Hi Florian,
first of all, thank you for your answer.
On 02/10/2014 06:09 PM, Florian Fainelli wrote:
Hi Gerlando,
Le lundi 10 février 2014, 17:14:59 Gerlando Falauto a écrit :
Hi,
I'm currently trying to fix an issue for which this patch provides a
partial solution, so apologies in advance for jumping into the
discussion for my own purposes...
On 02/04/2014 09:39 PM, Florian Fainelli wrote:> 2014-01-17 Matthew
Garrett <matthew.garrett@xxxxxxxxxx>:
>> Some hardware may be broken in interesting and board-specific ways, such
>> that various bits of functionality don't work. This patch provides a
>> mechanism for overriding mii registers during init based on the
contents of
>> the device tree data, allowing board-specific fixups without having to
>> pollute generic code.
>
> It would be good to explain exactly how your hardware is broken
> exactly. I really do not think that such a fine-grained setting where
> you could disable, e.g: 100BaseT_Full, but allow 100BaseT_Half to
> remain usable makes that much sense. In general, Gigabit might be
> badly broken, but 100 and 10Mbits/sec should work fine. How about the
> MASTER-SLAVE bit, is overriding it really required?
>
> Is not a PHY fixup registered for a specific OUI the solution you are
> looking for? I am also concerned that this creates PHY troubleshooting
> issues much harder to debug than before as we may have no idea about
> how much information has been put in Device Tree to override that.
>
> Finally, how about making this more general just like the BCM87xx PHY
> driver, which is supplied value/reg pairs directly? There are 16
> common MII registers, and 16 others for vendor specific registers,
> this is just covering for about 2% of the possible changes.
Good point. That would easily help me with my current issue, which
requires autoneg to be disabled to begin with (by clearing BMCR_ANENABLE
from register 0).
Is there a point in time (e.g: after some specific initial configuration has
been made) where BMCR_ANENABLE can be used?
What do you mean? In my case, for some HW-related reason (due to the PHY
counterpart I guess) autoneg needs to be disabled.
This is currently done by the bootloader code (which clears the bit).
What I'm looking for is some way for the kernel to either reinforce this
setting, or just take that into account and skip autoneg.
On top of that, there's a HW errata about that particular PHY, which
requires certain operations to be performed on the PHY as a workaround
*WHEN AUTONEG IS DISABLED*. That I'd implement on a PHY-specif driver.
This would not however fix it entirely (I tried a quick hardwired
implementation), as the whole PHY machinery would not take that into
account and would re-enable autoneg anyway.
I also tried changing the patch so that phydev->support gets updated
There are multiple things that you could try doing here:
- override the PHY state machine in your read_status callback to make sure
that you always set phydev->autoneg set to AUTONEG_ENABLE
[you mean AUTONEG_DISABLE, right?]
Uhm, but I don't want to implement a driver for that PHY that always
disables autoneg. I only want to disable autoneg for that particular
board. I figure I might register a fixup for that board, but that kindof
makes everything more complicated and less clear. Plus, what should be
the criterion to determine whether we're running on that particular
hardware?
- clear the SUPPORTED_Autoneg bits from phydev->supported right after PHY
registration and before the call to phy_start()
I actually tried clearing it by tweaking the patch on this thread, but
the end result is that it does not produce any effect (see further
comments below). Only thing that seems to play a role here is explictly
setting phydev->autoneg = AUTONEG_DISABLE.
- set the PHY_HAS_MAGICANEG bit in your PHY driver flag
Again, this seems to play no role whatsoever here:
} else if (0 == phydev->link_timeout--) {
needs_aneg = 1;
/* If we have the magic_aneg bit,
* we try again */
if (phydev->drv->flags & PHY_HAS_MAGICANEG)
break;
}
break;
case PHY_NOLINK:
This code might have made sense when it was written in 2006 -- back
then, the break statement was skipping some fallback code. But now it
seems to do nothing.
(instead of phydev->advertising):
>> + if (!of_property_read_u32(np, override->prop, &tmp)) {
>> + if (tmp) {
>> + *val |= override->value;
>> + phydev->advertising |=
override->supported;
>> + } else {
>> + phydev->advertising &=
~(override->supported);
>> + }
>> +
>> + *mask |= override->value;
What I find weird is that the only way phydev->autoneg could ever be set
to disabled is from here (phy.c):
static void phy_sanitize_settings(struct phy_device *phydev)
{
u32 features = phydev->supported;
int idx;
/* Sanitize settings based on PHY capabilities */
if ((features & SUPPORTED_Autoneg) == 0)
phydev->autoneg = AUTONEG_DISABLE;
which is in turn only called when phydev->autoneg is set to
AUTONEG_DISABLE to begin with:
int phy_start_aneg(struct phy_device *phydev)
{
int err;
mutex_lock(&phydev->lock);
if (AUTONEG_DISABLE == phydev->autoneg)
phy_sanitize_settings(phydev);
So could someone please help me figure out what I'm missing here?
At first glance it looks like the PHY driver should be reading the phydev-
autoneg value when the PHY driver config_aneg() callback is called to be
allowed to set the forced speed and settings.
The way phy_sanitize_settings() is coded does not make it return a mask of
features, but only the forced supported speed and duplex. Then when the link
is forced but we are having some issues getting a link status, libphy tries
lower speeds and this function is used again to provide the next speed/duplex
pair to try.
What I was trying to say is that phy_sanitize_settings() is only called
when phydev->autoneg == AUTONEG_DISABLE, and in turn it's the only
generic function setting phydev->autoneg = AUTONEG_DISABLE.
So perhaps the condition should read:
- if (AUTONEG_DISABLE == phydev->autoneg)
+ if ((features & SUPPORTED_Autoneg) == 0)
phy_sanitize_settings(phydev);
Or else, some other parts of the generic code should take care of
setting it to AUTONEG_DISABLE, depending on whether the feature is
supported or not.
What I found weird is explicitly setting a value (phydev->autoneg =
AUTONEG_DISABLE), from a static function which is only called when that
condition is already true.
BTW, I feel like disabling autoneg from the start has never been a use
case before, am I right?
Thanks!
Gerlando
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
