Comment inline. Thanks, Sayali -----Original Message----- From: Rob Herring [mailto:robh@xxxxxxxxxx] Sent: Wednesday, June 13, 2018 12:57 AM To: Sayali Lokhande <sayalil@xxxxxxxxxxxxxx> Cc: subhashj@xxxxxxxxxxxxxx; cang@xxxxxxxxxxxxxx; vivek.gautam@xxxxxxxxxxxxxx; rnayak@xxxxxxxxxxxxxx; vinholikatti@xxxxxxxxx; jejb@xxxxxxxxxxxxxxxxxx; martin.petersen@xxxxxxxxxx; asutoshd@xxxxxxxxxxxxxx; evgreen@xxxxxxxxxxxx; linux-scsi@xxxxxxxxxxxxxxx; Mark Rutland <mark.rutland@xxxxxxx>; Mathieu Malaterre <malat@xxxxxxxxxx>; open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS <devicetree@xxxxxxxxxxxxxxx>; open list <linux-kernel@xxxxxxxxxxxxxxx> Subject: Re: [PATCH V2 1/3] scsi: ufs: set the device reference clock setting On Fri, Jun 08, 2018 at 04:36:28PM +0530, Sayali Lokhande wrote: > From: Subhash Jadavani <subhashj@xxxxxxxxxxxxxx> > > UFS host supplies the reference clock to UFS device and UFS device > specification allows host to provide one of the 4 frequencies (19.2 > MHz, > 26 MHz, 38.4 MHz, 52 MHz) for reference clock. Host should set the > device reference clock frequency setting in the device based on what > frequency it is supplying to UFS device. > > Signed-off-by: Subhash Jadavani <subhashj@xxxxxxxxxxxxxx> > Signed-off-by: Can Guo <cang@xxxxxxxxxxxxxx> > Signed-off-by: Sayali Lokhande <sayalil@xxxxxxxxxxxxxx> > --- > .../devicetree/bindings/ufs/ufshcd-pltfrm.txt | 7 +++ > drivers/scsi/ufs/ufs.h | 9 ++++ > drivers/scsi/ufs/ufshcd-pltfrm.c | 24 ++++++++++ > drivers/scsi/ufs/ufshcd.c | 52 ++++++++++++++++++++++ > drivers/scsi/ufs/ufshcd.h | 1 + > 5 files changed, 93 insertions(+) > > diff --git a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt > b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt > index c39dfef..4522434 100644 > --- a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt > +++ b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt > @@ -41,6 +41,12 @@ Optional properties: > -lanes-per-direction : number of lanes available per direction - either 1 or 2. > Note that it is assume same number of lanes is used both > directions at once. If not specified, default is 2 lanes per direction. > +- dev-ref-clk-freq : Specify the device reference clock frequency, must be one of the following: > + 0: 19.2 MHz > + 1: 26 MHz > + 2: 38.4 MHz > + 3: 52 MHz > + Defaults to 26 MHz if not specified. I must have misunderstood your last response. I thought you could handle things without DT. If not, my question remains. [Sayali]: Ref clk frequency setting could vary from platfrom-to-platform(vendor specific). Hence we need to pass it via DT. Currently in DT we do not set/mention any ref clk frequency parameter. Hence I have added one new DT entry to configure required ref clk freq. Rob -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
