From: Martin Sperl <kernel@xxxxxxxxxxxxxxxx>
This patchset adds a driver for the mcp25xxfd CanFD controller.
Most of the features of the controller are supported by this
driver release.
The controller includes a few features that the current core Can(FD)
implementation does not support:
* Transmit Bandwidth Sharing bits
- this waits for a configurable number of syncronization bits before
atempting to transmit the next frame - for the moment controllable
via a module parameter
* SID11 with CanFD frames
- at this moment not supported by driver
* 3 transmit attempts in addition to ONE_SHOT
* transmitter delay compensation configurations
* micro second exact transmission and reception timestamps
- used internally by driver
* variable number of tx-fifos
- exposed via module parameter at this moment
The driver has been heavily optimized so that it can handle
a 100% utilized 1MHz Can-bus (with 11 bit can frames with DLC=0)
even on less powerful SOCs like the raspberry pi 1 without
dropping frames due to driver/spi latencies (still dropps
are observed in the can/network stack).
To achive this the driver includes several code optimization
Two of which prefers continuous long spi transfers over multiple
small individual spi transfers of variable length.
This is an optimization that would favour spi dma transfers instead
of more expensive PIO in typical SPI controllers.
Both of them can get explicitly enabled by the use of a module parameter.
One of those is automatically used in the case of Can2.0 only bus
configurations.
Finer details of the implementation and rational is included with
the driver code it self for future reference.
The driver has also been tested for basic CanFD transfers with
BRS up to 5.7Mhz data bitrates - the available transceiver did
not allow for faster rates...
The driver itself exposes lots of internal data/statistics via
debugfs.
The driver implements a lock-less design for transmissions
making use instead of prepared spi messages submitted via spi_async
for transmission in the start_xmit_start code without requireing
an extra workqueue and the corresponding latencies.
Note that there is an extra patch in the pipeline to implement pinctrl
but this still shows some issues, so it is not included in this patchset.
Changelog:
V1 -> V2: new more generic name based on feedback from microchip
cleanup of code (checkpatch)
address all feedback on code
handle (HW) systemerrors in a much better/reliable way
cleanup of dt custom properties removing (most) gpio
related properties
implemented GPIOLIB support as per feedback
V2 -> V3: added vendor-prefix for gpio-opendrain to dt-binding
added gpio-controller to dt-binding
added feedback by Rob Herring
waited for other feedback regarding the code
V3 -> V4: resend
Patch-1 (dt) added: Reviewed-by: Rob Herring <robh@xxxxxxxxxx>
Martin Sperl (3):
dt-binding: can: mcp25xxfd: document device tree bindings
can: mcp25xxfd: Add Microchip mcp25xxfd CAN FD driver
can: mcp25xxfd: add gpiolib support for GPIO0/1 (aka. INT0/INT1)
.../bindings/net/can/microchip,mcp25xxfd.txt | 32 +
drivers/net/can/spi/Kconfig | 6 +
drivers/net/can/spi/Makefile | 1 +
drivers/net/can/spi/mcp25xxfd.c | 4509 ++++++++++++++++++++
4 files changed, 4548 insertions(+)
create mode 100644 Documentation/devicetree/bindings/net/can/microchip,mcp25xxfd.txt
create mode 100644 drivers/net/can/spi/mcp25xxfd.c
--
2.11.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
