On Wed, 24 Jan 2018, Fabrice Gasnier wrote:
> On 01/23/2018 05:41 PM, Lee Jones wrote:
> > On Tue, 23 Jan 2018, Fabrice Gasnier wrote:
> >> On 01/23/2018 04:30 PM, Lee Jones wrote:
> >>> On Tue, 23 Jan 2018, Fabrice Gasnier wrote:
> >>>
> >>>> On 01/23/2018 02:32 PM, Lee Jones wrote:
> >>>>> On Tue, 16 Jan 2018, Fabrice Gasnier wrote:
> >>>>>
> >>>>>> STM32 Timers can support up to 7 dma requests:
> >>>>>> 4 channels, update, compare and trigger.
> >>>>>> Optionally request part, or all dmas from stm32-timers MFD core.
> >>>>>> Also, keep reference of device's bus address to allow child drivers to
> >>>>>> transfer data from/to device by using dma.
> >>>>>>
> >>>>>> Signed-off-by: Fabrice Gasnier <fabrice.gasnier@xxxxxx>
> >>>>>> ---
> >>>>>> drivers/mfd/stm32-timers.c | 37 ++++++++++++++++++++++++++++++++++++-
> >>>>>> include/linux/mfd/stm32-timers.h | 14 ++++++++++++++
> >>>>>> 2 files changed, 50 insertions(+), 1 deletion(-)
> >>>>>>
> >>>>>> diff --git a/drivers/mfd/stm32-timers.c b/drivers/mfd/stm32-timers.c
> >>>>>> static int stm32_timers_probe(struct platform_device *pdev)
> >>>>>> {
> >>>>>> struct device *dev = &pdev->dev;
> >>>>>> @@ -44,6 +61,7 @@ static int stm32_timers_probe(struct platform_device *pdev)
> >>>>>> mmio = devm_ioremap_resource(dev, res);
> >>>>>> if (IS_ERR(mmio))
> >>>>>> return PTR_ERR(mmio);
> >>>>>> + ddata->phys_base = res->start;
> >>>>>
> >>>>> What do you use this for?
> >>>>
> >>>> This is used in in child driver (pwm) for capture data transfer by dma.
> >>>
> >>> Might be worth being clear about that.
> >>>
> >>> Perhaps pass in 'dma_base' (phys_base + offset) instead?
> >>
> >> I guess you've had a look at [PATCH 5/8] pwm: stm32: add capture
> >> support. Are you talking about passing phys_base + TIM_DMAR ?
> >
> > I have and I am.
> >
> >> If this is the case, I'd prefer to keep phys base only if you don't
> >> mind, and handle TIM_DMAR offset in pwm driver. This way, all dma slave
> >> config is kept locally at one place.
> >> Or do you mean something else ?
> >>
> >> Maybe I can add a comment here about this ?
> >> Something like:
> >> /* phys_base to be used by child driver, e.g. DMA burst mode */
> >
> > I haven't seen the memory map for this device, so it's not easy for me
> > to comment, but passing in the physical address of the parent MFD into
> > a child device doesn't quite sit right with me.
> >
> > At what level does TIM_DMAR sit? Is it a child (PWM) specific
> > property, or is it described at parent (Timer) level?
> >
> Hi Lee,
>
> This isn't child (PWM) specific. TIM_DMAR is described at timer level as
> well as all timers DMA requests lines. Current patchset make it useful
> for PWM capture. Basically, I think this can be seen as interrupts, as
> each (0..7) dma request has an enable bit (in DIER: interrupt enable
> register). This is similar as interrupts at timer level.
>
> So, I understand your point regarding passing physical address of the
> parent MFD... Speaking of interrupts, I'd probably have looked at
> irq_chip. Regarding dma, i'm not sure what is preferred way ?
>
> Another way maybe to export a routine (export symbol) from MFD core, to
> handle dma transfer from there?
> By looking into drivers/mfd, I found similar approach, e.g.
> rtsx_pci_dma_transfer(). Do you think this is better approach ?
>
> Please let me know your opinion.
It sounds fine in principle. You are in a better position to make
that decision as you know the H/W more intimately than I, however it
does sound like a good idea to abstract the DMA handling from the
device if these aren't device-{level|specific} operations.
--
Lee Jones
Linaro Services Technical Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
