Hi Sakari,
I'm fine with the change to dev_fwnode(&client->dev).
Many thanks Sakari,
Hugues.
On 06/11/2018 12:10 PM, Sakari Ailus wrote:
> On Mon, Jun 11, 2018 at 11:29:17AM +0200, Hugues Fruchet wrote:
>> Add support of module being physically mounted upside down.
>> In this case, mirror and flip are enabled to fix captured images
>> orientation.
>>
>> Signed-off-by: Hugues Fruchet <hugues.fruchet@xxxxxx>
>> ---
>> .../devicetree/bindings/media/i2c/ov5640.txt | 3 +++
>> drivers/media/i2c/ov5640.c | 28 ++++++++++++++++++++--
>> 2 files changed, 29 insertions(+), 2 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/media/i2c/ov5640.txt b/Documentation/devicetree/bindings/media/i2c/ov5640.txt
>> index 8e36da0..f76eb7e 100644
>> --- a/Documentation/devicetree/bindings/media/i2c/ov5640.txt
>> +++ b/Documentation/devicetree/bindings/media/i2c/ov5640.txt
>> @@ -13,6 +13,8 @@ Optional Properties:
>> This is an active low signal to the OV5640.
>> - powerdown-gpios: reference to the GPIO connected to the powerdown pin,
>> if any. This is an active high signal to the OV5640.
>> +- rotation: integer property; valid values are 0 (sensor mounted upright)
>> + and 180 (sensor mounted upside down).
>>
>> The device node must contain one 'port' child node for its digital output
>> video port, in accordance with the video interface bindings defined in
>> @@ -51,6 +53,7 @@ Examples:
>> DVDD-supply = <&vgen2_reg>; /* 1.5v */
>> powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
>> reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
>> + rotation = <180>;
>>
>> port {
>> /* MIPI CSI-2 bus endpoint */
>> diff --git a/drivers/media/i2c/ov5640.c b/drivers/media/i2c/ov5640.c
>> index 41039e5..5529b14 100644
>> --- a/drivers/media/i2c/ov5640.c
>> +++ b/drivers/media/i2c/ov5640.c
>> @@ -215,6 +215,7 @@ struct ov5640_dev {
>> struct regulator_bulk_data supplies[OV5640_NUM_SUPPLIES];
>> struct gpio_desc *reset_gpio;
>> struct gpio_desc *pwdn_gpio;
>> + bool upside_down;
>>
>> /* lock to protect all members below */
>> struct mutex lock;
>> @@ -2222,6 +2223,8 @@ static int ov5640_set_ctrl_light_freq(struct ov5640_dev *sensor, int value)
>> static int ov5640_set_ctrl_hflip(struct ov5640_dev *sensor, int value)
>> {
>> /*
>> + * If sensor is mounted upside down, mirror logic is inversed.
>> + *
>> * Sensor is a BSI (Back Side Illuminated) one,
>> * so image captured is physically mirrored.
>> * This is why mirror logic is inversed in
>> @@ -2235,11 +2238,14 @@ static int ov5640_set_ctrl_hflip(struct ov5640_dev *sensor, int value)
>> */
>> return ov5640_mod_reg(sensor, OV5640_REG_TIMING_TC_REG21,
>> BIT(2) | BIT(1),
>> - (!value) ? (BIT(2) | BIT(1)) : 0);
>> + (!(value ^ sensor->upside_down)) ?
>> + (BIT(2) | BIT(1)) : 0);
>> }
>>
>> static int ov5640_set_ctrl_vflip(struct ov5640_dev *sensor, int value)
>> {
>> + /* If sensor is mounted upside down, flip logic is inversed */
>> +
>> /*
>> * TIMING TC REG20:
>> * - [2]: ISP vflip
>> @@ -2247,7 +2253,8 @@ static int ov5640_set_ctrl_vflip(struct ov5640_dev *sensor, int value)
>> */
>> return ov5640_mod_reg(sensor, OV5640_REG_TIMING_TC_REG20,
>> BIT(2) | BIT(1),
>> - value ? (BIT(2) | BIT(1)) : 0);
>> + (value ^ sensor->upside_down) ?
>> + (BIT(2) | BIT(1)) : 0);
>> }
>>
>> static int ov5640_g_volatile_ctrl(struct v4l2_ctrl *ctrl)
>> @@ -2625,6 +2632,7 @@ static int ov5640_probe(struct i2c_client *client,
>> struct fwnode_handle *endpoint;
>> struct ov5640_dev *sensor;
>> struct v4l2_mbus_framefmt *fmt;
>> + u32 rotation;
>> int ret;
>>
>> sensor = devm_kzalloc(dev, sizeof(*sensor), GFP_KERNEL);
>> @@ -2650,6 +2658,22 @@ static int ov5640_probe(struct i2c_client *client,
>>
>> sensor->ae_target = 52;
>>
>> + /* optional indication of physical rotation of sensor */
>> + ret = fwnode_property_read_u32(of_fwnode_handle(client->dev.of_node),
>
> Instead of of_fwnode_handle(), please use dev_fwnode(&client->dev) --- as the
> driver already does elsewhere.
>
> I can make the change if you're happy with that; the patches seem fine
> otherwise.
>
>> + "rotation", &rotation);
>> + if (!ret) {
>> + switch (rotation) {
>> + case 180:
>> + sensor->upside_down = true;
>> + /* fall through */
>> + case 0:
>> + break;
>> + default:
>> + dev_warn(dev, "%u degrees rotation is not supported, ignoring...\n",
>> + rotation);
>> + }
>> + }
>> +
>> endpoint = fwnode_graph_get_next_endpoint(dev_fwnode(&client->dev),
>> NULL);
>> if (!endpoint) {
> ��.n��������+%������w��{.n����z�{��ܨ}���Ơz�j:+v�����w����ޙ��&�)ߡ�a����z�ޗ���ݢj��w�f
