Hi,
On Wed, Mar 14, 2018 at 4:58 PM, Karthikeyan Ramasubramanian
<kramasub@xxxxxxxxxxxxxx> wrote:
> Add I2C master controller support for a built-in test I2C slave.
>
> Signed-off-by: Karthikeyan Ramasubramanian <kramasub@xxxxxxxxxxxxxx>
> ---
> arch/arm64/boot/dts/qcom/sdm845-mtp.dts | 19 +++++++++++++++++++
> arch/arm64/boot/dts/qcom/sdm845.dtsi | 29 +++++++++++++++++++++++++++++
> 2 files changed, 48 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sdm845-mtp.dts b/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
> index ea3efc5..69445f1 100644
> --- a/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
> +++ b/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
> @@ -27,6 +27,10 @@
> serial@a84000 {
> status = "okay";
> };
> +
> + i2c@a88000 {
> + status = "okay";
Any idea what clock frequency is appropriate for MTP? You've got some
pretty beefy 2.2K external pulls I think, so presumably 400 KHz is
what you're aiming for? It would be nice to specify one so you don't
end up the the spam in the log "Bus frequency not specified ..."
> + };
> };
>
> pinctrl@3400000 {
> @@ -50,5 +54,20 @@
> bias-pull-down;
> };
> };
> +
> + qup-i2c10-default {
nit: probably in the pinctrl section we want to sort alphabetically?
We could try to sort by "lowest numbered pin", but IMHO alphabetical
makes the most sense.
> + pinconf {
> + pins = "gpio55", "gpio56";
> + drive-strength = <2>;
> + bias-disable;
> + };
> + };
> +
> + qup-i2c10-sleep {
> + pinconf {
> + pins = "gpio55", "gpio56";
> + bias-pull-up;
Are you sure that you want pullups enabled for sleep here? There are
external pulls on this line (as there are on many i2c busses) so doing
this will double-enable pulls. It probably won't hurt, but I'm
curious if there's some sort of reason here.
> + };
> + };
> };
> };
> diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
> index 59334d9..9ef056f 100644
> --- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
> @@ -209,6 +209,21 @@
> pins = "gpio4", "gpio5";
> };
> };
> +
> + qup_i2c10_default: qup-i2c10-default {
> + pinmux {
> + function = "qup10";
> + pins = "gpio55", "gpio56";
> + };
> + };
> +
> + qup_i2c10_sleep: qup-i2c10-sleep {
> + pinmux {
> + function = "gpio";
> + pins = "gpio55", "gpio56";
> + };
> + };
> +
> };
>
> timer@17c90000 {
> @@ -309,6 +324,20 @@
> interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
> status = "disabled";
> };
> +
> + i2c10: i2c@a88000 {
Seems like it might be nice to add all the i2c busses into the main
sdm845.dtsi file. Sure, most won't be enabled, but it seems like it
would avoid churn later.
...if you're sure you want to add only one i2c controller, subject of
this patch should indicate that.
> + compatible = "qcom,geni-i2c";
> + reg = <0xa88000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_i2c10_default>;
> + pinctrl-1 = <&qup_i2c10_sleep>;
> + interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> };
> };
> };
> --
> Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> a Linux Foundation Collaborative Project
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
