Hi Maxime,
Thanks for your patch,
I still need to find time to do a full review of this patch before I can
add my review tag to it. But in case you post a new version before I
find the time, the MODULE_LICENSE is still missing :-)
On 2018-03-14 14:16:02 +0100, Maxime Ripard wrote:
> The Cadence MIPI-CSI2 TX controller is an hardware block meant to be used
> as a bridge between pixel interfaces and a CSI-2 bus.
>
> It supports operating with an internal or external D-PHY, with up to 4
> lanes, or without any D-PHY. The current code only supports the latter
> case.
>
> While the virtual channel input on the pixel interface can be directly
> mapped to CSI2, the datatype input is actually a selection signal (3-bits)
> mapping to a table of up to 8 preconfigured datatypes/formats (programmed
> at start-up)
>
> The block supports up to 8 input datatypes.
>
> Signed-off-by: Maxime Ripard <maxime.ripard@xxxxxxxxxxx>
> ---
> drivers/media/platform/cadence/Kconfig | 11 +
> drivers/media/platform/cadence/Makefile | 1 +
> drivers/media/platform/cadence/cdns-csi2tx.c | 528 +++++++++++++++++++++++++++
> 3 files changed, 540 insertions(+)
> create mode 100644 drivers/media/platform/cadence/cdns-csi2tx.c
>
> diff --git a/drivers/media/platform/cadence/Kconfig b/drivers/media/platform/cadence/Kconfig
> index 18f061e5cbd1..83dcf2b1814b 100644
> --- a/drivers/media/platform/cadence/Kconfig
> +++ b/drivers/media/platform/cadence/Kconfig
> @@ -14,4 +14,15 @@ config VIDEO_CADENCE_CSI2RX
> To compile this driver as a module, choose M here: the module will be
> called cdns-csi2rx.
>
> +config VIDEO_CADENCE_CSI2TX
> + tristate "Cadence MIPI-CSI2 TX Controller"
> + depends on MEDIA_CONTROLLER
> + depends on VIDEO_V4L2_SUBDEV_API
> + select V4L2_FWNODE
> + help
> + Support for the Cadence MIPI CSI2 Transceiver controller.
> +
> + To compile this driver as a module, choose M here: the module will be
> + called cdns-csi2tx.
> +
> endif
> diff --git a/drivers/media/platform/cadence/Makefile b/drivers/media/platform/cadence/Makefile
> index 99a4086b7448..7fe992273162 100644
> --- a/drivers/media/platform/cadence/Makefile
> +++ b/drivers/media/platform/cadence/Makefile
> @@ -1 +1,2 @@
> obj-$(CONFIG_VIDEO_CADENCE_CSI2RX) += cdns-csi2rx.o
> +obj-$(CONFIG_VIDEO_CADENCE_CSI2TX) += cdns-csi2tx.o
> diff --git a/drivers/media/platform/cadence/cdns-csi2tx.c b/drivers/media/platform/cadence/cdns-csi2tx.c
> new file mode 100644
> index 000000000000..690ca7443569
> --- /dev/null
> +++ b/drivers/media/platform/cadence/cdns-csi2tx.c
> @@ -0,0 +1,528 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Driver for Cadence MIPI-CSI2 TX Controller
> + *
> + * Copyright (C) 2017 Cadence Design Systems Inc.
> + */
> +
> +#include <linux/atomic.h>
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/io.h>
> +#include <linux/module.h>
> +#include <linux/mutex.h>
> +#include <linux/of.h>
> +#include <linux/of_graph.h>
> +#include <linux/platform_device.h>
> +#include <linux/slab.h>
> +
> +#include <media/v4l2-ctrls.h>
> +#include <media/v4l2-device.h>
> +#include <media/v4l2-fwnode.h>
> +#include <media/v4l2-subdev.h>
> +
> +#define CSI2TX_DEVICE_CONFIG_REG 0x00
> +
> +#define CSI2TX_CONFIG_REG 0x20
> +#define CSI2TX_CONFIG_CFG_REQ BIT(2)
> +#define CSI2TX_CONFIG_SRST_REQ BIT(1)
> +
> +#define CSI2TX_DPHY_CFG_REG 0x28
> +#define CSI2TX_DPHY_CFG_CLK_RESET BIT(16)
> +#define CSI2TX_DPHY_CFG_LANE_RESET(n) BIT((n) + 12)
> +#define CSI2TX_DPHY_CFG_MODE_MASK GENMASK(9, 8)
> +#define CSI2TX_DPHY_CFG_MODE_LPDT (2 << 8)
> +#define CSI2TX_DPHY_CFG_MODE_HS (1 << 8)
> +#define CSI2TX_DPHY_CFG_MODE_ULPS (0 << 8)
> +#define CSI2TX_DPHY_CFG_CLK_ENABLE BIT(4)
> +#define CSI2TX_DPHY_CFG_LANE_ENABLE(n) BIT(n)
> +
> +#define CSI2TX_DPHY_CLK_WAKEUP_REG 0x2c
> +#define CSI2TX_DPHY_CLK_WAKEUP_ULPS_CYCLES(n) ((n) & 0xffff)
> +
> +#define CSI2TX_DT_CFG_REG(n) (0x80 + (n) * 8)
> +#define CSI2TX_DT_CFG_DT(n) (((n) & 0x3f) << 2)
> +
> +#define CSI2TX_DT_FORMAT_REG(n) (0x84 + (n) * 8)
> +#define CSI2TX_DT_FORMAT_BYTES_PER_LINE(n) (((n) & 0xffff) << 16)
> +#define CSI2TX_DT_FORMAT_MAX_LINE_NUM(n) ((n) & 0xffff)
> +
> +#define CSI2TX_STREAM_IF_CFG_REG(n) (0x100 + (n) * 4)
> +#define CSI2TX_STREAM_IF_CFG_FILL_LEVEL(n) ((n) & 0x1f)
> +
> +#define CSI2TX_LANES_MAX 4
> +#define CSI2TX_STREAMS_MAX 4
> +
> +enum csi2tx_pads {
> + CSI2TX_PAD_SOURCE,
> + CSI2TX_PAD_SINK_STREAM0,
> + CSI2TX_PAD_SINK_STREAM1,
> + CSI2TX_PAD_SINK_STREAM2,
> + CSI2TX_PAD_SINK_STREAM3,
> + CSI2TX_PAD_MAX,
> +};
> +
> +struct csi2tx_fmt {
> + u32 mbus;
> + u32 dt;
> + u32 bpp;
> +};
> +
> +struct csi2tx_priv {
> + struct device *dev;
> + unsigned int count;
> +
> + /*
> + * Used to prevent race conditions between multiple,
> + * concurrent calls to start and stop.
> + */
> + struct mutex lock;
> +
> + void __iomem *base;
> +
> + struct clk *esc_clk;
> + struct clk *p_clk;
> + struct clk *pixel_clk[CSI2TX_STREAMS_MAX];
> +
> + struct v4l2_subdev subdev;
> + struct media_pad pads[CSI2TX_PAD_MAX];
> + struct v4l2_mbus_framefmt pad_fmts[CSI2TX_PAD_MAX];
> +
> + bool has_internal_dphy;
> + u8 lanes[CSI2TX_LANES_MAX];
> + unsigned int num_lanes;
> + unsigned int max_lanes;
> + unsigned int max_streams;
> +};
> +
> +static const struct csi2tx_fmt csi2tx_formats[] = {
> + {
> + .mbus = MEDIA_BUS_FMT_UYVY8_1X16,
> + .bpp = 2,
> + .dt = 0x1e,
> + },
> + {
> + .mbus = MEDIA_BUS_FMT_RGB888_1X24,
> + .bpp = 3,
> + .dt = 0x24,
> + },
> +};
> +
> +static const struct v4l2_mbus_framefmt fmt_default = {
> + .width = 1280,
> + .height = 720,
> + .code = MEDIA_BUS_FMT_RGB888_1X24,
> + .field = V4L2_FIELD_NONE,
> + .colorspace = V4L2_COLORSPACE_DEFAULT,
> +};
> +
> +static inline
> +struct csi2tx_priv *v4l2_subdev_to_csi2tx(struct v4l2_subdev *subdev)
> +{
> + return container_of(subdev, struct csi2tx_priv, subdev);
> +}
> +
> +static const struct csi2tx_fmt *csitx_get_fmt_from_mbus(struct v4l2_mbus_framefmt *mfmt)
> +{
> + unsigned int i;
> +
> + if (!mfmt)
> + return NULL;
> +
> + for (i = 0; i < ARRAY_SIZE(csi2tx_formats); i++)
> + if (csi2tx_formats[i].mbus == mfmt->code)
> + return &csi2tx_formats[i];
> +
> + return NULL;
> +}
> +
> +static int csi2tx_enum_mbus_code(struct v4l2_subdev *subdev,
> + struct v4l2_subdev_pad_config *cfg,
> + struct v4l2_subdev_mbus_code_enum *code)
> +{
> + if (code->pad || code->index >= ARRAY_SIZE(csi2tx_formats))
> + return -EINVAL;
> +
> + code->code = csi2tx_formats[code->index].mbus;
> +
> + return 0;
> +}
> +
> +static int csi2tx_get_pad_format(struct v4l2_subdev *subdev,
> + struct v4l2_subdev_pad_config *cfg,
> + struct v4l2_subdev_format *fmt)
> +{
> + struct csi2tx_priv *csi2tx = v4l2_subdev_to_csi2tx(subdev);
> +
> + if (fmt->pad >= CSI2TX_PAD_MAX)
> + return -EINVAL;
> +
> + fmt->format = csi2tx->pad_fmts[fmt->pad];
> +
> + return 0;
> +}
> +
> +static int csi2tx_set_pad_format(struct v4l2_subdev *subdev,
> + struct v4l2_subdev_pad_config *cfg,
> + struct v4l2_subdev_format *fmt)
> +{
> + struct csi2tx_priv *csi2tx = v4l2_subdev_to_csi2tx(subdev);
> +
> + if (fmt->pad >= CSI2TX_PAD_MAX)
> + return -EINVAL;
> +
> + csi2tx->pad_fmts[fmt->pad] = fmt->format;
> +
> + return 0;
> +}
> +
> +static const struct v4l2_subdev_pad_ops csi2tx_pad_ops = {
> + .enum_mbus_code = csi2tx_enum_mbus_code,
> + .get_fmt = csi2tx_get_pad_format,
> + .set_fmt = csi2tx_set_pad_format,
> +};
> +
> +static void csi2tx_reset(struct csi2tx_priv *csi2tx)
> +{
> + writel(CSI2TX_CONFIG_SRST_REQ, csi2tx->base + CSI2TX_CONFIG_REG);
> +
> + udelay(10);
> +}
> +
> +static int csi2tx_start(struct csi2tx_priv *csi2tx)
> +{
> + struct media_entity *entity = &csi2tx->subdev.entity;
> + struct media_link *link;
> + unsigned int i;
> + u32 reg;
> +
> + csi2tx_reset(csi2tx);
> +
> + writel(CSI2TX_CONFIG_CFG_REQ, csi2tx->base + CSI2TX_CONFIG_REG);
> +
> + udelay(10);
> +
> + /* Configure our PPI interface with the D-PHY */
> + writel(CSI2TX_DPHY_CLK_WAKEUP_ULPS_CYCLES(32),
> + csi2tx->base + CSI2TX_DPHY_CLK_WAKEUP_REG);
> +
> + /* Put our lanes (clock and data) out of reset */
> + reg = CSI2TX_DPHY_CFG_CLK_RESET | CSI2TX_DPHY_CFG_MODE_LPDT;
> + for (i = 0; i < csi2tx->num_lanes; i++)
> + reg |= CSI2TX_DPHY_CFG_LANE_RESET(csi2tx->lanes[i]);
> + writel(reg, csi2tx->base + CSI2TX_DPHY_CFG_REG);
> +
> + udelay(10);
> +
> + /* Enable our (clock and data) lanes */
> + reg |= CSI2TX_DPHY_CFG_CLK_ENABLE;
> + for (i = 0; i < csi2tx->num_lanes; i++)
> + reg |= CSI2TX_DPHY_CFG_LANE_ENABLE(csi2tx->lanes[i]);
> + writel(reg, csi2tx->base + CSI2TX_DPHY_CFG_REG);
> +
> + udelay(10);
> +
> + /* Switch to HS mode */
> + reg &= ~CSI2TX_DPHY_CFG_MODE_MASK;
> + writel(reg | CSI2TX_DPHY_CFG_MODE_HS,
> + csi2tx->base + CSI2TX_DPHY_CFG_REG);
> +
> + udelay(10);
> +
> + /*
> + * Create a static mapping between the CSI virtual channels
> + * and the input streams.
> + *
> + * This should be enhanced, but v4l2 lacks the support for
> + * changing that mapping dynamically at the moment.
> + *
> + * We're protected from the userspace setting up links at the
> + * same time by the upper layer having called
> + * media_pipeline_start().
> + */
> + list_for_each_entry(link, &entity->links, list) {
> + struct v4l2_mbus_framefmt *mfmt;
> + const struct csi2tx_fmt *fmt;
> + unsigned int stream;
> + int pad_idx = -1;
> +
> + /* Only consider our enabled input pads */
> + for (i = CSI2TX_PAD_SINK_STREAM0; i < CSI2TX_PAD_MAX; i++) {
> + struct media_pad *pad = &csi2tx->pads[i];
> +
> + if ((pad == link->sink) &&
> + (link->flags & MEDIA_LNK_FL_ENABLED)) {
> + pad_idx = i;
> + break;
> + }
> + }
> +
> + if (pad_idx < 0)
> + continue;
> +
> + mfmt = &csi2tx->pad_fmts[i];
> + fmt = csitx_get_fmt_from_mbus(mfmt);
> + if (!fmt)
> + continue;
> +
> + stream = pad_idx - CSI2TX_PAD_SINK_STREAM0;
> +
> + /*
> + * We use the stream ID there, but it's wrong.
> + *
> + * A stream could very well send a data type that is
> + * not equal to its stream ID. We need to find a
> + * proper way to address it.
> + */
> + writel(CSI2TX_DT_CFG_DT(fmt->dt),
> + csi2tx->base + CSI2TX_DT_CFG_REG(stream));
> +
> + writel(CSI2TX_DT_FORMAT_BYTES_PER_LINE(mfmt->width * fmt->bpp) |
> + CSI2TX_DT_FORMAT_MAX_LINE_NUM(mfmt->height + 1),
> + csi2tx->base + CSI2TX_DT_FORMAT_REG(stream));
> +
> + /*
> + * TODO: This needs to be calculated based on the
> + * output CSI2 clock rate.
> + */
> + writel(CSI2TX_STREAM_IF_CFG_FILL_LEVEL(4),
> + csi2tx->base + CSI2TX_STREAM_IF_CFG_REG(stream));
> + }
> +
> + /* Disable the configuration mode */
> + writel(0, csi2tx->base + CSI2TX_CONFIG_REG);
> +
> + return 0;
> +}
> +
> +static void csi2tx_stop(struct csi2tx_priv *csi2tx)
> +{
> + writel(CSI2TX_CONFIG_CFG_REQ | CSI2TX_CONFIG_SRST_REQ,
> + csi2tx->base + CSI2TX_CONFIG_REG);
> +}
> +
> +static int csi2tx_s_stream(struct v4l2_subdev *subdev, int enable)
> +{
> + struct csi2tx_priv *csi2tx = v4l2_subdev_to_csi2tx(subdev);
> + int ret = 0;
> +
> + mutex_lock(&csi2tx->lock);
> +
> + if (enable) {
> + /*
> + * If we're not the first users, there's no need to
> + * enable the whole controller.
> + */
> + if (!csi2tx->count) {
> + ret = csi2tx_start(csi2tx);
> + if (ret)
> + goto out;
> + }
> +
> + csi2tx->count++;
> + } else {
> + csi2tx->count--;
> +
> + /*
> + * Let the last user turn off the lights.
> + */
> + if (!csi2tx->count)
> + csi2tx_stop(csi2tx);
> + }
> +
> +out:
> + mutex_unlock(&csi2tx->lock);
> + return ret;
> +}
> +
> +static const struct v4l2_subdev_video_ops csi2tx_video_ops = {
> + .s_stream = csi2tx_s_stream,
> +};
> +
> +static const struct v4l2_subdev_ops csi2tx_subdev_ops = {
> + .pad = &csi2tx_pad_ops,
> + .video = &csi2tx_video_ops,
> +};
> +
> +static int csi2tx_get_resources(struct csi2tx_priv *csi2tx,
> + struct platform_device *pdev)
> +{
> + struct resource *res;
> + unsigned int i;
> + u32 dev_cfg;
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + csi2tx->base = devm_ioremap_resource(&pdev->dev, res);
> + if (IS_ERR(csi2tx->base))
> + return PTR_ERR(csi2tx->base);
> +
> + csi2tx->p_clk = devm_clk_get(&pdev->dev, "p_clk");
> + if (IS_ERR(csi2tx->p_clk)) {
> + dev_err(&pdev->dev, "Couldn't get p_clk\n");
> + return PTR_ERR(csi2tx->p_clk);
> + }
> +
> + csi2tx->esc_clk = devm_clk_get(&pdev->dev, "esc_clk");
> + if (IS_ERR(csi2tx->esc_clk)) {
> + dev_err(&pdev->dev, "Couldn't get the esc_clk\n");
> + return PTR_ERR(csi2tx->esc_clk);
> + }
> +
> + clk_prepare_enable(csi2tx->p_clk);
> + dev_cfg = readl(csi2tx->base + CSI2TX_DEVICE_CONFIG_REG);
> + clk_disable_unprepare(csi2tx->p_clk);
> +
> + csi2tx->max_lanes = dev_cfg & 7;
> + if (csi2tx->max_lanes > CSI2TX_LANES_MAX) {
> + dev_err(&pdev->dev, "Invalid number of lanes: %u\n",
> + csi2tx->max_lanes);
> + return -EINVAL;
> + }
> +
> + csi2tx->max_streams = (dev_cfg >> 4) & 7;
> + if (csi2tx->max_streams > CSI2TX_STREAMS_MAX) {
> + dev_err(&pdev->dev, "Invalid number of streams: %u\n",
> + csi2tx->max_streams);
> + return -EINVAL;
> + }
> +
> + csi2tx->has_internal_dphy = (dev_cfg & BIT(3)) ? true : false;
> +
> + for (i = 0; i < csi2tx->max_streams; i++) {
> + char clk_name[16];
> +
> + snprintf(clk_name, sizeof(clk_name), "pixel_if%u_clk", i);
> + csi2tx->pixel_clk[i] = devm_clk_get(&pdev->dev, clk_name);
> + if (IS_ERR(csi2tx->pixel_clk[i])) {
> + dev_err(&pdev->dev, "Couldn't get clock %s\n",
> + clk_name);
> + return PTR_ERR(csi2tx->pixel_clk[i]);
> + }
> + }
> +
> + return 0;
> +}
> +
> +static int csi2tx_check_lanes(struct csi2tx_priv *csi2tx)
> +{
> + struct v4l2_fwnode_endpoint v4l2_ep;
> + struct device_node *ep;
> + int ret;
> +
> + ep = of_graph_get_endpoint_by_regs(csi2tx->dev->of_node, 0, 0);
> + if (!ep)
> + return -EINVAL;
> +
> + ret = v4l2_fwnode_endpoint_parse(of_fwnode_handle(ep), &v4l2_ep);
> + if (ret) {
> + dev_err(csi2tx->dev, "Could not parse v4l2 endpoint\n");
> + goto out;
> + }
> +
> + if (v4l2_ep.bus_type != V4L2_MBUS_CSI2) {
> + dev_err(csi2tx->dev, "Unsupported media bus type: 0x%x\n",
> + v4l2_ep.bus_type);
> + ret = -EINVAL;
> + goto out;
> + }
> +
> + csi2tx->num_lanes = v4l2_ep.bus.mipi_csi2.num_data_lanes;
> + if (csi2tx->num_lanes > csi2tx->max_lanes) {
> + dev_err(csi2tx->dev,
> + "Current configuration uses more lanes than supported\n");
> + ret = -EINVAL;
> + goto out;
> + }
> +
> + memcpy(csi2tx->lanes, v4l2_ep.bus.mipi_csi2.data_lanes,
> + sizeof(csi2tx->lanes));
> +
> +out:
> + of_node_put(ep);
> + return ret;
> +}
> +
> +static int csi2tx_probe(struct platform_device *pdev)
> +{
> + struct csi2tx_priv *csi2tx;
> + unsigned int i;
> + int ret;
> +
> + csi2tx = kzalloc(sizeof(*csi2tx), GFP_KERNEL);
> + if (!csi2tx)
> + return -ENOMEM;
> + platform_set_drvdata(pdev, csi2tx);
> + mutex_init(&csi2tx->lock);
> + csi2tx->dev = &pdev->dev;
> +
> + ret = csi2tx_get_resources(csi2tx, pdev);
> + if (ret)
> + goto err_free_priv;
> +
> + v4l2_subdev_init(&csi2tx->subdev, &csi2tx_subdev_ops);
> + csi2tx->subdev.owner = THIS_MODULE;
> + csi2tx->subdev.dev = &pdev->dev;
> + csi2tx->subdev.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
> + snprintf(csi2tx->subdev.name, V4L2_SUBDEV_NAME_SIZE, "%s.%s",
> + KBUILD_MODNAME, dev_name(&pdev->dev));
> +
> + ret = csi2tx_check_lanes(csi2tx);
> + if (ret)
> + goto err_free_priv;
> +
> + /* Create our media pads */
> + csi2tx->subdev.entity.function = MEDIA_ENT_F_VID_IF_BRIDGE;
> + csi2tx->pads[CSI2TX_PAD_SOURCE].flags = MEDIA_PAD_FL_SOURCE;
> + for (i = CSI2TX_PAD_SINK_STREAM0; i < CSI2TX_PAD_MAX; i++)
> + csi2tx->pads[i].flags = MEDIA_PAD_FL_SINK;
> +
> + for (i = 0; i < CSI2TX_PAD_MAX; i++)
> + csi2tx->pad_fmts[i] = fmt_default;
> +
> + ret = media_entity_pads_init(&csi2tx->subdev.entity, CSI2TX_PAD_MAX,
> + csi2tx->pads);
> + if (ret)
> + goto err_free_priv;
> +
> + ret = v4l2_async_register_subdev(&csi2tx->subdev);
> + if (ret < 0)
> + goto err_free_priv;
> +
> + dev_info(&pdev->dev,
> + "Probed CSI2TX with %u/%u lanes, %u streams, %s D-PHY\n",
> + csi2tx->num_lanes, csi2tx->max_lanes, csi2tx->max_streams,
> + csi2tx->has_internal_dphy ? "internal" : "no");
> +
> + return 0;
> +
> +err_free_priv:
> + kfree(csi2tx);
> + return ret;
> +}
> +
> +static int csi2tx_remove(struct platform_device *pdev)
> +{
> + struct csi2tx_priv *csi2tx = platform_get_drvdata(pdev);
> +
> + v4l2_async_unregister_subdev(&csi2tx->subdev);
> + kfree(csi2tx);
> +
> + return 0;
> +}
> +
> +static const struct of_device_id csi2tx_of_table[] = {
> + { .compatible = "cdns,csi2tx" },
> + { },
> +};
> +MODULE_DEVICE_TABLE(of, csi2tx_of_table);
> +
> +static struct platform_driver csi2tx_driver = {
> + .probe = csi2tx_probe,
> + .remove = csi2tx_remove,
> +
> + .driver = {
> + .name = "cdns-csi2tx",
> + .of_match_table = csi2tx_of_table,
> + },
> +};
> +module_platform_driver(csi2tx_driver);
> --
> 2.14.3
>
--
Regards,
Niklas Söderlund
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
