Quoting Karthikeyan Ramasubramanian (2018-03-14 16:58:50)
> diff --git a/arch/arm64/boot/dts/qcom/sdm845-mtp.dts b/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
> index 979ab49..ea3efc5 100644
> --- a/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
> +++ b/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
> @@ -12,4 +12,43 @@
> / {
> model = "Qualcomm Technologies, Inc. SDM845 MTP";
> compatible = "qcom,sdm845-mtp";
> +
> + aliases {
> + serial0 = &uart2;
> + };
> +
> + chosen {
> + stdout-path = "serial0";
Also add :115200n8 ?
> + };
> +};
> +
> +&soc {
I think the method is to put these inside soc node without using the
phandle reference. So indent everything once more.
> + geniqup@ac0000 {
> + serial@a84000 {
> + status = "okay";
> + };
> + };
> +
> + pinctrl@3400000 {
> + qup-uart2-default {
> + pinconf_tx {
> + pins = "gpio4";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + pinconf_rx {
> + pins = "gpio5";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> + };
> +
> + qup-uart2-sleep {
> + pinconf {
> + pins = "gpio4", "gpio5";
> + bias-pull-down;
> + };
> + };
> + };
> };
> diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
> index 32f8561..59334d9 100644
> --- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
> @@ -6,6 +6,7 @@
> */
>
> #include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/clock/qcom,gcc-sdm845.h>
>
> / {
> interrupt-parent = <&intc>;
> @@ -194,6 +195,20 @@
> #gpio-cells = <2>;
> interrupt-controller;
> #interrupt-cells = <2>;
> +
> + qup_uart2_default: qup-uart2-default {
> + pinmux {
> + function = "qup9";
> + pins = "gpio4", "gpio5";
> + };
> + };
> +
> + qup_uart2_sleep: qup-uart2-sleep {
> + pinmux {
> + function = "gpio";
> + pins = "gpio4", "gpio5";
> + };
> + };
Are these supposed to go to the board file?
> };
>
> timer@17c90000 {
> @@ -272,5 +287,28 @@
> #interrupt-cells = <4>;
> cell-index = <0>;
> };
> +
> + geniqup@ac0000 {
> + compatible = "qcom,geni-se-qup";
> + reg = <0xac0000 0x6000>;
> + clock-names = "m-ahb", "s-ahb";
> + clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
> + <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
Add a status = "disabled" here too.
> +
> + uart2: serial@a84000 {
> + compatible = "qcom,geni-debug-uart";
> + reg = <0xa84000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_uart2_default>;
> + pinctrl-1 = <&qup_uart2_sleep>;
> + interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
> + status = "disabled";
> + };
> + };
> };
> };
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
