> +static int peci_locked_xfer(struct peci_adapter *adapter,
> + struct peci_xfer_msg *msg,
> + bool do_retry,
> + bool has_aw_fcs)
> +{
> + ktime_t start, end;
> + s64 elapsed_ms;
> + int rc = 0;
> +
> + if (!adapter->xfer) {
> + dev_dbg(&adapter->dev, "PECI level transfers not supported\n");
> + return -ENODEV;
> + }
> +
> + if (in_atomic() || irqs_disabled()) {
Hi Jae
Is there a real need to do transfers in atomic context, or with
interrupts disabled?
> + rt_mutex_trylock(&adapter->bus_lock);
> + if (!rc)
> + return -EAGAIN; /* PECI activity is ongoing */
> + } else {
> + rt_mutex_lock(&adapter->bus_lock);
> + }
> +
> + if (do_retry)
> + start = ktime_get();
> +
> + do {
> + rc = adapter->xfer(adapter, msg);
> +
> + if (!do_retry)
> + break;
> +
> + /* Per the PECI spec, need to retry commands that return 0x8x */
> + if (!(!rc && ((msg->rx_buf[0] & DEV_PECI_CC_RETRY_ERR_MASK) ==
> + DEV_PECI_CC_TIMEOUT)))
> + break;
> +
> + /* Set the retry bit to indicate a retry attempt */
> + msg->tx_buf[1] |= DEV_PECI_RETRY_BIT;
> +
> + /* Recalculate the AW FCS if it has one */
> + if (has_aw_fcs)
> + msg->tx_buf[msg->tx_len - 1] = 0x80 ^
> + peci_aw_fcs((u8 *)msg,
> + 2 + msg->tx_len);
> +
> + /* Retry for at least 250ms before returning an error */
> + end = ktime_get();
> + elapsed_ms = ktime_to_ms(ktime_sub(end, start));
> + if (elapsed_ms >= DEV_PECI_RETRY_TIME_MS) {
> + dev_dbg(&adapter->dev, "Timeout retrying xfer!\n");
> + break;
> + }
> + } while (true);
So you busy loop to 1/4 second? How about putting a sleep in here so
other things can be done between each retry.
And should it not return -ETIMEDOUT after that 1/4 second?
> +static int peci_scan_cmd_mask(struct peci_adapter *adapter)
> +{
> + struct peci_xfer_msg msg;
> + u32 dib;
> + int rc = 0;
> +
> + /* Update command mask just once */
> + if (adapter->cmd_mask & BIT(PECI_CMD_PING))
> + return 0;
> +
> + msg.addr = PECI_BASE_ADDR;
> + msg.tx_len = GET_DIB_WR_LEN;
> + msg.rx_len = GET_DIB_RD_LEN;
> + msg.tx_buf[0] = GET_DIB_PECI_CMD;
> +
> + rc = peci_xfer(adapter, &msg);
> + if (rc < 0) {
> + dev_dbg(&adapter->dev, "PECI xfer error, rc : %d\n", rc);
> + return rc;
> + }
> +
> + dib = msg.rx_buf[0] | (msg.rx_buf[1] << 8) |
> + (msg.rx_buf[2] << 16) | (msg.rx_buf[3] << 24);
> +
> + /* Check special case for Get DIB command */
> + if (dib == 0x00) {
> + dev_dbg(&adapter->dev, "DIB read as 0x00\n");
> + return -1;
> + }
> +
> + if (!rc) {
> + /**
> + * setting up the supporting commands based on minor rev#
> + * see PECI Spec Table 3-1
> + */
> + dib = (dib >> 8) & 0xF;
> +
> + if (dib >= 0x1) {
> + adapter->cmd_mask |= BIT(PECI_CMD_RD_PKG_CFG);
> + adapter->cmd_mask |= BIT(PECI_CMD_WR_PKG_CFG);
> + }
> +
> + if (dib >= 0x2)
> + adapter->cmd_mask |= BIT(PECI_CMD_RD_IA_MSR);
> +
> + if (dib >= 0x3) {
> + adapter->cmd_mask |= BIT(PECI_CMD_RD_PCI_CFG_LOCAL);
> + adapter->cmd_mask |= BIT(PECI_CMD_WR_PCI_CFG_LOCAL);
> + }
> +
> + if (dib >= 0x4)
> + adapter->cmd_mask |= BIT(PECI_CMD_RD_PCI_CFG);
> +
> + if (dib >= 0x5)
> + adapter->cmd_mask |= BIT(PECI_CMD_WR_PCI_CFG);
> +
> + if (dib >= 0x6)
> + adapter->cmd_mask |= BIT(PECI_CMD_WR_IA_MSR);
Lots of magic numbers here. Can they be replaced with #defines. Also,
it looks like a switch statement could be used, with fall through.
> +
> + adapter->cmd_mask |= BIT(PECI_CMD_GET_TEMP);
> + adapter->cmd_mask |= BIT(PECI_CMD_GET_DIB);
> + adapter->cmd_mask |= BIT(PECI_CMD_PING);
> + } else {
> + dev_dbg(&adapter->dev, "Error reading DIB, rc : %d\n", rc);
> + }
> +
> + return rc;
> +}
> +
> +static int peci_ioctl_get_temp(struct peci_adapter *adapter, void *vmsg)
> +{
> + struct peci_get_temp_msg *umsg = vmsg;
> + struct peci_xfer_msg msg;
> + int rc;
> +
Is this getting the temperature?
> + rc = peci_cmd_support(adapter, PECI_CMD_GET_TEMP);
> + if (rc < 0)
> + return rc;
> +
> + msg.addr = umsg->addr;
> + msg.tx_len = GET_TEMP_WR_LEN;
> + msg.rx_len = GET_TEMP_RD_LEN;
> + msg.tx_buf[0] = GET_TEMP_PECI_CMD;
> +
> + rc = peci_xfer(adapter, &msg);
> + if (rc < 0)
> + return rc;
> +
> + umsg->temp_raw = msg.rx_buf[0] | (msg.rx_buf[1] << 8);
> +
> + return 0;
> +}
> +static long peci_ioctl(struct file *file, unsigned int iocmd, unsigned long arg)
> +{
> + struct peci_adapter *adapter = file->private_data;
> + void __user *argp = (void __user *)arg;
> + unsigned int msg_len;
> + enum peci_cmd cmd;
> + u8 *msg;
> + int rc = 0;
> +
> + dev_dbg(&adapter->dev, "ioctl, cmd=0x%x, arg=0x%lx\n", iocmd, arg);
> +
> + switch (iocmd) {
> + case PECI_IOC_PING:
> + case PECI_IOC_GET_DIB:
> + case PECI_IOC_GET_TEMP:
> + case PECI_IOC_RD_PKG_CFG:
> + case PECI_IOC_WR_PKG_CFG:
> + case PECI_IOC_RD_IA_MSR:
> + case PECI_IOC_RD_PCI_CFG:
> + case PECI_IOC_RD_PCI_CFG_LOCAL:
> + case PECI_IOC_WR_PCI_CFG_LOCAL:
> + cmd = _IOC_TYPE(iocmd) - PECI_IOC_BASE;
> + msg_len = _IOC_SIZE(iocmd);
> + break;
Adding new ioctl calls is pretty frowned up. Can you export this info
via /sysfs?
Also, should there be some permission checks here? Or is any user
allowed to call these ioctls?
Andrew
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
