Got two email addresses wrong.
On 16/02/14 20:27, klightspeed@xxxxxxxxxxxxxxxx wrote:
> Add device tree fragments and files to support many of the kirkwood
> based Synology NAS devices. This is a modification of
> Andrew Lunn's <andrew@xxxxxxx> translation of the board setup file
> maintained by Ben Peddell <klightspeed@xxxxxxxxxxxxxxxx>
>
> The Ricoh RS5C372 RTC was used in all 2009 units and some 2010 units.
> All other Synology Kirkwood-based DiskStations and RackStations use
> the Seiko S35390A RTC.
>
> Most of the 1-bay and 2-bay units use the GPIOs that are multiplexed
> with the built-in SATA interface activity/presence pins on mpp 20-23,
> while the 4-bay units use ge01 and a PCIe SATA controller, and put the
> software controlled HDD leds on mpp 36-43.
>
> Most of the 6281 units with HDD power controls use mpp 29 and 31, while
> most of the 6282 units with HDD power controls use mpp 30, 34, 44 and 45
> and provide a model ID on mpp 28, 29, 46 and 47. Pre-2012 units and
> most 4-bay units didn't have a separate power control for HDD1. These
> power controls are presumably to limit startup current from the 12V brick
> power supply.
>
> Instead of using separate dtsi files in a synology directory, this
> patch uses a single dtsi file containing all of the modules for
> these boards, with all of the modules not common to all boards
> disabled. The board dts files then enable the appropriate modules for
> their boards.
>
> Signed-off-by: Ben Peddell <klightspeed@xxxxxxxxxxxxxxxx>
> Tested-by: Ben Peddell <klightspeed@xxxxxxxxxxxxxxxx> (ds211j)
> ---
> arch/arm/boot/dts/Makefile | 15 +
> arch/arm/boot/dts/kirkwood-ds-rs-common.dtsi | 764 +++++++++++++++++++++++++++
> arch/arm/boot/dts/kirkwood-ds109.dts | 42 ++
> arch/arm/boot/dts/kirkwood-ds110jv10.dts | 41 ++
> arch/arm/boot/dts/kirkwood-ds111.dts | 44 ++
> arch/arm/boot/dts/kirkwood-ds112.dts | 48 ++
> arch/arm/boot/dts/kirkwood-ds209.dts | 44 ++
> arch/arm/boot/dts/kirkwood-ds210.dts | 46 ++
> arch/arm/boot/dts/kirkwood-ds212.dts | 47 ++
> arch/arm/boot/dts/kirkwood-ds212j.dts | 41 ++
> arch/arm/boot/dts/kirkwood-ds409.dts | 48 ++
> arch/arm/boot/dts/kirkwood-ds409slim.dts | 40 ++
> arch/arm/boot/dts/kirkwood-ds411.dts | 52 ++
> arch/arm/boot/dts/kirkwood-ds411j.dts | 48 ++
> arch/arm/boot/dts/kirkwood-ds411slim.dts | 48 ++
> arch/arm/boot/dts/kirkwood-rs212.dts | 48 ++
> arch/arm/boot/dts/kirkwood-rs409.dts | 44 ++
> arch/arm/boot/dts/kirkwood-rs411.dts | 44 ++
> 18 files changed, 1503 insertions(+)
> create mode 100644 arch/arm/boot/dts/kirkwood-ds-rs-common.dtsi
> create mode 100644 arch/arm/boot/dts/kirkwood-ds109.dts
> create mode 100644 arch/arm/boot/dts/kirkwood-ds110jv10.dts
> create mode 100644 arch/arm/boot/dts/kirkwood-ds111.dts
> create mode 100644 arch/arm/boot/dts/kirkwood-ds112.dts
> create mode 100644 arch/arm/boot/dts/kirkwood-ds209.dts
> create mode 100644 arch/arm/boot/dts/kirkwood-ds210.dts
> create mode 100644 arch/arm/boot/dts/kirkwood-ds212.dts
> create mode 100644 arch/arm/boot/dts/kirkwood-ds212j.dts
> create mode 100644 arch/arm/boot/dts/kirkwood-ds409.dts
> create mode 100644 arch/arm/boot/dts/kirkwood-ds409slim.dts
> create mode 100644 arch/arm/boot/dts/kirkwood-ds411.dts
> create mode 100644 arch/arm/boot/dts/kirkwood-ds411j.dts
> create mode 100644 arch/arm/boot/dts/kirkwood-ds411slim.dts
> create mode 100644 arch/arm/boot/dts/kirkwood-rs212.dts
> create mode 100644 arch/arm/boot/dts/kirkwood-rs409.dts
> create mode 100644 arch/arm/boot/dts/kirkwood-rs411.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index b9d6a8b..6cf3a54 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -89,6 +89,18 @@ dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-cloudbox.dtb \
> kirkwood-dns325.dtb \
> kirkwood-dockstar.dtb \
> kirkwood-dreamplug.dtb \
> + kirkwood-ds109.dtb \
> + kirkwood-ds110jv10.dtb \
> + kirkwood-ds111.dtb \
> + kirkwood-ds209.dtb \
> + kirkwood-ds210.dtb \
> + kirkwood-ds212.dtb \
> + kirkwood-ds212j.dtb \
> + kirkwood-ds409.dtb \
> + kirkwood-ds409slim.dtb \
> + kirkwood-ds411.dtb \
> + kirkwood-ds411j.dtb \
> + kirkwood-ds411slim.dtb \
> kirkwood-goflexnet.dtb \
> kirkwood-guruplug-server-plus.dtb \
> kirkwood-ib62x0.dtb \
> @@ -111,6 +123,9 @@ dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-cloudbox.dtb \
> kirkwood-nsa310a.dtb \
> kirkwood-openblocks_a6.dtb \
> kirkwood-openblocks_a7.dtb \
> + kirkwood-rs212.dtb \
> + kirkwood-rs409.dtb \
> + kirkwood-rs411.dtb \
> kirkwood-sheevaplug.dtb \
> kirkwood-sheevaplug-esata.dtb \
> kirkwood-topkick.dtb \
> diff --git a/arch/arm/boot/dts/kirkwood-ds-rs-common.dtsi b/arch/arm/boot/dts/kirkwood-ds-rs-common.dtsi
> new file mode 100644
> index 0000000..65f0b9d
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-ds-rs-common.dtsi
> @@ -0,0 +1,764 @@
> +/*
> + * Nodes for Marvell 628x Synology devices
> + *
> + * Andrew Lunn <andrew@xxxxxxx>
> + * Ben Peddell <klightspeed@xxxxxxxxxxxxxxxx>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +
> +/ {
> + mbus {
> + pcie-controller {
> + status = "okay";
> +
> + pcie@1,0 {
> + status = "okay";
> + };
> + pcie2: pcie@2,0 {
> + status = "disabled";
> + };
> + };
> + };
> + ocp@f1000000 {
> + pinctrl: pinctrl@10000 {
> + pmx_alarmled_12: pmx-alarmled-12 {
> + marvell,pins = "mpp12";
> + marvell,function = "gpio";
> + };
> + pmx_fanctrl_15: pmx-fanctrl-15 {
> + marvell,pins = "mpp15";
> + marvell,function = "gpio";
> + };
> + pmx_fanctrl_16: pmx-fanctrl-16 {
> + marvell,pins = "mpp16";
> + marvell,function = "gpio";
> + };
> + pmx_fanctrl_17: pmx-fanctrl-17 {
> + marvell,pins = "mpp17";
> + marvell,function = "gpio";
> + };
> + pmx_fanalarm_18: pmx-fanalarm-18 {
> + marvell,pins = "mpp18";
> + marvell,function = "gpo";
> + };
> + pmx_hddled_20: pmx-hddled-20 {
> + marvell,pins = "mpp20";
> + marvell,function = "gpio";
> + };
> + pmx_hddled_21: pmx-hddled-21 {
> + marvell,pins = "mpp21";
> + marvell,function = "gpio";
> + };
> + pmx_hddled_22: pmx-hddled-22 {
> + marvell,pins = "mpp22";
> + marvell,function = "gpio";
> + };
> + pmx_hddled_23: pmx-hddled-23 {
> + marvell,pins = "mpp23";
> + marvell,function = "gpio";
> + };
> + pmx_hddled_24: pmx-hddled-24 {
> + marvell,pins = "mpp24";
> + marvell,function = "gpio";
> + };
> + pmx_hddled_25: pmx-hddled-25 {
> + marvell,pins = "mpp25";
> + marvell,function = "gpio";
> + };
> + pmx_hddled_26: pmx-hddled-26 {
> + marvell,pins = "mpp26";
> + marvell,function = "gpio";
> + };
> + pmx_hddled_27: pmx-hddled-27 {
> + marvell,pins = "mpp27";
> + marvell,function = "gpio";
> + };
> + pmx_hddled_28: pmx-hddled-28 {
> + marvell,pins = "mpp28";
> + marvell,function = "gpio";
> + };
> + pmx_hdd1_pwr_29: pmx-hdd1-pwr-29 {
> + marvell,pins = "mpp29";
> + marvell,function = "gpio";
> + };
> + pmx_hdd1_pwr_30: pmx-hdd-pwr-30 {
> + marvell,pins = "mpp30";
> + marvell,function = "gpio";
> + };
> + pmx_hdd2_pwr_31: pmx-hdd2-pwr-31 {
> + marvell,pins = "mpp31";
> + marvell,function = "gpio";
> + };
> + pmx_fanctrl_32: pmx-fanctrl-32 {
> + marvell,pins = "mpp32";
> + marvell,function = "gpio";
> + };
> + pmx_fanctrl_33: pmx-fanctrl-33 {
> + marvell,pins = "mpp33";
> + marvell,function = "gpo";
> + };
> + pmx_fanctrl_34: pmx-fanctrl-34 {
> + marvell,pins = "mpp34";
> + marvell,function = "gpio";
> + };
> + pmx_hdd2_pwr_34: pmx-hdd2-pwr-34 {
> + marvell,pins = "mpp34";
> + marvell,function = "gpio";
> + };
> + pmx_fanalarm_35: pmx-fanalarm-35 {
> + marvell,pins = "mpp35";
> + marvell,function = "gpio";
> + };
> + pmx_hddled_36: pmx-hddled-36 {
> + marvell,pins = "mpp36";
> + marvell,function = "gpio";
> + };
> + pmx_hddled_37: pmx-hddled-37 {
> + marvell,pins = "mpp37";
> + marvell,function = "gpio";
> + };
> + pmx_hddled_38: pmx-hddled-38 {
> + marvell,pins = "mpp38";
> + marvell,function = "gpio";
> + };
> + pmx_hddled_39: pmx-hddled-39 {
> + marvell,pins = "mpp39";
> + marvell,function = "gpio";
> + };
> + pmx_hddled_40: pmx-hddled-40 {
> + marvell,pins = "mpp40";
> + marvell,function = "gpio";
> + };
> + pmx_hddled_41: pmx-hddled-41 {
> + marvell,pins = "mpp41";
> + marvell,function = "gpio";
> + };
> + pmx_hddled_42: pmx-hddled-42 {
> + marvell,pins = "mpp42";
> + marvell,function = "gpio";
> + };
> + pmx_hddled_43: pmx-hddled-43 {
> + marvell,pins = "mpp43";
> + marvell,function = "gpio";
> + };
> + pmx_hddled_44: pmx-hddled-44 {
> + marvell,pins = "mpp44";
> + marvell,function = "gpio";
> + };
> + pmx_hddled_45: pmx-hddled-45 {
> + marvell,pins = "mpp45";
> + marvell,function = "gpio";
> + };
> + pmx_hdd3_pwr_44: pmx-hdd3-pwr-44 {
> + marvell,pins = "mpp44";
> + marvell,function = "gpio";
> + };
> + pmx_hdd4_pwr_45: pmx-hdd4-pwr-45 {
> + marvell,pins = "mpp45";
> + marvell,function = "gpio";
> + };
> + pmx_fanalarm_44: pmx-fanalarm-44 {
> + marvell,pins = "mpp44";
> + marvell,function = "gpio";
> + };
> + pmx_fanalarm_45: pmx-fanalarm-45 {
> + marvell,pins = "mpp45";
> + marvell,function = "gpio";
> + };
> + };
> + i2c@11000 {
> + status = "okay";
> + clock-frequency = <400000>;
> + pinctrl-0 = <&pmx_twsi0>;
> + pinctrl-names = "default";
> + rs5c372: rs5c372@32 {
> + status = "disabled";
> + compatible = "rs5c372";
> + reg = <0x32>;
> + };
> + s35390a: s35390a@30 {
> + status = "disabled";
> + compatible = "s35390a";
> + reg = <0x30>;
> + };
> + };
> + serial@12000 {
> + status = "okay";
> + pinctrl-0 = <&pmx_uart0>;
> + pinctrl-names = "default";
> + };
> + serial@12100 {
> + status = "okay";
> + pinctrl-0 = <&pmx_uart1>;
> + pinctrl-names = "default";
> + };
> + poweroff@12100 {
> + compatible = "synology,power-off";
> + reg = <0x12000 0x100>;
> + clocks = <&gate_clk 7>;
> + };
> + spi@10600 {
> + status = "okay";
> + pinctrl-0 = <&pmx_spi>;
> + pinctrl-names = "default";
> +
> + m25p80@0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "m25p80";
> + reg = <0>;
> + spi-max-frequency = <20000000>;
> + mode = <0>;
> +
> + partition@00000000 {
> + reg = <0x00000000 0x00080000>;
> + label = "RedBoot";
> + };
> +
> + partition@00080000 {
> + reg = <0x00080000 0x00200000>;
> + label = "zImage";
> + };
> +
> + partition@00280000 {
> + reg = <0x00280000 0x00140000>;
> + label = "rd.gz";
> + };
> + partition@003c0000 {
> + reg = <0x003c0000 0x00010000>;
> + label = "vendor";
> + };
> + partition@003d0000 {
> + reg = <0x003d0000 0x00020000>;
> + label = "RedBoot config";
> + };
> + partition@003f0000 {
> + reg = <0x003f0000 0x00010000>;
> + label = "FIS directory";
> + };
> + };
> + };
> + sata@80000 {
> + pinctrl-0 = <&pmx_sata0 &pmx_sata1>;
> + pinctrl-names = "default";
> + status = "okay";
> + nr-ports = <2>;
> + };
> + };
> + gpio-fan-150-32-35 {
> + status = "disabled";
> + compatible = "gpio-fan";
> + pinctrl-0 = <&pmx_fanctrl_32 &pmx_fanctrl_33 &pmx_fanctrl_34
> + &pmx_fanalarm_35>;
> + pinctrl-names = "default";
> + gpios = <&gpio1 0 GPIO_ACTIVE_HIGH
> + &gpio1 1 GPIO_ACTIVE_HIGH
> + &gpio1 2 GPIO_ACTIVE_HIGH>;
> + gpio-fan,speed-map = < 0 0
> + 2200 1
> + 2500 2
> + 3000 4
> + 3300 3
> + 3700 5
> + 3800 6
> + 4200 7 >;
> + };
> + gpio-fan-150-15-18 {
> + status = "disabled";
> + compatible = "gpio-fan";
> + pinctrl-0 = <&pmx_fanctrl_15 &pmx_fanctrl_16 &pmx_fanctrl_17
> + &pmx_fanalarm_18>;
> + pinctrl-names = "default";
> + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH
> + &gpio0 16 GPIO_ACTIVE_HIGH
> + &gpio0 17 GPIO_ACTIVE_HIGH>;
> + alarm-gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>;
> + gpio-fan,speed-map = < 0 0
> + 2200 1
> + 2500 2
> + 3000 4
> + 3300 3
> + 3700 5
> + 3800 6
> + 4200 7 >;
> + };
> + gpio-fan-100-32-35 {
> + status = "disabled";
> + compatible = "gpio-fan";
> + pinctrl-0 = <&pmx_fanctrl_32 &pmx_fanctrl_33 &pmx_fanctrl_34
> + &pmx_fanalarm_35>;
> + pinctrl-names = "default";
> + gpios = <&gpio1 0 GPIO_ACTIVE_HIGH
> + &gpio1 1 GPIO_ACTIVE_HIGH
> + &gpio1 2 GPIO_ACTIVE_HIGH>;
> + alarm-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
> + gpio-fan,speed-map = < 0 0
> + 2500 1
> + 3100 2
> + 3800 3
> + 4600 4
> + 4800 5
> + 4900 6
> + 5000 7 >;
> + };
> + gpio-fan-100-15-18 {
> + status = "disabled";
> + compatible = "gpio-fan";
> + pinctrl-0 = <&pmx_fanctrl_15 &pmx_fanctrl_16 &pmx_fanctrl_17
> + &pmx_fanalarm_18>;
> + pinctrl-names = "default";
> + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH
> + &gpio0 16 GPIO_ACTIVE_HIGH
> + &gpio0 17 GPIO_ACTIVE_HIGH>;
> + alarm-gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>;
> + gpio-fan,speed-map = < 0 0
> + 2500 1
> + 3100 2
> + 3800 3
> + 4600 4
> + 4800 5
> + 4900 6
> + 5000 7 >;
> + };
> + gpio-fan-100-15-35-1 {
> + status = "disabled";
> + compatible = "gpio-fan";
> + pinctrl-0 = <&pmx_fanctrl_15 &pmx_fanctrl_16 &pmx_fanctrl_17
> + &pmx_fanalarm_35>;
> + pinctrl-names = "default";
> + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH
> + &gpio0 16 GPIO_ACTIVE_HIGH
> + &gpio0 17 GPIO_ACTIVE_HIGH>;
> + alarm-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
> + gpio-fan,speed-map = < 0 0
> + 2500 1
> + 3100 2
> + 3800 3
> + 4600 4
> + 4800 5
> + 4900 6
> + 5000 7 >;
> + };
> + gpio-fan-100-15-35-3 {
> + status = "disabled";
> + compatible = "gpio-fan";
> + pinctrl-0 = <&pmx_fanctrl_15 &pmx_fanctrl_16 &pmx_fanctrl_17
> + &pmx_fanalarm_35 &pmx_fanalarm_44 &pmx_fanalarm_45>;
> + pinctrl-names = "default";
> + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH
> + &gpio0 16 GPIO_ACTIVE_HIGH
> + &gpio0 17 GPIO_ACTIVE_HIGH>;
> + alarm-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH
> + &gpio1 12 GPIO_ACTIVE_HIGH
> + &gpio1 13 GPIO_ACTIVE_HIGH>;
> + gpio-fan,speed-map = < 0 0
> + 2500 1
> + 3100 2
> + 3800 3
> + 4600 4
> + 4800 5
> + 4900 6
> + 5000 7 >;
> + };
> + gpio-leds-alarm-12 {
> + status = "disabled";
> + compatible = "gpio-leds";
> + pinctrl-0 = <&pmx_alarmled_12>;
> + pinctrl-names = "default";
> + hdd1-green {
> + label = "synology:alarm";
> + gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
> + };
> + };
> + gpio-leds-hdd-20 {
> + status = "disabled";
> + compatible = "gpio-leds";
> + pinctrl-0 = <&pmx_hddled_20 &pmx_hddled_21 &pmx_hddled_22
> + &pmx_hddled_23 &pmx_hddled_24 &pmx_hddled_25
> + &pmx_hddled_26 &pmx_hddled_27>;
> + pinctrl-names = "default";
> + hdd1-green {
> + label = "synology:green:hdd1";
> + gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
> + };
> + hdd1-amber {
> + label = "synology:amber:hdd1";
> + gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
> + };
> + hdd2-green {
> + label = "synology:green:hdd2";
> + gpios = <&gpio0 22 GPIO_ACTIVE_LOW>;
> + };
> + hdd2-amber {
> + label = "synology:amber:hdd2";
> + gpios = <&gpio0 23 GPIO_ACTIVE_LOW>;
> + };
> + hdd3-green {
> + label = "synology:green:hdd3";
> + gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
> + };
> + hdd3-amber {
> + label = "synology:amber:hdd3";
> + gpios = <&gpio0 25 GPIO_ACTIVE_LOW>;
> + };
> + hdd4-green {
> + label = "synology:green:hdd4";
> + gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
> + };
> + hdd4-amber {
> + label = "synology:amber:hdd4";
> + gpios = <&gpio0 27 GPIO_ACTIVE_LOW>;
> + };
> + };
> + gpio-leds-hdd-21-1 {
> + status = "disabled";
> + compatible = "gpio-leds";
> + pinctrl-0 = <&pmx_hddled_21 &pmx_hddled_23>;
> + pinctrl-names = "default";
> + hdd1-green {
> + label = "synology:green:hdd1";
> + gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
> + };
> + hdd1-amber {
> + label = "synology:amber:hdd1";
> + gpios = <&gpio0 23 GPIO_ACTIVE_LOW>;
> + };
> + };
> + gpio-leds-hdd-21-2 {
> + status = "disabled";
> + compatible = "gpio-leds";
> + pinctrl-0 = <&pmx_hddled_21 &pmx_hddled_23 &pmx_hddled_20 &pmx_hddled_22>;
> + pinctrl-names = "default";
> + hdd1-green {
> + label = "synology:green:hdd1";
> + gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
> + };
> + hdd1-amber {
> + label = "synology:amber:hdd1";
> + gpios = <&gpio0 23 GPIO_ACTIVE_LOW>;
> + };
> + hdd2-green {
> + label = "synology:green:hdd2";
> + gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
> + };
> + hdd2-amber {
> + label = "synology:amber:hdd2";
> + gpios = <&gpio0 22 GPIO_ACTIVE_LOW>;
> + };
> + };
> + gpio-leds-hdd-36 {
> + status = "disabled";
> + compatible = "gpio-leds";
> + pinctrl-0 = <&pmx_hddled_36 &pmx_hddled_37 &pmx_hddled_38
> + &pmx_hddled_39 &pmx_hddled_40 &pmx_hddled_41
> + &pmx_hddled_42 &pmx_hddled_43 &pmx_hddled_44
> + &pmx_hddled_45>;
> + pinctrl-names = "default";
> + hdd1-green {
> + label = "synology:green:hdd1";
> + gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
> + };
> + hdd1-amber {
> + label = "synology:amber:hdd1";
> + gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
> + };
> + hdd2-green {
> + label = "synology:green:hdd2";
> + gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
> + };
> + hdd2-amber {
> + label = "synology:amber:hdd2";
> + gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
> + };
> + hdd3-green {
> + label = "synology:green:hdd3";
> + gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
> + };
> + hdd3-amber {
> + label = "synology:amber:hdd3";
> + gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
> + };
> + hdd4-green {
> + label = "synology:green:hdd4";
> + gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
> + };
> + hdd4-amber {
> + label = "synology:amber:hdd4";
> + gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
> + };
> + hdd5-green {
> + label = "synology:green:hdd5";
> + gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
> + };
> + hdd5-amber {
> + label = "synology:amber:hdd5";
> + gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
> + };
> + };
> + gpio-leds-hdd-38 {
> + status = "disabled";
> + compatible = "gpio-leds";
> + pinctrl-0 = <&pmx_hddled_38 &pmx_hddled_39 &pmx_hddled_36 &pmx_hddled_37>;
> + pinctrl-names = "default";
> + hdd1-green {
> + label = "synology:green:hdd1";
> + gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
> + };
> + hdd1-amber {
> + label = "synology:amber:hdd1";
> + gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
> + };
> + hdd2-green {
> + label = "synology:green:hdd2";
> + gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
> + };
> + hdd2-amber {
> + label = "synology:amber:hdd2";
> + gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
> + };
> + };
> + regulators-hdd-29 {
> + status = "disabled";
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-0 = <&pmx_hdd1_pwr_29 &pmx_hdd2_pwr_31>;
> + pinctrl-names = "default";
> +
> + regulator@1 {
> + compatible = "regulator-fixed";
> + reg = <1>;
> + regulator-name = "hdd1power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + startup-delay-us = <5000000>;
> + gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
> + };
> + regulator@2 {
> + compatible = "regulator-fixed";
> + reg = <2>;
> + regulator-name = "hdd2power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + startup-delay-us = <5000000>;
> + gpio = <&gpio0 31 GPIO_ACTIVE_HIGH>;
> + };
> + };
> + regulators-hdd-30-1 {
> + status = "disabled";
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-0 = <&pmx_hdd1_pwr_30>;
> + pinctrl-names = "default";
> +
> + regulator@1 {
> + compatible = "regulator-fixed";
> + reg = <1>;
> + regulator-name = "hdd1power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + startup-delay-us = <5000000>;
> + gpio = <&gpio0 30 GPIO_ACTIVE_HIGH>;
> + };
> + };
> + regulators-hdd-30-2 {
> + status = "disabled";
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-0 = <&pmx_hdd1_pwr_30 &pmx_hdd2_pwr_34>;
> + pinctrl-names = "default";
> +
> + regulator@1 {
> + compatible = "regulator-fixed";
> + reg = <1>;
> + regulator-name = "hdd1power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + startup-delay-us = <5000000>;
> + gpio = <&gpio0 30 GPIO_ACTIVE_HIGH>;
> + };
> + regulator@2 {
> + compatible = "regulator-fixed";
> + reg = <2>;
> + regulator-name = "hdd2power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + startup-delay-us = <5000000>;
> + gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
> + };
> + };
> + regulators-hdd-30-4 {
> + status = "disabled";
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-0 = <&pmx_hdd1_pwr_30 &pmx_hdd2_pwr_34
> + &pmx_hdd3_pwr_44 &pmx_hdd4_pwr_45>;
> + pinctrl-names = "default";
> +
> + regulator@1 {
> + compatible = "regulator-fixed";
> + reg = <1>;
> + regulator-name = "hdd1power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + startup-delay-us = <5000000>;
> + gpio = <&gpio0 30 GPIO_ACTIVE_HIGH>;
> + };
> + regulator@2 {
> + compatible = "regulator-fixed";
> + reg = <2>;
> + regulator-name = "hdd2power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + startup-delay-us = <5000000>;
> + gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
> + };
> + regulator@3 {
> + compatible = "regulator-fixed";
> + reg = <3>;
> + regulator-name = "hdd3power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + startup-delay-us = <5000000>;
> + gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
> + };
> + regulator@4 {
> + compatible = "regulator-fixed";
> + reg = <4>;
> + regulator-name = "hdd4power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + startup-delay-us = <5000000>;
> + gpio = <&gpio1 13 GPIO_ACTIVE_HIGH>;
> + };
> + };
> + regulators-hdd-31 {
> + status = "disabled";
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-0 = <&pmx_hdd2_pwr_31>;
> + pinctrl-names = "default";
> +
> + regulator@1 {
> + compatible = "regulator-fixed";
> + reg = <1>;
> + regulator-name = "hdd2power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + startup-delay-us = <5000000>;
> + gpio = <&gpio0 31 GPIO_ACTIVE_HIGH>;
> + };
> + };
> + regulators-hdd-34 {
> + status = "disabled";
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-0 = <&pmx_hdd2_pwr_34 &pmx_hdd3_pwr_44
> + &pmx_hdd4_pwr_45>;
> + pinctrl-names = "default";
> +
> + regulator@2 {
> + compatible = "regulator-fixed";
> + reg = <2>;
> + regulator-name = "hdd2power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + startup-delay-us = <5000000>;
> + gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
> + };
> + regulator@3 {
> + compatible = "regulator-fixed";
> + reg = <3>;
> + regulator-name = "hdd3power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + startup-delay-us = <5000000>;
> + gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
> + };
> + regulator@4 {
> + compatible = "regulator-fixed";
> + reg = <4>;
> + regulator-name = "hdd4power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + startup-delay-us = <5000000>;
> + gpio = <&gpio1 13 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +};
> +
> +&mdio {
> + status = "okay";
> +
> + ethphy0: ethernet-phy@0 {
> + device_type = "ethernet-phy";
> + reg = <8>;
> + };
> + ethphy1: ethernet-phy@1 {
> + device_type = "ethernet-phy";
> + reg = <9>;
> + };
> +};
> +
> +ð0 {
> + status = "okay";
> + ethernet0-port@0 {
> + phy-handle = <ðphy0>;
> + };
> +};
> +
> +ð1 {
> + status = "disabled";
> + ethernet1-port@0 {
> + phy-handle = <ðphy1>;
> + };
> +};
> diff --git a/arch/arm/boot/dts/kirkwood-ds109.dts b/arch/arm/boot/dts/kirkwood-ds109.dts
> new file mode 100644
> index 0000000..9320166
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-ds109.dts
> @@ -0,0 +1,42 @@
> +/*
> + * Andrew Lunn <andrew@xxxxxxx>
> + * Ben Peddell <klightspeed@xxxxxxxxxxxxxxxx>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6281.dtsi"
> +#include "kirkwood-ds-rs-common.dtsi"
> +
> +/ {
> + model = "Synology DS109, DS110, DS110jv20";
> + compatible = "synology,ds109", "synology,ds110jv20",
> + "synology,ds110", "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x8000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +
> + gpio-fan-150-32-35 {
> + status = "okay";
> + };
> +
> + gpio-leds-hdd-21-1 {
> + status = "okay";
> + };
> +};
> +
> +&rs5c372 {
> + status = "okay";
> +};
> +
> diff --git a/arch/arm/boot/dts/kirkwood-ds110jv10.dts b/arch/arm/boot/dts/kirkwood-ds110jv10.dts
> new file mode 100644
> index 0000000..09d4fbb
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-ds110jv10.dts
> @@ -0,0 +1,41 @@
> +/*
> + * Andrew Lunn <andrew@xxxxxxx>
> + * Ben Peddell <klightspeed@xxxxxxxxxxxxxxxx>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6281.dtsi"
> +#include "kirkwood-ds-rs-common.dtsi"
> +
> +/ {
> + model = "Synology DS110j v10 and v30";
> + compatible = "synology,ds110jv10", "synology,ds110jv30",
> + "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x8000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +
> + gpio-fan-150-32-35 {
> + status = "okay";
> + };
> +
> + gpio-leds-hdd-21-1 {
> + status = "okay";
> + };
> +};
> +
> +&s35390a {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/kirkwood-ds111.dts b/arch/arm/boot/dts/kirkwood-ds111.dts
> new file mode 100644
> index 0000000..0369204
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-ds111.dts
> @@ -0,0 +1,44 @@
> +/*
> + * Andrew Lunn <andrew@xxxxxxx>
> + * Ben Peddell <klightspeed@xxxxxxxxxxxxxxxx>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6282.dtsi"
> +#include "kirkwood-ds-rs-common.dtsi"
> +
> +/ {
> + model = "Synology DS111";
> + compatible = "synology,ds111", "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x8000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +
> + gpio-fan-100-15-35-1 {
> + status = "okay";
> + };
> +
> + gpio-leds-hdd-21-1 {
> + status = "okay";
> + };
> +};
> +
> +&s35390a {
> + status = "okay";
> +};
> +
> +&pcie2 {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/kirkwood-ds112.dts b/arch/arm/boot/dts/kirkwood-ds112.dts
> new file mode 100644
> index 0000000..9a70bf9
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-ds112.dts
> @@ -0,0 +1,48 @@
> +/*
> + * Andrew Lunn <andrew@xxxxxxx>
> + * Ben Peddell <klightspeed@xxxxxxxxxxxxxxxx>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6282.dtsi"
> +#include "kirkwood-ds-rs-common.dtsi"
> +
> +/ {
> + model = "Synology DS111";
> + compatible = "synology,ds111", "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x8000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +
> + gpio-fan-100-15-35-1 {
> + status = "okay";
> + };
> +
> + gpio-leds-21-2 {
> + status = "okay";
> + };
> +
> + regulators-hdd-30 {
> + status = "okay";
> + };
> +};
> +
> +&s35390a {
> + status = "okay";
> +};
> +
> +&pcie2 {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/kirkwood-ds209.dts b/arch/arm/boot/dts/kirkwood-ds209.dts
> new file mode 100644
> index 0000000..466f584
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-ds209.dts
> @@ -0,0 +1,44 @@
> +/*
> + * Andrew Lunn <andrew@xxxxxxx>
> + * Ben Peddell <klightspeed@xxxxxxxxxxxxxxxx>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6281.dtsi"
> +#include "kirkwood-ds-rs-common.dtsi"
> +
> +/ {
> + model = "Synology DS209";
> + compatible = "synology,ds209", "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x8000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +
> + gpio-fan-150-32-35 {
> + status = "okay";
> + };
> +
> + gpio-leds-hdd-21-2 {
> + status = "okay";
> + };
> +
> + regulators-hdd-31 {
> + status = "okay";
> + };
> +};
> +
> +&rs5c372 {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/kirkwood-ds210.dts b/arch/arm/boot/dts/kirkwood-ds210.dts
> new file mode 100644
> index 0000000..0d8a0e1
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-ds210.dts
> @@ -0,0 +1,46 @@
> +/*
> + * Andrew Lunn <andrew@xxxxxxx>
> + * Ben Peddell <klightspeed@xxxxxxxxxxxxxxxx>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6281.dtsi"
> +#include "kirkwood-ds-rs-common.dtsi"
> +
> +/ {
> + model = "Synology DS210 v10, v20, v30, DS211j";
> + compatible = "synology,ds210jv10", "synology,ds210jv20",
> + "synology,ds210jv30", "synology,ds211j",
> + "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x8000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +
> + gpio-fan-150-32-35 {
> + status = "okay";
> + };
> +
> + gpio-leds-hdd-21-2 {
> + status = "okay";
> + };
> +
> + regulators-hdd-31 {
> + status = "okay";
> + };
> +};
> +
> +&s35390a {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/kirkwood-ds212.dts b/arch/arm/boot/dts/kirkwood-ds212.dts
> new file mode 100644
> index 0000000..dd0374e
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-ds212.dts
> @@ -0,0 +1,47 @@
> +/*
> + * Andrew Lunn <andrew@xxxxxxx>
> + * Ben Peddell <klightspeed@xxxxxxxxxxxxxxxx>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6282.dtsi"
> +#include "kirkwood-ds-rs-common.dtsi"
> +
> +/ {
> + model = "Synology DS212, DS212p v10, v20, DS213air v10, DS213 v10";
> + compatible = "synology,ds212", "synology,ds212pv10",
> + "synology,ds212pv10", "synology,ds212pv20",
> + "synology,ds213airv10", "synology,ds213v10",
> + "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x8000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +
> + gpio-fan-100-15-35-1 {
> + status = "okay";
> + };
> +
> + gpio-leds-hdd-21-2 {
> + status = "okay";
> + };
> +};
> +
> +&s35390a {
> + status = "okay";
> +};
> +
> +&pcie2 {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/kirkwood-ds212j.dts b/arch/arm/boot/dts/kirkwood-ds212j.dts
> new file mode 100644
> index 0000000..7328044
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-ds212j.dts
> @@ -0,0 +1,41 @@
> +/*
> + * Andrew Lunn <andrew@xxxxxxx>
> + * Ben Peddell <klightspeed@xxxxxxxxxxxxxxxx>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6281.dtsi"
> +#include "kirkwood-ds-rs-common.dtsi"
> +
> +/ {
> + model = "Synology DS212j v10, v20";
> + compatible = "synology,ds212jv10", "synology,ds212jv20",
> + "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x8000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +
> + gpio-fan-100-32-35 {
> + status = "okay";
> + };
> +
> + gpio-leds-hdd-21-2 {
> + status = "okay";
> + };
> +};
> +
> +&s35390a {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/kirkwood-ds409.dts b/arch/arm/boot/dts/kirkwood-ds409.dts
> new file mode 100644
> index 0000000..c6aa57b
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-ds409.dts
> @@ -0,0 +1,48 @@
> +/*
> + * Andrew Lunn <andrew@xxxxxxx>
> + * Ben Peddell <klightspeed@xxxxxxxxxxxxxxxx>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6281.dtsi"
> +#include "kirkwood-ds-rs-common.dtsi"
> +
> +/ {
> + model = "Synology DS409, DS410j";
> + compatible = "synology,ds409", "synology,ds410j", "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x8000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +
> + gpio-fan-150-15-18 {
> + status = "okay";
> + };
> +
> + gpio-leds-hdd-36 {
> + status = "okay";
> + };
> +
> + gpio-leds-alarm-12 {
> + status = "okay";
> + };
> +};
> +
> +ð1 {
> + status = "okay";
> +};
> +
> +&rs5c372 {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/kirkwood-ds409slim.dts b/arch/arm/boot/dts/kirkwood-ds409slim.dts
> new file mode 100644
> index 0000000..3c7b5bd
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-ds409slim.dts
> @@ -0,0 +1,40 @@
> +/*
> + * Andrew Lunn <andrew@xxxxxxx>
> + * Ben Peddell <klightspeed@xxxxxxxxxxxxxxxx>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6281.dtsi"
> +#include "kirkwood-ds-rs-common.dtsi"
> +
> +/ {
> + model = "Synology 409slim";
> + compatible = "synology,ds409slim", "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x8000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +
> + gpio-fan-150-32-35 {
> + status = "okay";
> + };
> +
> + gpio-leds-hdd-20 {
> + status = "okay";
> + };
> +};
> +
> +&rs5c372 {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/kirkwood-ds411.dts b/arch/arm/boot/dts/kirkwood-ds411.dts
> new file mode 100644
> index 0000000..c8aa152
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-ds411.dts
> @@ -0,0 +1,52 @@
> +/*
> + * Andrew Lunn <andrew@xxxxxxx>
> + * Ben Peddell <klightspeed@xxxxxxxxxxxxxxxx>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6282.dtsi"
> +#include "kirkwood-ds-rs-common.dtsi"
> +
> +/ {
> + model = "Synology DS411, DS413jv10";
> + compatible = "synology,ds411", "synology,ds413jv10", "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x8000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +
> + gpio-fan-100-15-35-1 {
> + status = "okay";
> + };
> +
> + gpio-leds-hdd-36 {
> + status = "okay";
> + };
> +
> + regulators-hdd-34 {
> + status = "okay";
> + };
> +};
> +
> +ð1 {
> + status = "okay";
> +};
> +
> +&s35390a {
> + status = "okay";
> +};
> +
> +&pcie2 {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/kirkwood-ds411j.dts b/arch/arm/boot/dts/kirkwood-ds411j.dts
> new file mode 100644
> index 0000000..9546a2d
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-ds411j.dts
> @@ -0,0 +1,48 @@
> +/*
> + * Andrew Lunn <andrew@xxxxxxx>
> + * Ben Peddell <klightspeed@xxxxxxxxxxxxxxxx>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6281.dtsi"
> +#include "kirkwood-ds-rs-common.dtsi"
> +
> +/ {
> + model = "Synology DS411j";
> + compatible = "synology,ds411j", "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x8000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +
> + gpio-fan-150-15-18 {
> + status = "okay";
> + };
> +
> + gpio-leds-hdd-36 {
> + status = "okay";
> + };
> +
> + gpio-leds-alarm-12 {
> + status = "okay";
> + };
> +};
> +
> +ð1 {
> + status = "okay";
> +};
> +
> +&s35390a {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/kirkwood-ds411slim.dts b/arch/arm/boot/dts/kirkwood-ds411slim.dts
> new file mode 100644
> index 0000000..b2d8ea8
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-ds411slim.dts
> @@ -0,0 +1,48 @@
> +/*
> + * Andrew Lunn <andrew@xxxxxxx>
> + * Ben Peddell <klightspeed@xxxxxxxxxxxxxxxx>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6282.dtsi"
> +#include "kirkwood-ds-rs-common.dtsi"
> +
> +/ {
> + model = "Synology DS411slim";
> + compatible = "synology,ds411slim", "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x8000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +
> + gpio-fan-100-15-35-1 {
> + status = "okay";
> + };
> +
> + gpio-leds-hdd-36 {
> + status = "okay";
> + };
> +};
> +
> +ð1 {
> + status = "okay";
> +};
> +
> +&s35390a {
> + status = "okay";
> +};
> +
> +&pcie2 {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/kirkwood-rs212.dts b/arch/arm/boot/dts/kirkwood-rs212.dts
> new file mode 100644
> index 0000000..3efad06
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-rs212.dts
> @@ -0,0 +1,48 @@
> +/*
> + * Andrew Lunn <andrew@xxxxxxx>
> + * Ben Peddell <klightspeed@xxxxxxxxxxxxxxxx>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6282.dtsi"
> +#include "kirkwood-ds-rs-common.dtsi"
> +
> +/ {
> + model = "Synology RS212";
> + compatible = "synology,rs212", "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x8000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +
> + gpio-fan-100-15-35-3 {
> + status = "okay";
> + };
> +
> + gpio-leds-hdd-38 {
> + status = "okay";
> + };
> +
> + regulators-hdd-30-2 {
> + status = "okay";
> + };
> +};
> +
> +&s35390a {
> + status = "okay";
> +};
> +
> +&pcie2 {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/kirkwood-rs409.dts b/arch/arm/boot/dts/kirkwood-rs409.dts
> new file mode 100644
> index 0000000..cddd620
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-rs409.dts
> @@ -0,0 +1,44 @@
> +/*
> + * Andrew Lunn <andrew@xxxxxxx>
> + * Ben Peddell <klightspeed@xxxxxxxxxxxxxxxx>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6281.dtsi"
> +#include "kirkwood-ds-rs-common.dtsi"
> +
> +/ {
> + model = "Synology RS409";
> + compatible = "synology,rs409", "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x8000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +
> + gpio-fan-150-15-18 {
> + status = "okay";
> + };
> +
> + gpio-leds-hdd-36 {
> + status = "okay";
> + };
> +};
> +
> +ð1 {
> + status = "okay";
> +};
> +
> +&rs5c372 {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/kirkwood-rs411.dts b/arch/arm/boot/dts/kirkwood-rs411.dts
> new file mode 100644
> index 0000000..a337a5c
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-rs411.dts
> @@ -0,0 +1,44 @@
> +/*
> + * Andrew Lunn <andrew@xxxxxxx>
> + * Ben Peddell <klightspeed@xxxxxxxxxxxxxxxx>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6282.dtsi"
> +#include "kirkwood-ds-rs-common.dtsi"
> +
> +/ {
> + model = "Synology RS411 RS812";
> + compatible = "synology,rs411", "synology,rs812", "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x8000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +
> + gpio-fan-100-15-35-3 {
> + status = "okay";
> + };
> +
> + gpio-leds-hdd-36 {
> + status = "okay";
> + };
> +};
> +
> +ð1 {
> + status = "okay";
> +};
> +
> +&s35390a {
> + status = "okay";
> +};
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
