[PATCH 2/2] fpga: reset bridge: Add the reset bridge

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Adds the reset bridge. After the bitstream load the reset
bridge helps in reseting the programable logic. The
reset lines depends on the design.

Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xxxxxxxxxx>
---
 drivers/fpga/Kconfig             |   8 ++++
 drivers/fpga/Makefile            |   1 +
 drivers/fpga/xilinx-rst-bridge.c | 100 +++++++++++++++++++++++++++++++++++++++
 3 files changed, 109 insertions(+)
 create mode 100644 drivers/fpga/xilinx-rst-bridge.c

diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig
index ad5448f..752a907 100644
--- a/drivers/fpga/Kconfig
+++ b/drivers/fpga/Kconfig
@@ -117,4 +117,12 @@ config XILINX_PR_DECOUPLER
          region of the FPGA from the busses while that region is
          being reprogrammed during partial reconfig.

+config XILINX_RST_BRIDGE
+       tristate "Xilinx Reset bridge"
+       depends on FPGA_BRIDGE
+       help
+         Say Y to enable drivers for Xilinx Reset bridge.
+         After writing the bitstream there has to be a reset.
+         The reset lines are design specific.
+
 endif # FPGA
diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile
index f98dcf1..c1b0d13 100644
--- a/drivers/fpga/Makefile
+++ b/drivers/fpga/Makefile
@@ -23,6 +23,7 @@ obj-$(CONFIG_FPGA_BRIDGE)             += fpga-bridge.o
 obj-$(CONFIG_SOCFPGA_FPGA_BRIDGE)      += altera-hps2fpga.o altera-fpga2sdram.o
 obj-$(CONFIG_ALTERA_FREEZE_BRIDGE)     += altera-freeze-bridge.o
 obj-$(CONFIG_XILINX_PR_DECOUPLER)      += xilinx-pr-decoupler.o
+obj-$(CONFIG_FPGA_MGR_ZYNQMP_FPGA)     += xilinx-rst-bridge.o

 # High Level Interfaces
 obj-$(CONFIG_FPGA_REGION)              += fpga-region.o
diff --git a/drivers/fpga/xilinx-rst-bridge.c b/drivers/fpga/xilinx-rst-bridge.c
new file mode 100644
index 0000000..8062283
--- /dev/null
+++ b/drivers/fpga/xilinx-rst-bridge.c
@@ -0,0 +1,100 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx FPGA reset bridge.
+ * Copyright (c) 2018 Xilinx Inc.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/fpga/fpga-bridge.h>
+#include <linux/reset.h>
+
+struct xlnx_rst_bridge_priv {
+       struct device *dev;
+       bool enable;
+};
+
+static int xlnx_rst_bridge_enable_set(struct fpga_bridge *bridge, bool enable)
+{
+       struct xlnx_rst_bridge_priv *priv = bridge->priv;
+       struct device *dev = priv->dev;
+       struct reset_control *rstc;
+       int ret = 0;
+
+       if (enable) {
+               rstc = of_reset_control_array_get(dev->of_node, false, false);
+               if (IS_ERR(rstc))
+                       return PTR_ERR(rstc);
+
+               ret = reset_control_reset(rstc);
+
+               reset_control_put(rstc);
+
+               if (ret)
+                       dev_err(dev, "Reset failed\n");
+       } else {
+               dev_dbg(dev, "Bridge disabled\n");
+       }
+
+       if (!ret)
+               priv->enable = enable;
+
+       return ret;
+}
+
+static int xlnx_rst_bridge_enable_show(struct fpga_bridge *bridge)
+{
+       struct xlnx_rst_bridge_priv *priv = bridge->priv;
+
+       return priv->enable;
+}
+
+static struct fpga_bridge_ops xlnx_rst_bridge_ops = {
+       .enable_set = xlnx_rst_bridge_enable_set,
+       .enable_show = xlnx_rst_bridge_enable_show,
+};
+
+static int xlnx_rst_bridge_probe(struct platform_device *pdev)
+{
+       struct xlnx_rst_bridge_priv *priv;
+       struct device *dev = &pdev->dev;
+
+       priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+       if (!priv)
+               return -ENOMEM;
+
+       priv->dev = dev;
+
+       return fpga_bridge_register(dev, "xlnx_rst_bridge",
+                                   &xlnx_rst_bridge_ops, priv);
+}
+
+static int xlnx_rst_bridge_remove(struct platform_device *pdev)
+{
+       fpga_bridge_unregister(&pdev->dev);
+
+       return 0;
+}
+
+static const struct of_device_id xlnx_rst_bridge_of_match[] = {
+       { .compatible = "xlnx,rst-bridge", },
+       {},
+};
+MODULE_DEVICE_TABLE(of, xlnx_rst_bridge_of_match);
+
+static struct platform_driver xlnx_rst_bridge_driver = {
+       .probe = xlnx_rst_bridge_probe,
+       .remove = xlnx_rst_bridge_remove,
+       .driver = {
+               .name   = "xlnx_rst_bridge",
+               .of_match_table = of_match_ptr(xlnx_rst_bridge_of_match),
+       },
+};
+
+module_platform_driver(xlnx_rst_bridge_driver);
+
+MODULE_DESCRIPTION("Xilinx reset Bridge");
+MODULE_AUTHOR("Shubhrajyoti Datta <shubhrajyoti.datta@xxxxxxxxxx>");
+MODULE_LICENSE("GPL v2");
--
2.1.1

This email and any attachments are intended for the sole use of the named recipient(s) and contain(s) confidential information that may be proprietary, privileged or copyrighted under applicable law. If you are not the intended recipient, do not read, copy, or forward this email message or any attachments. Delete this email message and any attachments immediately.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux