_POWER(_dname, _pre, _scale) \
> + ADC5_CHAN(_dname, IIO_POWER, \
> + BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_PROCESSED),\
> + _pre, _scale) \
> +
> +static const struct adc_channels adc_chans_pmic5[ADC5_MAX_CHANNEL] = {
> + [ADC5_REF_GND] = ADC5_CHAN_VOLT("ref_gnd", 1,
> + SCALE_HW_CALIB_DEFAULT)
> + [ADC5_1P25VREF] = ADC5_CHAN_VOLT("vref_1p25", 1,
> + SCALE_HW_CALIB_DEFAULT)
> + [ADC5_VPH_PWR] = ADC5_CHAN_VOLT("vph_pwr", 3,
> + SCALE_HW_CALIB_DEFAULT)
> + [ADC5_VBAT_SNS] = ADC5_CHAN_VOLT("vbat_sns", 3,
> + SCALE_HW_CALIB_DEFAULT)
> + [ADC5_DIE_TEMP] = ADC5_CHAN_TEMP("die_temp", 1,
> + SCALE_HW_CALIB_PMIC_THERM)
> + [ADC5_USB_IN_I] = ADC5_CHAN_VOLT("usb_in_i_uv", 1,
> + SCALE_HW_CALIB_DEFAULT)
> + [ADC5_USB_IN_V_16] = ADC5_CHAN_VOLT("usb_in_v_div_16", 16,
> + SCALE_HW_CALIB_DEFAULT)
> + [ADC5_CHG_TEMP] = ADC5_CHAN_TEMP("chg_temp", 1,
> + SCALE_HW_CALIB_PM5_CHG_TEMP)
> + /* Charger prescales SBUx and MID_CHG to fit within 1.8V upper unit */
> + [ADC5_SBUx] = ADC5_CHAN_VOLT("chg_sbux", 3,
> + SCALE_HW_CALIB_DEFAULT)
> + [ADC5_MID_CHG_DIV6] = ADC5_CHAN_VOLT("chg_mid_chg", 6,
> + SCALE_HW_CALIB_DEFAULT)
> + [ADC5_XO_THERM_100K_PU] = ADC5_CHAN_TEMP("xo_therm", 1,
> + SCALE_HW_CALIB_XOTHERM)
> + [ADC5_AMUX_THM1_100K_PU] = ADC5_CHAN_TEMP("amux_thm1_100k_pu", 1,
> + SCALE_HW_CALIB_THERM_100K_PULLUP)
> + [ADC5_AMUX_THM2_100K_PU] = ADC5_CHAN_TEMP("amux_thm2_100k_pu", 1,
> + SCALE_HW_CALIB_THERM_100K_PULLUP)
> + [ADC5_AMUX_THM3_100K_PU] = ADC5_CHAN_TEMP("amux_thm3_100k_pu", 1,
> + SCALE_HW_CALIB_THERM_100K_PULLUP)
> + [ADC5_INT_EXT_ISENSE_VBAT_VDATA] = ADC5_CHAN_POWER("int_ext_isense", 1,
> + SCALE_HW_CALIB_CUR)
> + [ADC5_EXT_ISENSE_VBAT_VDATA] = ADC5_CHAN_POWER("ext_isense", 1,
> + SCALE_HW_CALIB_CUR)
> + [ADC5_PARALLEL_ISENSE_VBAT_VDATA] =
> + ADC5_CHAN_POWER("parallel_isense", 1,
> + SCALE_HW_CALIB_CUR)
> + [ADC5_AMUX_THM2] = ADC5_CHAN_TEMP("amux_thm2", 1,
> + SCALE_HW_CALIB_PM5_SMB_TEMP)
> +};
> +
> +static const struct adc_channels adc_chans_rev2[ADC5_MAX_CHANNEL] = {
> + [ADC5_REF_GND] = ADC5_CHAN_VOLT("ref_gnd", 1,
> + SCALE_HW_CALIB_DEFAULT)
> + [ADC5_1P25VREF] = ADC5_CHAN_VOLT("vref_1p25", 1,
> + SCALE_HW_CALIB_DEFAULT)
> + [ADC5_VPH_PWR] = ADC5_CHAN_VOLT("vph_pwr", 3,
> + SCALE_HW_CALIB_DEFAULT)
> + [ADC5_VBAT_SNS] = ADC5_CHAN_VOLT("vbat_sns", 3,
> + SCALE_HW_CALIB_DEFAULT)
> + [ADC5_VCOIN] = ADC5_CHAN_VOLT("vcoin", 3,
> + SCALE_HW_CALIB_DEFAULT)
> + [ADC5_DIE_TEMP] = ADC5_CHAN_TEMP("die_temp", 1,
> + SCALE_HW_CALIB_PMIC_THERM)
> + [ADC5_AMUX_THM1_100K_PU] = ADC5_CHAN_TEMP("amux_thm1_100k_pu", 1,
> + SCALE_HW_CALIB_THERM_100K_PULLUP)
> + [ADC5_AMUX_THM3_100K_PU] = ADC5_CHAN_TEMP("amux_thm3_100k_pu", 1,
> + SCALE_HW_CALIB_THERM_100K_PULLUP)
> + [ADC5_AMUX_THM5_100K_PU] = ADC5_CHAN_TEMP("amux_thm5_100k_pu", 1,
> + SCALE_HW_CALIB_THERM_100K_PULLUP)
> + [ADC5_XO_THERM_100K_PU] = ADC5_CHAN_TEMP("xo_therm_100k_pu", 1,
> + SCALE_HW_CALIB_THERM_100K_PULLUP)
> +};
> +
> +static int adc5_get_dt_channel_data(struct adc5_chip *adc,
> + struct adc5_channel_prop *prop,
> + struct device_node *node,
> + const struct adc_data *data)
> +{
> + const char *name = node->name, *channel_name;
> + u32 chan, value, varr[2];
> + int ret;
> + struct device *dev = adc->dev;
> +
> + ret = of_property_read_u32(node, "reg", &chan);
> + if (ret) {
> + dev_err(dev, "invalid channel number %s\n", name);
> + return ret;
> + }
> +
> + if (chan > ADC5_PARALLEL_ISENSE_VBAT_IDATA) {
> + dev_err(dev, "%s invalid channel number %d\n", name, chan);
> + return -EINVAL;
> + }
> +
> + /* the channel has DT description */
> + prop->channel = chan;
> +
> + channel_name = of_get_property(node,
> + "label", NULL) ? : node->name;
> + if (!channel_name) {
> + pr_err("Invalid channel name\n");
> + return -EINVAL;
> + }
> + prop->datasheet_name = channel_name;
> +
> + ret = of_property_read_u32(node, "qcom,decimation", &value);
> + if (!ret) {
> + ret = adc5_decimation_from_dt(value, data->decimation);
> + if (ret < 0) {
> + dev_err(dev, "%02x invalid decimation %d\n",
> + chan, value);
> + return ret;
> + }
> + prop->decimation = ret;
> + } else {
> + prop->decimation = ADC5_DECIMATION_DEFAULT;
> + }
> +
> + ret = of_property_read_u32_array(node, "qcom,pre-scaling", varr, 2);
> + if (!ret) {
> + ret = adc5_prescaling_from_dt(varr[0], varr[1]);
> + if (ret < 0) {
> + dev_err(dev, "%02x invalid pre-scaling <%d %d>\n",
> + chan, varr[0], varr[1]);
> + return ret;
> + }
> + prop->prescale = ret;
> + }
> +
> + ret = of_property_read_u32(node, "qcom,hw-settle-time", &value);
> + if (!ret) {
> + u8 dig_version[2];
> +
> + ret = adc5_get_dig_version(adc, dig_version);
> + if (ret < 0) {
> + dev_err(dev, "Invalid dig version read %d\n", ret);
> + return ret;
> + }
> +
> + pr_debug("dig_ver:minor:%d, major:%d\n", dig_version[0],
> + dig_version[1]);
> + /* Digital controller >= 5.3 have hw_settle_2 option */
> + if (dig_version[0] >= ADC5_HW_SETTLE_DIFF_MINOR &&
> + dig_version[1] >= ADC5_HW_SETTLE_DIFF_MAJOR)
> + ret = adc5_hw_settle_time_from_dt(value,
> + data->hw_settle_2);
> + else
> + ret = adc5_hw_settle_time_from_dt(value,
> + data->hw_settle_1);
> +
> + if (ret < 0) {
> + dev_err(dev, "%02x invalid hw-settle-time %d us\n",
> + chan, value);
> + return ret;
> + }
> + prop->hw_settle_time = ret;
> + } else {
> + prop->hw_settle_time = VADC_DEF_HW_SETTLE_TIME;
> + }
> +
> + ret = of_property_read_u32(node, "qcom,avg-samples", &value);
> + if (!ret) {
> + ret = adc5_avg_samples_from_dt(value);
> + if (ret < 0) {
> + dev_err(dev, "%02x invalid avg-samples %d\n",
> + chan, value);
> + return ret;
> + }
> + prop->avg_samples = ret;
> + } else {
> + prop->avg_samples = VADC_DEF_AVG_SAMPLES;
> + }
> +
> + if (of_property_read_bool(node, "qcom,ratiometric"))
> + prop->cal_method = ADC5_RATIOMETRIC_CAL;
> + else
> + prop->cal_method = ADC5_ABSOLUTE_CAL;
> +
> + /*
> + * Default to using timer calibration. Using a fresh calibration value
> + * for every conversion will increase the overall time for a request.
> + */
> + prop->cal_val = ADC5_TIMER_CAL;
> +
> + dev_dbg(dev, "%02x name %s\n", chan, name);
> +
> + return 0;
> +}
> +
> +const struct adc_data data_pmic5 = {
> + .full_scale_code_volt = 0x70e4,
> + .full_scale_code_cur = 0x2710,
> + .adc_chans = adc_chans_pmic5,
> + .decimation = (unsigned int [ADC5_DECIMATION_SAMPLES_MAX])
> + {250, 420, 840},
> + .hw_settle_1 = (unsigned int [VADC_HW_SETTLE_SAMPLES_MAX])
> + {15, 100, 200, 300, 400, 500, 600, 700,
> + 800, 900, 1, 2, 4, 6, 8, 10},
> + .hw_settle_2 = (unsigned int [VADC_HW_SETTLE_SAMPLES_MAX])
> + {15, 100, 200, 300, 400, 500, 600, 700,
> + 1, 2, 4, 8, 16, 32, 64, 128},
> +};
> +
> +const struct adc_data data_pmic_rev2 = {
> + .full_scale_code_volt = 0x4000,
> + .full_scale_code_cur = 0x1800,
> + .adc_chans = adc_chans_rev2,
> + .decimation = (unsigned int [ADC5_DECIMATION_SAMPLES_MAX])
> + {256, 512, 1024},
> + .hw_settle_1 = (unsigned int [VADC_HW_SETTLE_SAMPLES_MAX])
> + {0, 100, 200, 300, 400, 500, 600, 700,
> + 800, 900, 1, 2, 4, 6, 8, 10},
> + .hw_settle_2 = (unsigned int [VADC_HW_SETTLE_SAMPLES_MAX])
> + {15, 100, 200, 300, 400, 500, 600, 700,
> + 1, 2, 4, 8, 16, 32, 64, 128},
> +};
> +
> +static const struct of_device_id adc5_match_table[] = {
> + {
> + .compatible = "qcom,spmi-adc5",
> + .data = &data_pmic5,
> + },
> + {
> + .compatible = "qcom,spmi-adc-rev2",
> + .data = &data_pmic_rev2,
> + },
> + { }
> +};
> +
> +static int adc5_get_dt_data(struct adc5_chip *adc, struct device_node *node)
> +{
> + const struct adc_channels *adc_chan;
> + struct iio_chan_spec *iio_chan;
> + struct adc5_channel_prop prop;
> + struct device_node *child;
> + unsigned int index = 0;
> + const struct of_device_id *id;
> + const struct adc_data *data;
> + int ret;
> +
> + adc->nchannels = of_get_available_child_count(node);
> + if (!adc->nchannels)
> + return -EINVAL;
> +
> + adc->iio_chans = devm_kcalloc(adc->dev, adc->nchannels,
> + sizeof(*adc->iio_chans), GFP_KERNEL);
> + if (!adc->iio_chans)
> + return -ENOMEM;
> +
> + adc->chan_props = devm_kcalloc(adc->dev, adc->nchannels,
> + sizeof(*adc->chan_props), GFP_KERNEL);
> + if (!adc->chan_props)
> + return -ENOMEM;
> +
> + iio_chan = adc->iio_chans;
> + id = of_match_node(adc5_match_table, node);
> + if (id)
> + data = id->data;
> + else
> + data = &data_pmic5;
> + adc->data = data;
> +
> + for_each_available_child_of_node(node, child) {
> + ret = adc5_get_dt_channel_data(adc, &prop, child, data);
> + if (ret) {
> + of_node_put(child);
> + return ret;
> + }
> +
> + prop.scale_fn_type =
> + data->adc_chans[prop.channel].scale_fn_type;
> + adc->chan_props = ∝
> + adc_chan = &data->adc_chans[prop.channel];
> +
> + iio_chan->channel = prop.channel;
> + iio_chan->datasheet_name = prop.datasheet_name;
> + iio_chan->extend_name = prop.datasheet_name;
> + iio_chan->info_mask_separate = adc_chan->info_mask;
> + iio_chan->type = adc_chan->type;
> + iio_chan->address = index;
> + iio_chan++;
> + adc->chan_props++;
> + index++;
> + }
> +
> + return 0;
> +}
> +
> +static int adc5_probe(struct platform_device *pdev)
> +{
> + struct device_node *node = pdev->dev.of_node;
> + struct device *dev = &pdev->dev;
> + struct iio_dev *indio_dev;
> + struct adc5_chip *adc;
> + struct regmap *regmap;
> + int ret, irq_eoc;
> + u32 reg;
> +
> + regmap = dev_get_regmap(dev->parent, NULL);
> + if (!regmap)
> + return -ENODEV;
> +
> + ret = of_property_read_u32(node, "reg", ®);
> + if (ret < 0)
> + return ret;
> +
> + indio_dev = devm_iio_device_alloc(dev, sizeof(*adc));
> + if (!indio_dev)
> + return -ENOMEM;
> +
> + adc = iio_priv(indio_dev);
> + adc->regmap = regmap;
> + adc->dev = dev;
> + adc->base = reg;
> + init_completion(&adc->complete);
> + mutex_init(&adc->lock);
> +
> + ret = adc5_get_dt_data(adc, node);
> + if (ret) {
> + pr_err("adc get dt data failed\n");
> + return ret;
> + }
> +
> + irq_eoc = platform_get_irq(pdev, 0);
> + if (irq_eoc < 0) {
> + if (irq_eoc == -EPROBE_DEFER || irq_eoc == -EINVAL)
> + return irq_eoc;
> + adc->poll_eoc = true;
> + } else {
> + ret = devm_request_irq(dev, irq_eoc, adc5_isr, 0,
> + "pm-adc5", adc);
> + if (ret)
> + return ret;
> + }
> +
> + indio_dev->dev.parent = dev;
> + indio_dev->dev.of_node = node;
> + indio_dev->name = pdev->name;
> + indio_dev->modes = INDIO_DIRECT_MODE;
> + indio_dev->info = &adc5_info;
> + indio_dev->channels = adc->iio_chans;
> + indio_dev->num_channels = adc->nchannels;
> +
> + return devm_iio_device_register(dev, indio_dev);
> +}
> +
> +static struct platform_driver adc5_driver = {
> + .driver = {
> + .name = "qcom-spmi-adc5.c",
> + .of_match_table = adc5_match_table,
> + },
> + .probe = adc5_probe,
> +};
> +module_platform_driver(adc5_driver);
> +
> +MODULE_ALIAS("platform:qcom-spmi-adc5");
> +MODULE_DESCRIPTION("Qualcomm Technologies Inc. PMIC5 ADC driver");
> +MODULE_LICENSE("GPL v2");
> diff --git a/drivers/iio/adc/qcom-vadc-common.c b/drivers/iio/adc/qcom-vadc-common.c
> index fe3d782..e430f6e 100644
> --- a/drivers/iio/adc/qcom-vadc-common.c
> +++ b/drivers/iio/adc/qcom-vadc-common.c
> @@ -47,8 +47,85 @@
> {44, 125}
> };
>
> +/*
> + * Voltage to temperature table for 100k pull up for NTCG104EF104 with
> + * 1.875V reference.
> + */
> +static const struct vadc_map_pt adcmap_100k_104ef_104fb_1875_vref[] = {
> + { 1831, -40000 },
> + { 1814, -35000 },
> + { 1791, -30000 },
> + { 1761, -25000 },
> + { 1723, -20000 },
> + { 1675, -15000 },
> + { 1616, -10000 },
> + { 1545, -5000 },
> + { 1463, 0 },
> + { 1370, 5000 },
> + { 1268, 10000 },
> + { 1160, 15000 },
> + { 1049, 20000 },
> + { 937, 25000 },
> + { 828, 30000 },
> + { 726, 35000 },
> + { 630, 40000 },
> + { 544, 45000 },
> + { 467, 50000 },
> + { 399, 55000 },
> + { 340, 60000 },
> + { 290, 65000 },
> + { 247, 70000 },
> + { 209, 75000 },
> + { 179, 80000 },
> + { 153, 85000 },
> + { 130, 90000 },
> + { 112, 95000 },
> + { 96, 100000 },
> + { 82, 105000 },
> + { 71, 110000 },
> + { 62, 115000 },
> + { 53, 120000 },
> + { 46, 125000 },
> +};
> +
> +static int qcom_vadc_scale_hw_calib_volt(
> + const struct vadc_prescale_ratio *prescale,
> + const struct adc_data *data,
> + u16 adc_code, int *result_uv);
> +static int qcom_vadc_scale_hw_calib_therm(
> + const struct vadc_prescale_ratio *prescale,
> + const struct adc_data *data,
> + u16 adc_code, int *result_mdec);
> +static int qcom_vadc_scale_hw_smb_temp(
> + const struct vadc_prescale_ratio *prescale,
> + const struct adc_data *data,
> + u16 adc_code, int *result_mdec);
> +static int qcom_vadc_scale_hw_chg5_temp(
> + const struct vadc_prescale_ratio *prescale,
> + const struct adc_data *data,
> + u16 adc_code, int *result_mdec);
> +static int qcom_vadc_scale_hw_calib_die_temp(
> + const struct vadc_prescale_ratio *prescale,
> + const struct adc_data *data,
> + u16 adc_code, int *result_mdec);
> +static int qcom_adc_scale_hw_calib_cur(
> + const struct vadc_prescale_ratio *prescale,
> + const struct adc_data *data,
> + u16 adc_code, int *result_uamps);
> +
> +
> +static struct qcom_adc5_scale_type scale_adc5_fn[] = {
> + [SCALE_HW_CALIB_DEFAULT] = {qcom_vadc_scale_hw_calib_volt},
> + [SCALE_HW_CALIB_THERM_100K_PULLUP] = {qcom_vadc_scale_hw_calib_therm},
> + [SCALE_HW_CALIB_XOTHERM] = {qcom_vadc_scale_hw_calib_therm},
> + [SCALE_HW_CALIB_PMIC_THERM] = {qcom_vadc_scale_hw_calib_die_temp},
> + [SCALE_HW_CALIB_PM5_CHG_TEMP] = {qcom_vadc_scale_hw_chg5_temp},
> + [SCALE_HW_CALIB_PM5_SMB_TEMP] = {qcom_vadc_scale_hw_smb_temp},
> + [SCALE_HW_CALIB_CUR] = {qcom_adc_scale_hw_calib_cur},
> +};
> +
> static int qcom_vadc_map_voltage_temp(const struct vadc_map_pt *pts,
> - u32 tablesize, s32 input, s64 *output)
> + u32 tablesize, s32 input, int *output)
> {
> bool descending = 1;
> u32 i = 0;
> @@ -128,7 +205,7 @@ static int qcom_vadc_scale_therm(const struct vadc_linear_graph *calib_graph,
> bool absolute, u16 adc_code,
> int *result_mdec)
> {
> - s64 voltage = 0, result = 0;
> + s64 voltage = 0;
> int ret;
>
> qcom_vadc_scale_calib(calib_graph, adc_code, absolute, &voltage);
> @@ -138,12 +215,11 @@ static int qcom_vadc_scale_therm(const struct vadc_linear_graph *calib_graph,
>
> ret = qcom_vadc_map_voltage_temp(adcmap_100k_104ef_104fb,
> ARRAY_SIZE(adcmap_100k_104ef_104fb),
> - voltage, &result);
> + voltage, result_mdec);
> if (ret)
> return ret;
>
> - result *= 1000;
> - *result_mdec = result;
> + *result_mdec *= 1000;
>
> return 0;
> }
> @@ -191,6 +267,134 @@ static int qcom_vadc_scale_chg_temp(const struct vadc_linear_graph *calib_graph,
> return 0;
> }
>
> +static int qcom_vadc_scale_code_voltage_factor(u16 adc_code,
> + const struct vadc_prescale_ratio *prescale,
> + const struct adc_data *data,
> + unsigned int factor)
> +{
> + s64 voltage, temp, adc_vdd_ref_mv = 1875;
> +
> + /*
> + * The normal data range is between 0V to 1.875V. On cases where
> + * we read low voltage values, the ADC code can go beyond the
> + * range and the scale result is incorrect so we clamp the values
> + * for the cases where the code represents a value below 0V
> + */
> + if (adc_code > VADC5_MAX_CODE)
> + adc_code = 0;
> +
> + /* (ADC code * vref_vadc (1.875V)) / full_scale_code */
> + voltage = (s64) adc_code * adc_vdd_ref_mv * 1000;
> + voltage = div64_s64(voltage, data->full_scale_code_volt);
> + if (voltage > 0) {
> + voltage *= prescale->den;
> + temp = prescale->num * factor;
> + voltage = div64_s64(voltage, temp);
> + } else {
> + voltage = 0;
> + }
> +
> + return (int) voltage;
> +}
> +
> +static int qcom_vadc_scale_hw_calib_volt(
> + const struct vadc_prescale_ratio *prescale,
> + const struct adc_data *data,
> + u16 adc_code, int *result_uv)
> +{
> + *result_uv = qcom_vadc_scale_code_voltage_factor(adc_code,
> + prescale, data, 1);
> +
> + return 0;
> +}
> +
> +static int qcom_vadc_scale_hw_calib_therm(
> + const struct vadc_prescale_ratio *prescale,
> + const struct adc_data *data,
> + u16 adc_code, int *result_mdec)
> +{
> + int ret, voltage;
> +
> + voltage = qcom_vadc_scale_code_voltage_factor(adc_code,
> + prescale, data, 1000);
> +
> + /* Map voltage to temperature from look-up table */
> + ret = qcom_vadc_map_voltage_temp(adcmap_100k_104ef_104fb_1875_vref,
> + ARRAY_SIZE(adcmap_100k_104ef_104fb_1875_vref),
> + voltage, result_mdec);
return qcom_vadc_map_voltage...
> + if (ret)
> + return ret;
> +
> + return 0;
> +}
> +
> +static int qcom_vadc_scale_hw_calib_die_temp(
> + const struct vadc_prescale_ratio *prescale,
> + const struct adc_data *data,
> + u16 adc_code, int *result_mdec)
> +{
> + *result_mdec = qcom_vadc_scale_code_voltage_factor(adc_code,
> + prescale, data, 2);
> + *result_mdec -= KELVINMIL_CELSIUSMIL;
> +
> + return 0;
> +}
> +
> +static int qcom_vadc_scale_hw_smb_temp(
> + const struct vadc_prescale_ratio *prescale,
> + const struct adc_data *data,
> + u16 adc_code, int *result_mdec)
> +{
> + *result_mdec = qcom_vadc_scale_code_voltage_factor(adc_code * 100,
> + prescale, data, PMIC5_SMB_TEMP_SCALE_FACTOR);
> + *result_mdec = PMIC5_SMB_TEMP_CONSTANT - *result_mdec;
> +
> + return 0;
> +}
> +
> +static int qcom_vadc_scale_hw_chg5_temp(
> + const struct vadc_prescale_ratio *prescale,
> + const struct adc_data *data,
> + u16 adc_code, int *result_mdec)
> +{
> + *result_mdec = qcom_vadc_scale_code_voltage_factor(adc_code,
> + prescale, data, 4);
> + *result_mdec = PMIC5_CHG_TEMP_SCALE_FACTOR - *result_mdec;
> +
> + return 0;
> +}
> +
> +static int qcom_adc_scale_hw_calib_cur(
> + const struct vadc_prescale_ratio *prescale,
> + const struct adc_data *data,
> + u16 adc_code, int *result_uamps)
> +{
> + s64 voltage;
> +
> + /*
> + * The measurement data is provided in 2's complement format
> + * with the polarity convention as positive current (current
> + * going out of the battery) and negative current
> + * (current going into the battery).
> + *
> + * If MSB is set, convert the negative number to decimal,
> + * apply scaling factor and place negative sign in front
> + * of the final result.
> + */
> + if (adc_code & ADC5_USR_DATA_CHECK)
> + adc_code = ~adc_code + 1;
> +
> + voltage = (s64) adc_code * data->full_scale_code_cur * 1000;
> + voltage = div64_s64(voltage, VADC5_MAX_CODE);
> + voltage = voltage * prescale->den;
> + *result_uamps = (int) div64_s64(voltage, prescale->num);
> +
> + if (adc_code & ADC5_USR_DATA_CHECK)
> + *result_uamps = -*result_uamps;
> +
> + return 0;
> +}
> +
> int qcom_vadc_scale(enum vadc_scale_fn_type scaletype,
> const struct vadc_linear_graph *calib_graph,
> const struct vadc_prescale_ratio *prescale,
> @@ -221,6 +425,22 @@ int qcom_vadc_scale(enum vadc_scale_fn_type scaletype,
> }
> EXPORT_SYMBOL(qcom_vadc_scale);
>
> +int qcom_adc5_hw_scale(enum vadc_scale_fn_type scaletype,
> + const struct vadc_prescale_ratio *prescale,
> + const struct adc_data *data,
> + u16 adc_code, int *result)
> +{
> + if (!(scaletype >= SCALE_HW_CALIB_DEFAULT &&
> + scaletype < SCALE_HW_CALIB_INVALID)) {
> + pr_err("Invalid scale type %d\n", scaletype);
> + return -EINVAL;
> + }
> +
> + return scale_adc5_fn[scaletype].scale_fn(prescale, data,
> + adc_code, result);
> +}
> +EXPORT_SYMBOL(qcom_adc5_hw_scale);
> +
> int qcom_vadc_decimation_from_dt(u32 value)
> {
> if (!is_power_of_2(value) || value < VADC_DECIMATION_MIN ||
> diff --git a/drivers/iio/adc/qcom-vadc-common.h b/drivers/iio/adc/qcom-vadc-common.h
> index 1d5354f..1051720 100644
> --- a/drivers/iio/adc/qcom-vadc-common.h
> +++ b/drivers/iio/adc/qcom-vadc-common.h
> @@ -25,15 +25,31 @@
>
> #define VADC_DECIMATION_MIN 512
> #define VADC_DECIMATION_MAX 4096
> +#define ADC5_DEF_VBAT_PRESCALING 1 /* 1:3 */
> +#define ADC5_DECIMATION_SHORT 250
> +#define ADC5_DECIMATION_MEDIUM 420
> +#define ADC5_DECIMATION_LONG 840
> +/* Default decimation - 1024 for rev2, 840 for pmic5 */
> +#define ADC5_DECIMATION_DEFAULT 2
> +#define ADC5_DECIMATION_SAMPLES_MAX 3
>
> #define VADC_HW_SETTLE_DELAY_MAX 10000
> +#define VADC_HW_SETTLE_SAMPLES_MAX 16
> #define VADC_AVG_SAMPLES_MAX 512
> +#define ADC5_AVG_SAMPLES_MAX 16
>
> #define KELVINMIL_CELSIUSMIL 273150
> +#define PMIC5_CHG_TEMP_SCALE_FACTOR 377500
> +#define PMIC5_SMB_TEMP_CONSTANT 419400
> +#define PMIC5_SMB_TEMP_SCALE_FACTOR 356
>
> #define PMI_CHG_SCALE_1 -138890
> #define PMI_CHG_SCALE_2 391750000000LL
>
> +#define VADC5_MAX_CODE 0x7fff
> +#define ADC5_FULL_SCALE_CODE 0x70e4
> +#define ADC5_USR_DATA_CHECK 0x8000
> +
> /**
> * struct vadc_map_pt - Map the graph representation for ADC channel
> * @x: Represent the ADC digitized code.
> @@ -89,6 +105,19 @@ struct vadc_prescale_ratio {
> * SCALE_PMIC_THERM: Returns result in milli degree's Centigrade.
> * SCALE_XOTHERM: Returns XO thermistor voltage in millidegC.
> * SCALE_PMI_CHG_TEMP: Conversion for PMI CHG temp
> + * SCALE_HW_CALIB_DEFAULT: Default scaling to convert raw adc code to
> + * voltage (uV) with hardware applied offset/slope values to adc code.
> + * SCALE_HW_CALIB_THERM_100K_PULLUP: Returns temperature in millidegC using
> + * lookup table. The hardware applies offset/slope to adc code.
> + * SCALE_HW_CALIB_XOTHERM: Returns XO thermistor voltage in millidegC using
> + * 100k pullup. The hardware applies offset/slope to adc code.
> + * SCALE_HW_CALIB_PMIC_THERM: Returns result in milli degree's Centigrade.
> + * The hardware applies offset/slope to adc code.
> + * SCALE_HW_CALIB_CUR: Returns result in uA for PMIC5.
> + * SCALE_HW_CALIB_PM5_CHG_TEMP: Returns result in millidegrees for PMIC5
> + * charger temperature.
> + * SCALE_HW_CALIB_PM5_SMB_TEMP: Returns result in millidegrees for PMIC5
> + * SMB1390 temperature.
> */
> enum vadc_scale_fn_type {
> SCALE_DEFAULT = 0,
> @@ -96,6 +125,23 @@ enum vadc_scale_fn_type {
> SCALE_PMIC_THERM,
> SCALE_XOTHERM,
> SCALE_PMI_CHG_TEMP,
> + SCALE_HW_CALIB_DEFAULT,
> + SCALE_HW_CALIB_THERM_100K_PULLUP,
> + SCALE_HW_CALIB_XOTHERM,
> + SCALE_HW_CALIB_PMIC_THERM,
> + SCALE_HW_CALIB_CUR,
> + SCALE_HW_CALIB_PM5_CHG_TEMP,
> + SCALE_HW_CALIB_PM5_SMB_TEMP,
> + SCALE_HW_CALIB_INVALID,
> +};
> +
> +struct adc_data {
> + const u32 full_scale_code_volt;
> + const u32 full_scale_code_cur;
> + const struct adc_channels *adc_chans;
> + unsigned int *decimation;
> + unsigned int *hw_settle_1;
> + unsigned int *hw_settle_2;
> };
>
> int qcom_vadc_scale(enum vadc_scale_fn_type scaletype,
> @@ -104,6 +150,16 @@ int qcom_vadc_scale(enum vadc_scale_fn_type scaletype,
> bool absolute,
> u16 adc_code, int *result_mdec);
>
> +struct qcom_adc5_scale_type {
> + int (*scale_fn)(const struct vadc_prescale_ratio *prescale,
> + const struct adc_data *data, u16 adc_code, int *result);
> +};
> +
> +int qcom_adc5_hw_scale(enum vadc_scale_fn_type scaletype,
> + const struct vadc_prescale_ratio *prescale,
> + const struct adc_data *data,
> + u16 adc_code, int *result_mdec);
> +
> int qcom_vadc_decimation_from_dt(u32 value);
>
> #endif /* QCOM_VADC_COMMON_H */
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
