Introduction of the Platform Environment Control Interface (PECI) bus
device driver. PECI is a one-wire bus interface that provides a
communication channel between Intel processor and chipset components to
external monitoring or control devices. PECI is designed to support the
following sideband functions:
* Processor and DRAM thermal management
- Processor fan speed control is managed by comparing Digital Thermal
Sensor (DTS) thermal readings acquired via PECI against the
processor-specific fan speed control reference point, or TCONTROL.
Both TCONTROL and DTS thermal readings are accessible via the processor
PECI client. These variables are referenced to a common temperature,
the TCC activation point, and are both defined as negative offsets from
that reference.
- PECI based access to the processor package configuration space provides
a means for Baseboard Management Controllers (BMC) or other platform
management devices to actively manage the processor and memory power
and thermal features.
* Platform Manageability
- Platform manageability functions including thermal, power, and error
monitoring. Note that platform 'power' management includes monitoring
and control for both the processor and DRAM subsystem to assist with
data center power limiting.
- PECI allows read access to certain error registers in the processor MSR
space and status monitoring registers in the PCI configuration space
within the processor and downstream devices.
- PECI permits writes to certain registers in the processor PCI
configuration space.
* Processor Interface Tuning and Diagnostics
- Processor interface tuning and diagnostics capabilities
(Intel(c) Interconnect BIST). The processors Intel(c) Interconnect
Built In Self Test (Intel(c) IBIST) allows for infield diagnostic
capabilities in the Intel UPI and memory controller interfaces. PECI
provides a port to execute these diagnostics via its PCI Configuration
read and write capabilities.
* Failure Analysis
- Output the state of the processor after a failure for analysis via
Crashdump.
PECI uses a single wire for self-clocking and data transfer. The bus
requires no additional control lines. The physical layer is a self-clocked
one-wire bus that begins each bit with a driven, rising edge from an idle
level near zero volts. The duration of the signal driven high depends on
whether the bit value is a logic '0' or logic '1'. PECI also includes
variable data transfer rate established with every message. In this way,
it is highly flexible even though underlying logic is simple.
The interface design was optimized for interfacing to Intel processor and
chipset components in both single processor and multiple processor
environments. The single wire interface provides low board routing
overhead for the multiple load connections in the congested routing area
near the processor and chipset components. Bus speed, error checking, and
low protocol overhead provides adequate link bandwidth and reliability to
transfer critical device operating conditions and configuration
information.
This implementation provides the basic framework to add PECI extensions
to the Linux bus and device models. A hardware specific 'Adapter' driver
can be attached to the PECI bus to provide sideband functions described
above. It is also possible to access all devices on an adapter from
userspace through the /dev interface. A device specific 'Client' driver
also can be attached to the PECI bus so each processor client's features
can be supported by the 'Client' driver through an adapter connection in
the bus. This patch set includes Aspeed 24xx/25xx PECI driver and a generic
PECI hwmon driver as the first implementation for both adapter and client
drivers on the PECI bus framework.
v1 -> v2
- Additionally implemented a core driver to support PECI linux bus driver
model.
- Modified Aspeed PECI driver to make that to be an adapter driver in PECI
bus.
- Modified PECI hwmon driver to make that to be a client driver in PECI
bus.
- Simplified hwmon driver attribute labels and removed redundant strings.
- Removed core_nums from device tree setting of hwmon driver and modified
core number detection logic to check the resolved_core register in
client CPU's local PCI configuration area.
- Removed dimm_nums from device tree setting of hwmon driver and added
populated DIMM detection logic to support dynamic creation.
- Removed indexing gap on core temperature and DIMM temperature attributes.
- Improved hwmon registration and dynamic attribute creation logic.
- Fixed structure definitions in PECI uapi header to make that use __u8,
__u16 and etc.
- Modified wait_for_completion_interruptible_timeout error handling logic
in Aspeed PECI driver to deliver errors correctly.
- Removed low-level xfer command from ioctl and kept only high-level PECI
command suite as ioctls.
- Fixed I/O timeout logic in Aspeed PECI driver using ktime.
- Added a function into hwmon driver to simplify update delay checking.
- Added a function into hwmon driver to convert 10.6 to millidegree.
- Dropped non-standard attributes in hwmon driver.
- Fixed OF table for hwmon to make it indicate as a PECI client of Intel
CPU target.
- Added a maintainer of PECI subsystem into MAINTAINERS document.
Thanks,
-Jae
Jae Hyun Yoo (8):
drivers/peci: Add support for PECI bus driver core
Documentations: dt-bindings: Add a document of PECI adapter driver for
Aspeed AST24xx/25xx SoCs
ARM: dts: aspeed: peci: Add PECI node
drivers/peci: Add a PECI adapter driver for Aspeed AST24xx/AST25xx
Documentation: dt-bindings: Add a document for PECI hwmon client driver
Documentation: hwmon: Add a document for a PECI hwmon client driver
drivers/hwmon: Add a generic PECI hwmon client driver
Add a maintainer for the PECI subsystem
.../devicetree/bindings/hwmon/peci-hwmon.txt | 27 +
.../devicetree/bindings/peci/peci-aspeed.txt | 73 ++
Documentation/hwmon/peci-hwmon | 73 ++
MAINTAINERS | 9 +
arch/arm/boot/dts/aspeed-g4.dtsi | 25 +
arch/arm/boot/dts/aspeed-g5.dtsi | 25 +
drivers/Kconfig | 2 +
drivers/Makefile | 1 +
drivers/hwmon/Kconfig | 10 +
drivers/hwmon/Makefile | 1 +
drivers/hwmon/peci-hwmon.c | 928 ++++++++++++++
drivers/peci/Kconfig | 39 +
drivers/peci/Makefile | 9 +
drivers/peci/peci-aspeed.c | 510 ++++++++
drivers/peci/peci-core.c | 1337 ++++++++++++++++
include/linux/peci.h | 97 ++
include/uapi/linux/peci-ioctl.h | 207 +++
17 files changed, 3373 insertions(+)
create mode 100644 Documentation/devicetree/bindings/hwmon/peci-hwmon.txt
create mode 100644 Documentation/devicetree/bindings/peci/peci-aspeed.txt
create mode 100644 Documentation/hwmon/peci-hwmon
create mode 100644 drivers/hwmon/peci-hwmon.c
create mode 100644 drivers/peci/Kconfig
create mode 100644 drivers/peci/Makefile
create mode 100644 drivers/peci/peci-aspeed.c
create mode 100644 drivers/peci/peci-core.c
create mode 100644 include/linux/peci.h
create mode 100644 include/uapi/linux/peci-ioctl.h
--
2.16.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
