Hi,
Thanks for the patch.
A few questions below.
On Thu, Jan 25, 2018 at 4:51 AM, Jolly Shah <jolly.shah@xxxxxxxxxx> wrote:
> This patch is adding communication layer with firmware.
> Firmware driver provides an interface to firmware APIs.
> Interface APIs can be used by any driver to communicate to
> PMUFW(Platform Management Unit). All requests go through ATF.
>
> Signed-off-by: Jolly Shah <jollys@xxxxxxxxxx>
> Signed-off-by: Rajan Vaja <rajanv@xxxxxxxxxx>
> ---
<snip>
>
> +/**
> + * zynqmp_pm_clock_enable - Enable the clock for given id
> + * @clock_id: ID of the clock to be enabled
Does it enable all the parents also if they are disabled?
> + *
> + * This function is used by master to enable the clock
> + * including peripherals and PLL clocks.
> + *
> + * Return: Returns status, either success or error+reason.
> + */
> +static int zynqmp_pm_clock_enable(u32 clock_id)
> +{
> + return invoke_pm_fn(PM_CLOCK_ENABLE, clock_id, 0, 0, 0, NULL);
> +}
> +
> +/**
> + * zynqmp_pm_clock_disable - Disable the clock for given id
> + * @clock_id: ID of the clock to be disable
> + *
> + * This function is used by master to disable the clock
> + * including peripherals and PLL clocks.
> + *
> + * Return: Returns status, either success or error+reason.
> + */
> +static int zynqmp_pm_clock_disable(u32 clock_id)
> +{
> + return invoke_pm_fn(PM_CLOCK_DISABLE, clock_id, 0, 0, 0, NULL);
> +}
> +
> +/**
> + * zynqmp_pm_clock_getstate - Get the clock state for given id
> + * @clock_id: ID of the clock to be queried
> + * @state: 1/0 (Enabled/Disabled)
> + *
> + * This function is used by master to get the state of clock
> + * including peripherals and PLL clocks.
> + *
> + * Return: Returns status, either success or error+reason.
> + */
> +static int zynqmp_pm_clock_getstate(u32 clock_id, u32 *state)
> +{
> + u32 ret_payload[PAYLOAD_ARG_CNT];
> + int ret;
> +
> + ret = invoke_pm_fn(PM_CLOCK_GETSTATE, clock_id, 0, 0, 0, ret_payload);
> + *state = ret_payload[1];
> +
> + return ret;
> +}
> +
> +/**
> + * zynqmp_pm_clock_setdivider - Set the clock divider for given id
> + * @clock_id: ID of the clock
> + * @div_type: TYPE_DIV1: div1
> + * TYPE_DIV2: div2
div type didnt see in the signature.
> + * @divider: divider value.
> + *
> + * This function is used by master to set divider for any clock
> + * to achieve desired rate.
> + *
> + * Return: Returns status, either success or error+reason.
> + */
> +static int zynqmp_pm_clock_setdivider(u32 clock_id, u32 divider)
> +{
> + return invoke_pm_fn(PM_CLOCK_SETDIVIDER, clock_id, divider, 0, 0, NULL);
> +}
> +
> +/**
> + * zynqmp_pm_clock_getdivider - Get the clock divider for given id
> + * @clock_id: ID of the clock
> + * @div_type: TYPE_DIV1: div1
> + * TYPE_DIV2: div2
didnt see this below.
> + * @divider: divider value.
> + *
> + * This function is used by master to get divider values
> + * for any clock.
> + *
> + * Return: Returns status, either success or error+reason.
> + */
> +static int zynqmp_pm_clock_getdivider(u32 clock_id, u32 *divider)
> +{
> + u32 ret_payload[PAYLOAD_ARG_CNT];
> + int ret;
> +
> + ret = invoke_pm_fn(PM_CLOCK_GETDIVIDER, clock_id, 0, 0, 0, ret_payload);
> + *divider = ret_payload[1];
> +
> + return ret;
> +}
> +
> +/**
> + * zynqmp_pm_clock_setrate - Set the clock rate for given id
> + * @clock_id: ID of the clock
> + * @rate: rate value in hz
> + *
> + * This function is used by master to set rate for any clock.
> + *
> + * Return: Returns status, either success or error+reason.
> + */
So this can set rate only 4G max ?
> +static int zynqmp_pm_clock_setrate(u32 clock_id, u32 rate)
> +{
> + return invoke_pm_fn(PM_CLOCK_SETRATE, clock_id, rate, 0, 0, NULL);
> +}
> +
> +/**
> + * zynqmp_pm_clock_getrate - Get the clock rate for given id
> + * @clock_id: ID of the clock
> + * @rate: rate value in hz
> + *
> + * This function is used by master to get rate
> + * for any clock.
> + *
> + * Return: Returns status, either success or error+reason.
> + */
Same question here?
> +static int zynqmp_pm_clock_getrate(u32 clock_id, u32 *rate)
> +{
> + u32 ret_payload[PAYLOAD_ARG_CNT];
> + int ret;
> +
> + ret = invoke_pm_fn(PM_CLOCK_GETRATE, clock_id, 0, 0, 0, ret_payload);
> + *rate = ret_payload[1];
> +
> + return ret;
> +}
> +
Also what is the difference between set rate and set divider?
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
