Hi Bough,
On Sat, Feb 24, 2018 at 02:58:31AM +0000, Bough Chen wrote:
> >Am Freitag, den 23.02.2018, 16:30 +0100 schrieb Juergen Borleis:
> >> On Friday 23 February 2018 16:03:53 Shawn Guo wrote:
> >> > On Thu, Feb 01, 2018 at 07:31:25PM +0100, Lucas Stach wrote:
> >> > > +&usdhc1 {
> >> > > + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> >> > > + pinctrl-0 = <&pinctrl_usdhc1_cd_reset>,
> >> <&pinctrl_usdhc1_clk_strobe>,
> >> > > + <&pinctrl_usdhc1_data>;
> >> > > + pinctrl-1 = <&pinctrl_usdhc1_cd_reset>,
> >> > > + <&pinctrl_usdhc1_clk_strobe_100mhz>,
> >> > > + <&pinctrl_usdhc1_data_100mhz>;
> >> > > + pinctrl-2 = <&pinctrl_usdhc1_cd_reset>,
> >> > > + <&pinctrl_usdhc1_clk_strobe_200mhz>,
> >> > > + <&pinctrl_usdhc1_data_200mhz>;
> >> > > + vqmmc-supply = <&sw4_reg>;
> >> > > + bus-width = <8>;
> >> > > + non-removable;
> >> > > + no-sd;
> >> > > + no-sdio;
> >> > > + status = "okay";
> >> > > +};
> >> >
>
> EMMC do not need cd pin, and I notice that pinctrl_usdhc1_cd_reset also contains a usdhc2 pad, this is wrong. So please remove pinctrl_usdhc1_cd_reset.
> EMMC I/O voltage is fixed to 1.8v so I think no need to add vqmmc-supply, can remove this property here.
> For pinctrl_usdhc1_clk_strobe, clock pad need to be pull down, otherwise you will meet data crc error in hs400 mode.
Thanks for the input. I suspect that there are more than what you
suggest here. I remove vqmmc-supply and use the exactly same
pinctrl_usdhc1 as NXP kernel, but still see errors below.
[ 0.952795] mmc0: SDHCI controller on 30b40000.usdhc [30b40000.usdhc] using ADMA
[ 1.054622] mmc0: Tuning failed, falling back to fixed sampling clock
[ 1.076458] mmc0: new HS400 MMC card at address 0001
[ 1.081980] mmcblk0: mmc0:0001 R1J56L 13.8 GiB
[ 1.086880] mmcblk0boot0: mmc0:0001 R1J56L partition 1 4.00 MiB
[ 1.093156] mmcblk0boot1: mmc0:0001 R1J56L partition 2 4.00 MiB
[ 1.099220] mmcblk0rpmb: mmc0:0001 R1J56L partition 3 128 KiB, chardev (248:0)
[ 1.148214] mmc0: Tuning failed, falling back to fixed sampling clock
[ 1.266704] print_req_error: I/O error, dev mmcblk0, sector 0
[ 1.273487] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[ 1.358863] print_req_error: I/O error, dev mmcblk0, sector 0
[ 1.365640] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[ 1.372816] mmcblk0: unable to read partition table
[ 7.231120] mmc0: switch to high-speed from hs200 failed, err:-110
[ 7.372241] mmc0: switch to high-speed from hs200 failed, err:-110
[ 7.378843] print_req_error: I/O error, dev mmcblk0, sector 0
Shawn
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
