Add a DT binding documentation of XS-PHY for MediaTek SoCs
with USB3.1 GEN2 controller
Signed-off-by: Chunfeng Yun <chunfeng.yun@xxxxxxxxxxxx>
---
.../devicetree/bindings/phy/phy-mtk-xsphy.txt | 110 ++++++++++++++++++++
1 file changed, 110 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/phy-mtk-xsphy.txt
diff --git a/Documentation/devicetree/bindings/phy/phy-mtk-xsphy.txt b/Documentation/devicetree/bindings/phy/phy-mtk-xsphy.txt
new file mode 100644
index 0000000..7f2b16f
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/phy-mtk-xsphy.txt
@@ -0,0 +1,110 @@
+MediaTek XS-PHY binding
+--------------------------
+
+The XS-PHY controller supports physical layer functionality for USB3.1
+GEN2 controller on MediaTek SoCs.
+
+Required properties (controller (parent) node):
+ - compatible : should be "mediatek,<soc-model>-xsphy", "mediatek,xsphy",
+ soc-model is the name of SoC, such as mt3611 etc;
+ when using "mediatek,xsphy" compatible string, you need SoC specific
+ ones in addition, one of:
+ - "mediatek,mt3611-xsphy"
+
+ - #address-cells, #size-cells : should use the same values as the root node
+ - ranges: must be present
+
+Optional properties (controller (parent) node):
+ - reg : offset and length of register shared by multiple U3 ports,
+ exclude port's private register, if only U2 ports provided,
+ shouldn't use the property.
+ - mediatek,src-ref-clk-mhz : u32, frequency of reference clock for slew rate
+ calibrate
+ - mediatek,src-coef : u32, coefficient for slew rate calibrate, depends on
+ SoC process
+
+Required nodes : a sub-node is required for each port the controller
+ provides. Address range information including the usual
+ 'reg' property is used inside these nodes to describe
+ the controller's topology.
+
+Required properties (port (child) node):
+- reg : address and length of the register set for the port.
+- clocks : a list of phandle + clock-specifier pairs, one for each
+ entry in clock-names
+- clock-names : must contain
+ "ref": 48M reference clock for HighSpeed analog phy; and 26M
+ reference clock for SuperSpeedPlus analog phy, sometimes is
+ 24M, 25M or 27M, depended on platform.
+- #phy-cells : should be 1
+ cell after port phandle is phy type from:
+ - PHY_TYPE_USB2
+ - PHY_TYPE_USB3
+
+The following optional properties are only for debug or HQA test
+Optional properties (PHY_TYPE_USB2 port (child) node):
+- mediatek,eye-src : u32, the value of slew rate calibrate
+- mediatek,eye-vrt : u32, the selection of VRT reference voltage
+- mediatek,eye-term : u32, the selection of HS_TX TERM reference voltage
+- mediatek,efuse-intr : u32, the selection of Internal Resistor
+
+Optional properties (PHY_TYPE_USB3 port (child) node):
+- mediatek,efuse-intr : u32, the selection of Internal Resistor
+- mediatek,efuse-tx-imp : u32, the selection of TX Impedance
+- mediatek,efuse-rx-imp : u32, the selection of RX Impedance
+
+Banks layout of xsphy
+-------------------------------------------------------------
+port offset bank
+u2 port0 0x0000 MISC
+ 0x0100 FMREG
+ 0x0300 U2PHY_COM
+u2 port1 0x1000 MISC
+ 0x1100 FMREG
+ 0x1300 U2PHY_COM
+u2 port2 0x2000 MISC
+ ...
+u31 common 0x3000 DIG_GLB
+ 0x3100 PHYA_GLB
+u31 port0 0x3400 DIG_LN_TOP
+ 0x3500 DIG_LN_TX0
+ 0x3600 DIG_LN_RX0
+ 0x3700 DIG_LN_DAIF
+ 0x3800 PHYA_LN
+u31 port1 0x3a00 DIG_LN_TOP
+ 0x3b00 DIG_LN_TX0
+ 0x3c00 DIG_LN_RX0
+ 0x3d00 DIG_LN_DAIF
+ 0x3e00 PHYA_LN
+ ...
+
+DIG_GLB & PHYA_GLB are shared by U31 ports.
+
+Example:
+
+u3phy: usb-phy@11c40000 {
+ compatible = "mediatek,mt3611-xsphy", "mediatek,xsphy";
+ reg = <0 0x11c43000 0 0x0200>;
+ mediatek,src-ref-clk-mhz = <26>;
+ mediatek,src-coef = <17>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ u2port0: usb-phy@11c40000 {
+ reg = <0 0x11c40000 0 0x0400>;
+ clocks = <&clk48m>;
+ clock-names = "ref";
+ mediatek,eye-src = <4>;
+ #phy-cells = <1>;
+ };
+
+ u3port0: usb-phy@11c43000 {
+ reg = <0 0x11c43400 0 0x0500>;
+ clocks = <&clk26m>;
+ clock-names = "ref";
+ mediatek,efuse-intr = <28>;
+ #phy-cells = <1>;
+ };
+};
+
--
1.7.9.5
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
