Hi Doug,
Thanks for reviewing the patch.
On 3/16/2018 5:54 PM, Doug Anderson wrote:
> Hi,
>
> On Wed, Mar 14, 2018 at 4:58 PM, Karthikeyan Ramasubramanian
> <kramasub@xxxxxxxxxxxxxx> wrote:
>> Add I2C master controller support for a built-in test I2C slave.
>>
>> Signed-off-by: Karthikeyan Ramasubramanian <kramasub@xxxxxxxxxxxxxx>
>> ---
>> arch/arm64/boot/dts/qcom/sdm845-mtp.dts | 19 +++++++++++++++++++
>> arch/arm64/boot/dts/qcom/sdm845.dtsi | 29 +++++++++++++++++++++++++++++
>> 2 files changed, 48 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/sdm845-mtp.dts b/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
>> index ea3efc5..69445f1 100644
>> --- a/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
>> +++ b/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
>> @@ -27,6 +27,10 @@
>> serial@a84000 {
>> status = "okay";
>> };
>> +
>> + i2c@a88000 {
>> + status = "okay";
>
> Any idea what clock frequency is appropriate for MTP? You've got some
> pretty beefy 2.2K external pulls I think, so presumably 400 KHz is
> what you're aiming for? It would be nice to specify one so you don't
> end up the the spam in the log "Bus frequency not specified ..."
>
>
Yes, we plan to use 400Khz. We will specify it here.
>> + };
>> };
>>
>> pinctrl@3400000 {
>> @@ -50,5 +54,20 @@
>> bias-pull-down;
>> };
>> };
>> +
>> + qup-i2c10-default {
>
> nit: probably in the pinctrl section we want to sort alphabetically?
> We could try to sort by "lowest numbered pin", but IMHO alphabetical
> makes the most sense.
>
Sure.
>
>> + pinconf {
>> + pins = "gpio55", "gpio56";
>> + drive-strength = <2>;
>> + bias-disable;
>> + };
>> + };
>> +
>> + qup-i2c10-sleep {
>> + pinconf {
>> + pins = "gpio55", "gpio56";
>> + bias-pull-up;
>
> Are you sure that you want pullups enabled for sleep here? There are
> external pulls on this line (as there are on many i2c busses) so doing
> this will double-enable pulls. It probably won't hurt, but I'm
> curious if there's some sort of reason here.
>
1. We need the lines to remain high to avoid slaves sensing a false
start-condition (this can happen if the SDA goes down before SCL).
2. Disclaimer: I'm not a HW expert, but we were told that
tri-state/bias-disabled lines can draw more current. I will find out
more about that.
>
>> + };
>> + };
>> };
>> };
>> diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
>> index 59334d9..9ef056f 100644
>> --- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
>> @@ -209,6 +209,21 @@
>> pins = "gpio4", "gpio5";
>> };
>> };
>> +
>> + qup_i2c10_default: qup-i2c10-default {
>> + pinmux {
>> + function = "qup10";
>> + pins = "gpio55", "gpio56";
>> + };
>> + };
>> +
>> + qup_i2c10_sleep: qup-i2c10-sleep {
>> + pinmux {
>> + function = "gpio";
>> + pins = "gpio55", "gpio56";
>> + };
>> + };
>> +
>> };
>>
>> timer@17c90000 {
>> @@ -309,6 +324,20 @@
>> interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
>> status = "disabled";
>> };
>> +
>> + i2c10: i2c@a88000 {
>
> Seems like it might be nice to add all the i2c busses into the main
> sdm845.dtsi file. Sure, most won't be enabled, but it seems like it
> would avoid churn later.
>
> ...if you're sure you want to add only one i2c controller, subject of
> this patch should indicate that.
>
Yes, we typically have a "platform(sdm845 here)-qupv3.dtsi" defining
most of the serial-bus instances (i2c, spi, and uart with
status=disabled) that we include from the common header. The boards
enable instances they need.
Will that be okay?
Thanks
Sagar
>
>> + compatible = "qcom,geni-i2c";
>> + reg = <0xa88000 0x4000>;
>> + clock-names = "se";
>> + clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
>> + pinctrl-names = "default", "sleep";
>> + pinctrl-0 = <&qup_i2c10_default>;
>> + pinctrl-1 = <&qup_i2c10_sleep>;
>> + interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> };
>> };
>> };
>> --
>> Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
>> a Linux Foundation Collaborative Project
>>
>> --
>> To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
>> the body of a message to majordomo@xxxxxxxxxxxxxxx
>> More majordomo info at http://vger.kernel.org/majordomo-info.html
> --
> To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
--
Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
