On Mon, Jun 11, 2018 at 11:29:17AM +0200, Hugues Fruchet wrote:
> Add support of module being physically mounted upside down.
> In this case, mirror and flip are enabled to fix captured images
> orientation.
>
> Signed-off-by: Hugues Fruchet <hugues.fruchet@xxxxxx>
> ---
> .../devicetree/bindings/media/i2c/ov5640.txt | 3 +++
> drivers/media/i2c/ov5640.c | 28 ++++++++++++++++++++--
> 2 files changed, 29 insertions(+), 2 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/media/i2c/ov5640.txt b/Documentation/devicetree/bindings/media/i2c/ov5640.txt
> index 8e36da0..f76eb7e 100644
> --- a/Documentation/devicetree/bindings/media/i2c/ov5640.txt
> +++ b/Documentation/devicetree/bindings/media/i2c/ov5640.txt
> @@ -13,6 +13,8 @@ Optional Properties:
> This is an active low signal to the OV5640.
> - powerdown-gpios: reference to the GPIO connected to the powerdown pin,
> if any. This is an active high signal to the OV5640.
> +- rotation: integer property; valid values are 0 (sensor mounted upright)
> + and 180 (sensor mounted upside down).
>
> The device node must contain one 'port' child node for its digital output
> video port, in accordance with the video interface bindings defined in
> @@ -51,6 +53,7 @@ Examples:
> DVDD-supply = <&vgen2_reg>; /* 1.5v */
> powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
> reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
> + rotation = <180>;
>
> port {
> /* MIPI CSI-2 bus endpoint */
> diff --git a/drivers/media/i2c/ov5640.c b/drivers/media/i2c/ov5640.c
> index 41039e5..5529b14 100644
> --- a/drivers/media/i2c/ov5640.c
> +++ b/drivers/media/i2c/ov5640.c
> @@ -215,6 +215,7 @@ struct ov5640_dev {
> struct regulator_bulk_data supplies[OV5640_NUM_SUPPLIES];
> struct gpio_desc *reset_gpio;
> struct gpio_desc *pwdn_gpio;
> + bool upside_down;
>
> /* lock to protect all members below */
> struct mutex lock;
> @@ -2222,6 +2223,8 @@ static int ov5640_set_ctrl_light_freq(struct ov5640_dev *sensor, int value)
> static int ov5640_set_ctrl_hflip(struct ov5640_dev *sensor, int value)
> {
> /*
> + * If sensor is mounted upside down, mirror logic is inversed.
> + *
> * Sensor is a BSI (Back Side Illuminated) one,
> * so image captured is physically mirrored.
> * This is why mirror logic is inversed in
> @@ -2235,11 +2238,14 @@ static int ov5640_set_ctrl_hflip(struct ov5640_dev *sensor, int value)
> */
> return ov5640_mod_reg(sensor, OV5640_REG_TIMING_TC_REG21,
> BIT(2) | BIT(1),
> - (!value) ? (BIT(2) | BIT(1)) : 0);
> + (!(value ^ sensor->upside_down)) ?
> + (BIT(2) | BIT(1)) : 0);
> }
>
> static int ov5640_set_ctrl_vflip(struct ov5640_dev *sensor, int value)
> {
> + /* If sensor is mounted upside down, flip logic is inversed */
> +
> /*
> * TIMING TC REG20:
> * - [2]: ISP vflip
> @@ -2247,7 +2253,8 @@ static int ov5640_set_ctrl_vflip(struct ov5640_dev *sensor, int value)
> */
> return ov5640_mod_reg(sensor, OV5640_REG_TIMING_TC_REG20,
> BIT(2) | BIT(1),
> - value ? (BIT(2) | BIT(1)) : 0);
> + (value ^ sensor->upside_down) ?
> + (BIT(2) | BIT(1)) : 0);
> }
>
> static int ov5640_g_volatile_ctrl(struct v4l2_ctrl *ctrl)
> @@ -2625,6 +2632,7 @@ static int ov5640_probe(struct i2c_client *client,
> struct fwnode_handle *endpoint;
> struct ov5640_dev *sensor;
> struct v4l2_mbus_framefmt *fmt;
> + u32 rotation;
> int ret;
>
> sensor = devm_kzalloc(dev, sizeof(*sensor), GFP_KERNEL);
> @@ -2650,6 +2658,22 @@ static int ov5640_probe(struct i2c_client *client,
>
> sensor->ae_target = 52;
>
> + /* optional indication of physical rotation of sensor */
> + ret = fwnode_property_read_u32(of_fwnode_handle(client->dev.of_node),
Instead of of_fwnode_handle(), please use dev_fwnode(&client->dev) --- as the
driver already does elsewhere.
I can make the change if you're happy with that; the patches seem fine
otherwise.
> + "rotation", &rotation);
> + if (!ret) {
> + switch (rotation) {
> + case 180:
> + sensor->upside_down = true;
> + /* fall through */
> + case 0:
> + break;
> + default:
> + dev_warn(dev, "%u degrees rotation is not supported, ignoring...\n",
> + rotation);
> + }
> + }
> +
> endpoint = fwnode_graph_get_next_endpoint(dev_fwnode(&client->dev),
> NULL);
> if (!endpoint) {
--
Kind regards,
Sakari Ailus
e-mail: sakari.ailus@xxxxxx
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
