RE: [PATCH V2 1/3] scsi: ufs: set the device reference clock setting

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Rob,

Please check my comment inline.

Thanks,
Sayali
-----Original Message-----
From: Rob Herring [mailto:robh@xxxxxxxxxx] 
Sent: Thursday, June 14, 2018 7:59 PM
To: sayali <sayalil@xxxxxxxxxxxxxx>
Cc: Subhash Jadavani <subhashj@xxxxxxxxxxxxxx>; Can Guo <cang@xxxxxxxxxxxxxx>; Vivek Gautam <vivek.gautam@xxxxxxxxxxxxxx>; Rajendra Nayak <rnayak@xxxxxxxxxxxxxx>; Vinayak Holikatti <vinholikatti@xxxxxxxxx>; James E.J. Bottomley <jejb@xxxxxxxxxxxxxxxxxx>; Martin K. Petersen <martin.petersen@xxxxxxxxxx>; asutoshd@xxxxxxxxxxxxxx; Evan Green <evgreen@xxxxxxxxxxxx>; linux-scsi@xxxxxxxxxxxxxxx; Mark Rutland <mark.rutland@xxxxxxx>; Mathieu Malaterre <malat@xxxxxxxxxx>; open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS <devicetree@xxxxxxxxxxxxxxx>; open list <linux-kernel@xxxxxxxxxxxxxxx>
Subject: Re: [PATCH V2 1/3] scsi: ufs: set the device reference clock setting

On Thu, Jun 14, 2018 at 5:33 AM, sayali <sayalil@xxxxxxxxxxxxxx> wrote:
> Comment inline.
>
> Thanks,
> Sayali
> -----Original Message-----
> From: Rob Herring [mailto:robh@xxxxxxxxxx]
> Sent: Wednesday, June 13, 2018 12:57 AM
> To: Sayali Lokhande <sayalil@xxxxxxxxxxxxxx>
> Cc: subhashj@xxxxxxxxxxxxxx; cang@xxxxxxxxxxxxxx; 
> vivek.gautam@xxxxxxxxxxxxxx; rnayak@xxxxxxxxxxxxxx; 
> vinholikatti@xxxxxxxxx; jejb@xxxxxxxxxxxxxxxxxx; 
> martin.petersen@xxxxxxxxxx; asutoshd@xxxxxxxxxxxxxx; 
> evgreen@xxxxxxxxxxxx; linux-scsi@xxxxxxxxxxxxxxx; Mark Rutland 
> <mark.rutland@xxxxxxx>; Mathieu Malaterre <malat@xxxxxxxxxx>; open 
> list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS 
> <devicetree@xxxxxxxxxxxxxxx>; open list <linux-kernel@xxxxxxxxxxxxxxx>
> Subject: Re: [PATCH V2 1/3] scsi: ufs: set the device reference clock 
> setting
>
> On Fri, Jun 08, 2018 at 04:36:28PM +0530, Sayali Lokhande wrote:
>> From: Subhash Jadavani <subhashj@xxxxxxxxxxxxxx>
>>
>> UFS host supplies the reference clock to UFS device and UFS device 
>> specification allows host to provide one of the 4 frequencies (19.2 
>> MHz,
>> 26 MHz, 38.4 MHz, 52 MHz) for reference clock. Host should set the 
>> device reference clock frequency setting in the device based on what 
>> frequency it is supplying to UFS device.
>>
>> Signed-off-by: Subhash Jadavani <subhashj@xxxxxxxxxxxxxx>
>> Signed-off-by: Can Guo <cang@xxxxxxxxxxxxxx>
>> Signed-off-by: Sayali Lokhande <sayalil@xxxxxxxxxxxxxx>
>> ---
>>  .../devicetree/bindings/ufs/ufshcd-pltfrm.txt      |  7 +++
>>  drivers/scsi/ufs/ufs.h                             |  9 ++++
>>  drivers/scsi/ufs/ufshcd-pltfrm.c                   | 24 ++++++++++
>>  drivers/scsi/ufs/ufshcd.c                          | 52
> ++++++++++++++++++++++
>>  drivers/scsi/ufs/ufshcd.h                          |  1 +
>>  5 files changed, 93 insertions(+)
>>
>> diff --git a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
>> b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
>> index c39dfef..4522434 100644
>> --- a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
>> +++ b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
>> @@ -41,6 +41,12 @@ Optional properties:
>>  -lanes-per-direction : number of lanes available per direction - 
>> either 1
> or 2.
>>                         Note that it is assume same number of lanes 
>> is
> used both
>>                         directions at once. If not specified, default 
>> is 2
> lanes per direction.
>> +- dev-ref-clk-freq   : Specify the device reference clock frequency, must
> be one of the following:
>> +                       0: 19.2 MHz
>> +                       1: 26 MHz
>> +                       2: 38.4 MHz
>> +                       3: 52 MHz
>> +                       Defaults to 26 MHz if not specified.
>
> I must have misunderstood your last response. I thought you could 
> handle things without DT. If not, my question remains.
> [Sayali]: Ref clk frequency setting could vary from 
> platfrom-to-platform(vendor specific). Hence we need to pass it via DT.
>         Currently in DT we do not set/mention any ref clk frequency 
> parameter. Hence I have added one new DT entry to configure
>         required ref clk freq.

The clocks property contains "ref_clk". Is that not the same clock?
Why can't you read what that frequency is? Or you need to be able to change it to a specific frequency? These all look like typical oscillator frequencies, so I wouldn't expect you could change them (other than divide by 2 maybe).
[Sayali] : It is the same "ref_clk", but we need to be able to change it to a specific frequency as per requirement. Thus, we need new DT entry to specify/override reference clock frequency as per need.

Rob

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux