Hardware Info ------------- Processor - Broadcom BCM4709C0KFEBG dual-core @ 1.4 GHz Switch - BCM53012 in BCM4709C0KFEBG & external BCM53125 DDR3 RAM - 256 MB Flash - 128 MB (Toshiba TC58BVG0S3HTA00) 2.4GHz - BCM4366 4×4 2.4/5G single chip 802.11ac SoC Power Amp - Skyworks SE2623L 2.4 GHz power amp (x4) 5GHz x 2 - BCM4366 4×4 2.4/5G single chip 802.11ac SoC Power Amp - PLX Technology PEX8603 3-lane, 3-port PCIe switch Ports - 8 Ports, 1 WAN Ports Antennas - 8 Antennas Serial Port - @J6 [GND,TX,RX] (VCC NC) 115200 8n1 Tested with OpenWrt built with DSA driver and Kernel v4.14 Note: "make sure that port 0 of the internal switch is not accidentally configured back to untagged since that would cause problem when terminating the VLAN tag on the SW side." - Florian Fainelli [1] This can be ensured by running following command in OpenWrt: bridge vlan add vid 1 dev extsw pvid tagged [1] https://www.spinics.net/lists/arm-kernel/msg590992.html Signed-off-by: Vivek Unune <npcomplete13@xxxxxxxxx> --- Changes in v2: - Properly define mdio mux, internal mdio, external mdio, mii bus - Now we define usb3 phy as a mdio node connected to internal mdio, thanks to work done by Rafał Miłecki on the bcm usb3 phy mdio driver - Define external SW as a mdio-mii node connected to external mdio --- arch/arm/boot/dts/bcm47094-linksys-panamera.dts | 239 +++++++++++++++++++++++- arch/arm/boot/dts/bcm47094.dtsi | 6 +- arch/arm/boot/dts/bcm5301x.dtsi | 55 +++++- 3 files changed, 288 insertions(+), 12 deletions(-) diff --git a/arch/arm/boot/dts/bcm47094-linksys-panamera.dts b/arch/arm/boot/dts/bcm47094-linksys-panamera.dts index b6750f7..5f53207 100644 --- a/arch/arm/boot/dts/bcm47094-linksys-panamera.dts +++ b/arch/arm/boot/dts/bcm47094-linksys-panamera.dts @@ -7,7 +7,7 @@ /dts-v1/; #include "bcm47094.dtsi" -#include "bcm5301x-nand-cs0-bch8.dtsi" +#include "bcm5301x-nand-cs0-bch1.dtsi" / { compatible = "linksys,panamera", "brcm,bcm47094", "brcm,bcm4708"; @@ -32,5 +32,242 @@ linux,code = <KEY_WPS_BUTTON>; gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>; }; + + rfkill { + label = "WiFi"; + linux,code = <KEY_RFKILL>; + gpios = <&chipcommon 16 GPIO_ACTIVE_LOW>; + }; + + reset { + label = "Reset"; + linux,code = <KEY_RESTART>; + gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>; + }; + }; + + leds { + compatible = "gpio-leds"; + + wps { + label = "bcm53xx:white:wps"; + gpios = <&chipcommon 22 GPIO_ACTIVE_LOW>; + }; + + usb2 { + label = "bcm53xx:green:usb2"; + gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>; + trigger-sources = <&ohci_port2>, <&ehci_port2>; + linux,default-trigger = "usbport"; + }; + + usb3 { + label = "bcm53xx:green:usb3"; + gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>; + trigger-sources = <&ohci_port1>, <&ehci_port1>, + <&xhci_port1>; + linux,default-trigger = "usbport"; + }; + + power { + label = "bcm53xx:white:power"; + gpios = <&chipcommon 4 GPIO_ACTIVE_HIGH>; + }; + + wifi-disabled { + label = "bcm53xx:amber:wifi-disabled"; + gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>; + }; + + wifi-enabled { + label = "bcm53xx:white:wifi-enabled"; + gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>; + }; + + bluebar1 { + label = "bcm53xx:white:bluebar1"; + gpios = <&chipcommon 11 GPIO_ACTIVE_HIGH>; + }; + + bluebar2 { + label = "bcm53xx:white:bluebar2"; + gpios = <&chipcommon 12 GPIO_ACTIVE_HIGH>; + }; + + bluebar3 { + label = "bcm53xx:white:bluebar3"; + gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>; + }; + + bluebar4 { + label = "bcm53xx:white:bluebar4"; + gpios = <&chipcommon 18 GPIO_ACTIVE_HIGH>; + }; + + bluebar5 { + label = "bcm53xx:white:bluebar5"; + gpios = <&chipcommon 19 GPIO_ACTIVE_HIGH>; + }; + + bluebar6 { + label = "bcm53xx:white:bluebar6"; + gpios = <&chipcommon 20 GPIO_ACTIVE_HIGH>; + }; + + bluebar7 { + label = "bcm53xx:white:bluebar7"; + gpios = <&chipcommon 21 GPIO_ACTIVE_HIGH>; + }; + + bluebar8 { + label = "bcm53xx:white:bluebar8"; + gpios = <&chipcommon 8 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&usb2 { + vcc-gpio = <&chipcommon 13 GPIO_ACTIVE_HIGH>; +}; + +&usb3 { + vcc-gpio = <&chipcommon 14 GPIO_ACTIVE_HIGH>; +}; + +&mdio_mii_mux { + status = "okay"; +}; + +&mdio_ext { + status = "okay"; +}; + +&srab { + compatible = "brcm,bcm53012-srab", "brcm,bcm5301x-srab"; + status = "okay"; + dsa,member = <0 0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>; + label = "lan7"; + }; + + port@2 { + reg = <2>; + label = "lan4"; + }; + + port@3 { + reg = <3>; + label = "lan8"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@5 { + reg = <5>; + ethernet = <&gmac0>; + label = "cpu"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + port@7 { + reg = <7>; + ethernet = <&gmac1>; + label = "cpu"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + port@8 { + reg = <8>; + ethernet = <&gmac2>; + label = "cpu"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + sw0_p0: port@0 { + reg = <0>; + label = "extsw"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; }; }; + +&mdio_mii { + status = "okay"; + + switch@0 { + compatible = "brcm,bcm53125"; + #address-cells = <1>; + #size-cells = <0>; + reset-gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>; + reset-names = "robo_reset"; + reg = <0>; + dsa,member = <1 0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan5"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan6"; + }; + + port@4 { + reg = <4>; + label = "lan3"; + }; + + sw1_p8: port@8 { + reg = <8>; + ethernet = <&sw0_p0>; + label = "cpu"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; +}; + diff --git a/arch/arm/boot/dts/bcm47094.dtsi b/arch/arm/boot/dts/bcm47094.dtsi index 4840a78..8f3ec57 100644 --- a/arch/arm/boot/dts/bcm47094.dtsi +++ b/arch/arm/boot/dts/bcm47094.dtsi @@ -6,10 +6,8 @@ #include "bcm4708.dtsi" -/ { - usb3_phy: usb3-phy { - compatible = "brcm,ns-bx-usb3-phy"; - }; +&usb3_phy { + compatible = "brcm,ns-bx-usb3-phy"; }; &uart0 { diff --git a/arch/arm/boot/dts/bcm5301x.dtsi b/arch/arm/boot/dts/bcm5301x.dtsi index 9a076c4..9e4386a 100644 --- a/arch/arm/boot/dts/bcm5301x.dtsi +++ b/arch/arm/boot/dts/bcm5301x.dtsi @@ -154,13 +154,6 @@ clock-names = "phy-ref-clk"; }; - usb3_phy: usb3-phy { - compatible = "brcm,ns-ax-usb3-phy"; - reg = <0x18105000 0x1000>, <0x18003000 0x1000>; - reg-names = "dmp", "ccb-mii"; - #phy-cells = <0>; - }; - axi@18000000 { compatible = "brcm,bus-axi"; reg = <0x18000000 0x1000>; @@ -359,7 +352,55 @@ reg = <0x18003000 0x8>; #size-cells = <1>; #address-cells = <0>; + }; + + mdio-bus-mux { + compatible = "mdio-mux-mmioreg"; + mdio-parent-bus = <&mdio>; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x18003000 0x4>; + mux-mask = <0x200>; + + mdio_int: mdio@0 { /* BIT(9) = 0 => internal mdio */ + reg = <0x0>; + #address-cells = <1>; + #size-cells = <0>; + + usb3_phy: usb3-phy@10 { + compatible = "brcm,ns-ax-usb3-phy"; + reg = <0x10>; + usb3-dmp-syscon = <&usb3_dmp>; + #phy-cells = <0>; + }; + }; + + mdio_ext: mdio@200 { /* BIT(9) = 1 => external mdio */ + reg = <0x200>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + }; + + mdio_mii_mux: mdio-mii-mux { + compatible = "mdio-mux-mmioreg"; + mdio-parent-bus = <&mdio_ext>; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x1800c1c0 0x4>; + mux-mask = <0xc0>; /* BIT(6) = mdc, BIT(7) = mdio */ status = "disabled"; + + mdio_mii: mdio-mii@0 { + reg = <0x0>; /* Enable mii function */ + #address-cells = <1>; + #size-cells = <0>; + }; + }; + + usb3_dmp: syscon@18105000 { + reg = <0x18105000 0x1000>; }; i2c0: i2c@18009000 { -- 2.9.3 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
