Hi Randy,
On Tue 08 May 2018 at 17:24, Randy Dunlap wrote:
Hi,
I have a few editing suggestions below...
Thank you very much for this. I will incorporate this in the next
version.
---
Cheers,
Rui
On 05/07/2018 09:21 AM, Rui Miguel Silva wrote:
Add rst document to describe the i.MX7 media driver and also a
working example
from the Warp7 board usage with a OV2680 sensor.
Signed-off-by: Rui Miguel Silva <rui.silva@xxxxxxxxxx>
---
Documentation/media/v4l-drivers/imx7.rst | 157
++++++++++++++++++++++
Documentation/media/v4l-drivers/index.rst | 1 +
2 files changed, 158 insertions(+)
create mode 100644 Documentation/media/v4l-drivers/imx7.rst
diff --git a/Documentation/media/v4l-drivers/imx7.rst
b/Documentation/media/v4l-drivers/imx7.rst
new file mode 100644
index 000000000000..64b97b442277
--- /dev/null
+++ b/Documentation/media/v4l-drivers/imx7.rst
@@ -0,0 +1,157 @@
+i.MX7 Video Capture Driver
+==========================
+
+Introduction
+------------
+
+The i.MX7 contrary to the i.MX5/6 family does not contain an
Image Processing
+Unit (IPU), because of that the capabilities to perform
operations or
s/,/;/
+manipulation of the capture frames is less feature rich.
are less
+
+For image capture the i.MX7 have three units:
has
+- CMOS Sensor Interface (CSI)
+- Video Multiplexer
+- MIPI CSI-2 Receiver
+
+::
+ |\
+ MIPI Camera Input ---> MIPI CSI-2 --- > | \
+ | \
+ | M |
+ | U | ------> CSI
---> Capture
+ | X |
+ | /
+ Parallel Camera Input ----------------> | /
+ |/
+
+For additional information, please refer to the latest
versions of the i.MX7
+reference manual [#f1]_.
+
+Entities
+--------
+
+imx7-mipi-csi2
+--------------
+
+This is the MIPI CSI-2 recevier entity. It has one sink pad to
receive the pixel
receiver
+data from MIPI CSI-2 camera sensor. It has one source pad,
corresponding to the
+virtual channel 0. This module is compliant to previous
version of Samsung
+D-phy, and support two D-PHY Rx Data lanes.
supports
+
+csi_mux
+-------
+
+This is the video multiplexer. It has two sink pads to select
from either camera
+sensors with a parallel interface or from MIPI CSI-2 virtual
channel 0. It has
sensor
+a single source pad that routes to the CSI.
+
+csi
+---
+
+The CSI enables the chip to connect directly to external CMOS
image sensor. CSI
+can interfaces directly with Parallel and MIPI CSI-2 buses. It
has 256 x 64 FIFO
interface
+to store received image pixel data and embedded DMA
controllers to transfer data
+from the FIFO through AHB bus.
+
+This entity has one sink pad that receive from the csi_mux
entity and a single
receives
+source pad that route video frames directly to memory buffers,
this pad is
routes
buffers. This pad is
+routed to a capture device node.
+
+Usage Notes
+-----------
+
+To aid in configuration and for backward compatibility with
V4L2 applications
+that access controls only from video device nodes, the capture
device interfaces
+inherit controls from the active entities in the current
pipeline, so controls
+can be accessed either directly from the subdev or from the
active capture
+device interface. For example, the sensor controls are
available either from the
+sensor subdevs or from the active capture device.
+
+Warp7 with OV2680
+-----------------
+
+On this platform an OV2680 MIPI CSI-2 module is connected to
the internal MIPI
+CSI-2 receiver. The following example configures a video
capture pipeline with
+an output of 800x600, and BGGR 10 bit bayer format:
+
+.. code-block:: none
+ # Setup links
+ media-ctl -l "'ov2680 1-0036':0 -> 'imx7-mipi-csis.0':0[1]"
+ media-ctl -l "'imx7-mipi-csis.0':1 -> 'csi_mux':1[1]"
+ media-ctl -l "'csi_mux':2 -> 'csi':0[1]"
+ media-ctl -l "'csi':1 -> 'csi capture':0[1]"
+
+ # Configure pads for pipeline
+ media-ctl -V "'ov2680 1-0036':0 [fmt:SBGGR10_1X10/800x600
field:none]"
+ media-ctl -V "'csi_mux':1 [fmt:SBGGR10_1X10/800x600
field:none]"
+ media-ctl -V "'csi_mux':2 [fmt:SBGGR10_1X10/800x600
field:none]"
+ media-ctl -V "'imx7-mipi-csis.0':0
[fmt:SBGGR10_1X10/800x600 field:none]"
+ media-ctl -V "'csi':0 [fmt:SBGGR10_1X10/800x600
field:none]"
+
+After this streaming can start, the v4l2-ctl tool can be used
to select any of
can start. The
+the resolutions supported by the sensor.
+
+.. code-block:: none
+ root@imx7s-warp:~# media-ctl -p
+ Media controller API version 4.17.0
+
+ Media device information
+ ------------------------
+ driver imx-media
+ model imx-media
+ serial
+ bus info
+ hw revision 0x0
+ driver version 4.17.0
+
+ Device topology
+ - entity 1: csi (2 pads, 2 links)
+ type V4L2 subdev subtype Unknown flags 0
+ device node name /dev/v4l-subdev0
+ pad0: Sink
+ [fmt:SBGGR10_1X10/800x600 field:none]
+ <- "csi_mux":2 [ENABLED]
+ pad1: Source
+ [fmt:SBGGR10_1X10/800x600 field:none]
+ -> "csi capture":0 [ENABLED]
+
+ - entity 4: csi capture (1 pad, 1 link)
+ type Node subtype V4L flags 0
+ device node name /dev/video0
+ pad0: Sink
+ <- "csi":1 [ENABLED]
+
+ - entity 10: csi_mux (3 pads, 2 links)
+ type V4L2 subdev subtype Unknown flags 0
+ device node name /dev/v4l-subdev1
+ pad0: Sink
+ [fmt:unknown/0x0]
+ pad1: Sink
+ [fmt:unknown/800x600 field:none]
+ <- "imx7-mipi-csis.0":1 [ENABLED]
+ pad2: Source
+ [fmt:unknown/800x600 field:none]
+ -> "csi":0 [ENABLED]
+
+ - entity 14: imx7-mipi-csis.0 (2 pads, 2 links)
+ type V4L2 subdev subtype Unknown flags 0
+ device node name /dev/v4l-subdev2
+ pad0: Sink
+ [fmt:SBGGR10_1X10/800x600 field:none]
+ <- "ov2680 1-0036":0 [ENABLED]
+ pad1: Source
+ [fmt:SBGGR10_1X10/800x600 field:none]
+ -> "csi_mux":1 [ENABLED]
+
+ - entity 17: ov2680 1-0036 (1 pad, 1 link)
+ type V4L2 subdev subtype Sensor flags 0
+ device node name /dev/v4l-subdev3
+ pad0: Source
+ [fmt:SBGGR10_1X10/800x600 field:none]
+ -> "imx7-mipi-csis.0":0 [ENABLED]
+
+
+References
+----------
+
+.. [#f1]
https://www.nxp.com/docs/en/reference-manual/IMX7SRM.pdf
thanks.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
