* Pavel Machek <pavel@xxxxxx> [180329 18:07]: > On Thu 2018-03-29 09:34:50, Tony Lindgren wrote: > > * Pavel Machek <pavel@xxxxxx> [180329 16:09]: > > > > Then using the n_gsm ts 27.010 uart mux, I dial: > > > > > > > > ./ngsm-rw 1 "AT+CFUN=1" # connect to network > > > > U0001+CFUN:OK > > > > ./ngsm-rw 2 "AT+CMUT=0" # unmute speaker over ch2, do this over qmi? > > > > U0001+CMUT:OK > > > > ./ngsm-rw 1 "ATD#123" # dial number > > > > U0001D:OK > > > > > > > > And I do hear a voice talking over the speakerphone :) Sorry have not tested the > > > > mic yet.. > > > > > > Hehe, ok, that's fun! I don't need +CMUT=0. It gave me error but then > > > the call worked, anyway... (I'm working with ttyUSB4). > > > > Oh interesting. So maybe Android is doing AT+CMUT=0 for some other > > modems and it's not really needed? Or you have settings preserved > > from warm boot from Android? > > No idea. But I booted from recovery, and I had to power up modem using > +CFUN... > > > I did not have any luck with ttyUSB4 last night. Did you dial with > > ATD123; or ATD123? So is the semicolon really needed? > > > > AT+CFUN=1 > OK > ATD800123456 > NO CARRIER > ATD800123456; > OK > > I seem to need semicolon. And yes, I tried again after the call. Still > says no carrier. OK thanks for confirming that. > Hmm. And when calling test number, the modem failed: > > > [ 438.236755] Somebody do a proper driver please cpcap_soc_work > [ 495.496032] phy-mapphone-mdm6600 usb-phy@1: modem status: 0 off > [ 499.406005] phy-mapphone-mdm6600 usb-phy@1: modem status: 0 off > [ 499.407318] usb 2-1: USB disconnect, device number 2 > [ 499.424926] qcserial ttyUSB0: Qualcomm USB modem converter now > disconnected from ttyUSB0 > [ 499.434112] qcserial 2-1:1.0: device disconnected > [ 499.443389] qcserial ttyUSB1: Qualcomm USB modem converter now > disconnected from ttyUSB1 > [ 499.451904] qcserial 2-1:1.1: device disconnected > [ 499.460968] qcserial ttyUSB2: Qualcomm USB modem converter now > disconnected from ttyUSB2 > [ 499.469512] qcserial 2-1:1.2: device disconnected > [ 499.478057] qcserial ttyUSB3: Qualcomm USB modem converter now > disconnected from ttyUSB3 > [ 499.486572] qcserial 2-1:1.3: device disconnected > [ 499.504760] qcserial ttyUSB4: Qualcomm USB modem converter now > disconnected from ttyUSB4 > [ 499.513244] qcserial 2-1:1.4: device disconnected > [ 499.519104] qmi_wwan 2-1:1.5 wwan0: unregister 'qmi_wwan' > usb-4a064800.ohci-1, WWAN/QMI device > [ 499.611511] qmi_wwan 2-1:1.6 wwan1: unregister 'qmi_wwan' > usb-4a064800.ohci-1, WWAN/QMI device > [ 499.676086] Somebody do a proper driver please cpcap_soc_work > [ 499.688323] qmi_wwan 2-1:1.7 wwan2: unregister 'qmi_wwan' > usb-4a064800.ohci-1, WWAN/QMI device > [ 499.768859] qmi_wwan 2-1:1.8 wwan3: unregister 'qmi_wwan' > usb-4a064800.ohci-1, WWAN/QMI device > > That one will be fun to debug, I'm afraid. (Or does the message at > 495.496032 mean that we turned it off?) Looks like mdm6600 either entered low-power mode, or hung? If it hung, it's internal watchdog might bring it back after a while. If it entered low-power mode, in theory we should see the state change interrupt that's handled by phy-mapphone-mdm6600.c. I never managed to do that so far so maybe you figured it out with some command. Regards, Tony -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
