Implement the base virtio-iommu driver, following version 0.7 of the
specification [1].
Changes since last version [2]:
* Address comments, thanks again for the review.
* As suggested, add a DT binding description in patch 1.
* Depend on VIRTIO_MMIO=y to fix a build failure¹
* Switch to v0.7 of the spec, which changes resv_mem parameters and adds
an MMIO flag. These are trivial but not backward compatible. Once
device or driver is upstream, updates to the spec will rely on feature
bits to stay compatible with this code.
* Implement the new tlb_sync interface, by splitting add_req() and
sync_req(). I noticed a small improvement on netperf stream because
the synchronous iommu_unmap() also benefits from this. Other
experiments, such as using kmem_cache for requests instead of kmalloc,
didn't show any improvement.
Driver is available on branch virtio-iommu/v0.7 [3], and the x86+ACPI
prototype is on branch virtio-iommu/devel. That x86 code hasn't changed,
it still requires the DMA ifdeffery and I lack the expertise to tidy it
up. The kvmtool example device has been cleaned up and is available on
branch virtio-iommu/v0.7 [4].
Feedback welcome!
Thanks,
Jean
[1] virtio-iommu specification v0.7
https://www.spinics.net/lists/linux-virtualization/msg34127.html
[2] virtio-iommu driver v1
https://www.spinics.net/lists/kvm/msg164322.html
[3] git://linux-arm.org/linux-jpb.git virtio-iommu/v0.7
http://www.linux-arm.org/git?p=linux-jpb.git;a=shortlog;h=refs/heads/virtio-iommu/v0.7
[4] git://linux-arm.org/kvmtool-jpb.git virtio-iommu/v0.7
---
¹ A word on the module story. Because of complex dependencies IOMMU
drivers cannot yet be .ko modules. Enabling it is outside the scope of
this series but I have a small prototype on branch virtio-iommu/
module-devel. It seems desirable since some distros currently ship the
transport code as module and are unlikely to change this on our account.
Note that this series works fine with arm64 defconfig, which selects
VIRTIO_MMIO=y.
I could use some help to clean this up. Currently my solution is to split
virtio-iommu into a module and a 3-lines built-in stub, which isn't
graceful but could have been worse.
Keeping the whole virtio-iommu driver as builtin would require accessing
any virtio utility through get_symbol. So far we only have seven of
those and could keep a list of pointer ops, but I find this solution
terrible. If virtio or virtio_mmio is a module, virtio-iommu also needs
to be one.
The minimal set of changes to make a module out of an OF-based IOMMU
driver seems to be:
* Export IOMMU symbols used by drivers
* Don't give up deferring probe in of_iommu
* Move IOMMU OF tables to .rodata
* Create a static virtio-iommu stub that declares the virtio-iommu OF
table entry. The build system doesn't pick up IOMMU_OF_DECLARE when
done from an object destined to be built as module :(
* Create a device_link between endpoint and IOMMU, to ensure that
removing the IOMMU driver also unbinds the endpoint driver. Putting
this in IOMMU core seems like a better approach since even when not
built as module, unbinding an IOMMU device via sysfs will cause
crashes.
With this, as long as virtio-mmio isn't loaded, the OF code defers probe
of endpoints that depend on virtio-iommu. Once virtio-mmio is loaded,
the probe is still deferred until virtio-iommu registers itself to the
virtio bus. Once virtio-iommu is loaded, probe of endpoints managed by
the IOMMU follows.
I'll investigate ACPI IORT when I find some time, though I don't expect
much complication and suggest we tackle one problem at a time. Since it
is a luxury that requires changes to the IOMMU core, module support is
left as a future improvement.
---
Jean-Philippe Brucker (5):
dt-bindings: virtio: Specify #iommu-cells value for a virtio-iommu
iommu: Add virtio-iommu driver
iommu/virtio: Add probe request
iommu/virtio: Add event queue
vfio: Allow type-1 IOMMU instantiation for ARM
.../devicetree/bindings/virtio/mmio.txt | 8 +
MAINTAINERS | 6 +
drivers/iommu/Kconfig | 11 +
drivers/iommu/Makefile | 1 +
drivers/iommu/virtio-iommu.c | 1164 +++++++++++++++++
drivers/vfio/Kconfig | 2 +-
include/uapi/linux/virtio_ids.h | 1 +
include/uapi/linux/virtio_iommu.h | 172 +++
8 files changed, 1364 insertions(+), 1 deletion(-)
create mode 100644 drivers/iommu/virtio-iommu.c
create mode 100644 include/uapi/linux/virtio_iommu.h
--
2.17.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
