Add support for the drive strength configuration. Usually, this value is expressed in mA. Since the numeric value depends on VDDIOP voltage, a value we can't retrieve at runtime, the controller uses low, medium and high to define the drive strength. The PIO controller accepts two values for the low drive configuration: 0 and 1. Most of the time, we don't care about the drive strength. So we keep the default value which is 0. The drive strength is advertised through the sysfs only when it has been explicitly set in the device tree i.e. if its value is different from 0. Signed-off-by: Ludovic Desroches <ludovic.desroches@xxxxxxxxxxxxx> --- Changes: - v2: use atmel,drive-strength property instead of drive-strengh one since it is not expressend in mA and there is no way to retrieve this value at runtime. - v1: https://www.spinics.net/lists/linux-gpio/msg27789.html .../bindings/pinctrl/atmel,at91-pio4-pinctrl.txt | 3 ++ drivers/pinctrl/pinctrl-at91-pio4.c | 42 ++++++++++++++++++++++ include/dt-bindings/pinctrl/at91.h | 4 +++ 3 files changed, 49 insertions(+) diff --git a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pio4-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pio4-pinctrl.txt index 61ac75706cc9..04d16fb69eb7 100644 --- a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pio4-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pio4-pinctrl.txt @@ -36,6 +36,8 @@ Optional properties: - GENERIC_PINCONFIG: generic pinconfig options to use, bias-disable, bias-pull-down, bias-pull-up, drive-open-drain, input-schmitt-enable, input-debounce, output-low, output-high. +- atmel,drive-strength: 0 or 1 for low drive, 2 for medium drive and 3 for +high drive. The default value is low drive. Example: @@ -66,6 +68,7 @@ Example: pinmux = <PIN_PB0>, <PIN_PB5>; bias-pull-up; + atmel,drive-strength = <ATMEL_PIO_DRVSTR_ME>; }; pinctrl_sdmmc1_default: sdmmc1_default { diff --git a/drivers/pinctrl/pinctrl-at91-pio4.c b/drivers/pinctrl/pinctrl-at91-pio4.c index 67e4d9ffa6b1..8f061971a7d1 100644 --- a/drivers/pinctrl/pinctrl-at91-pio4.c +++ b/drivers/pinctrl/pinctrl-at91-pio4.c @@ -14,6 +14,7 @@ * GNU General Public License for more details. */ +#include <dt-bindings/pinctrl/at91.h> #include <linux/clk.h> #include <linux/gpio/driver.h> /* FIXME: needed for gpio_to_irq(), get rid of this */ @@ -49,6 +50,8 @@ #define ATMEL_PIO_IFSCEN_MASK BIT(13) #define ATMEL_PIO_OPD_MASK BIT(14) #define ATMEL_PIO_SCHMITT_MASK BIT(15) +#define ATMEL_PIO_DRVSTR_MASK GENMASK(17, 16) +#define ATMEL_PIO_DRVSTR_OFFSET 16 #define ATMEL_PIO_CFGR_EVTSEL_MASK GENMASK(26, 24) #define ATMEL_PIO_CFGR_EVTSEL_FALLING (0 << 24) #define ATMEL_PIO_CFGR_EVTSEL_RISING (1 << 24) @@ -75,6 +78,9 @@ #define ATMEL_GET_PIN_FUNC(pinfunc) ((pinfunc >> 16) & 0xf) #define ATMEL_GET_PIN_IOSET(pinfunc) ((pinfunc >> 20) & 0xf) +/* Custom pinconf parameters */ +#define ATMEL_PIN_CONFIG_DRIVE_STRENGTH (PIN_CONFIG_END + 1) + struct atmel_pioctrl_data { unsigned nbanks; }; @@ -139,6 +145,10 @@ static const char * const atmel_functions[] = { "GPIO", "A", "B", "C", "D", "E", "F", "G" }; +static const struct pinconf_generic_params atmel_custom_bindings[] = { + {"atmel,drive-strength", ATMEL_PIN_CONFIG_DRIVE_STRENGTH, 0}, +}; + /* --- GPIO --- */ static unsigned int atmel_gpio_read(struct atmel_pioctrl *atmel_pioctrl, unsigned int bank, unsigned int reg) @@ -692,6 +702,11 @@ static int atmel_conf_pin_config_group_get(struct pinctrl_dev *pctldev, return -EINVAL; arg = 1; break; + case ATMEL_PIN_CONFIG_DRIVE_STRENGTH: + if (!(res & ATMEL_PIO_DRVSTR_MASK)) + return -EINVAL; + arg = (res & ATMEL_PIO_DRVSTR_MASK) >> ATMEL_PIO_DRVSTR_OFFSET; + break; default: return -ENOTSUPP; } @@ -777,6 +792,18 @@ static int atmel_conf_pin_config_group_set(struct pinctrl_dev *pctldev, ATMEL_PIO_SODR); } break; + case ATMEL_PIN_CONFIG_DRIVE_STRENGTH: + switch (arg) { + case ATMEL_PIO_DRVSTR_LO: + case ATMEL_PIO_DRVSTR_ME: + case ATMEL_PIO_DRVSTR_HI: + conf &= (~ATMEL_PIO_DRVSTR_MASK); + conf |= arg << ATMEL_PIO_DRVSTR_OFFSET; + break; + default: + dev_warn(pctldev->dev, "drive strength not updated (incorrect value)\n"); + } + break; default: dev_warn(pctldev->dev, "unsupported configuration parameter: %u\n", @@ -816,6 +843,19 @@ static void atmel_conf_pin_config_dbg_show(struct pinctrl_dev *pctldev, seq_printf(s, "%s ", "open-drain"); if (conf & ATMEL_PIO_SCHMITT_MASK) seq_printf(s, "%s ", "schmitt"); + if (conf & ATMEL_PIO_DRVSTR_MASK) { + switch ((conf & ATMEL_PIO_DRVSTR_MASK) >> ATMEL_PIO_DRVSTR_OFFSET) { + case ATMEL_PIO_DRVSTR_ME: + seq_printf(s, "%s ", "medium-drive"); + break; + case ATMEL_PIO_DRVSTR_HI: + seq_printf(s, "%s ", "high-drive"); + break; + /* ATMEL_PIO_DRVSTR_LO and 0 which is the default value at reset */ + default: + seq_printf(s, "%s ", "low-drive"); + } + } } static const struct pinconf_ops atmel_confops = { @@ -958,6 +998,8 @@ static int atmel_pinctrl_probe(struct platform_device *pdev) return -ENOMEM; atmel_pinctrl_desc.pins = pin_desc; atmel_pinctrl_desc.npins = atmel_pioctrl->npins; + atmel_pinctrl_desc.num_custom_params = ARRAY_SIZE(atmel_custom_bindings); + atmel_pinctrl_desc.custom_params = atmel_custom_bindings; /* One pin is one group since a pin can achieve all functions. */ group_names = devm_kcalloc(dev, diff --git a/include/dt-bindings/pinctrl/at91.h b/include/dt-bindings/pinctrl/at91.h index 2732d6c0fb39..eb81867eac77 100644 --- a/include/dt-bindings/pinctrl/at91.h +++ b/include/dt-bindings/pinctrl/at91.h @@ -39,4 +39,8 @@ #define AT91_PERIPH_C 3 #define AT91_PERIPH_D 4 +#define ATMEL_PIO_DRVSTR_LO 1 +#define ATMEL_PIO_DRVSTR_ME 2 +#define ATMEL_PIO_DRVSTR_HI 3 + #endif /* __DT_BINDINGS_AT91_PINCTRL_H__ */ -- 2.12.2 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
