Re: [PATCH v5 01/44] dt-bindings: clock: Add new bindings for TI Davinci PLL clocks

[David Lechner <david@xxxxxxxxxxxxxx>]

On 01/11/2018 03:34 PM, Adam Ford wrote:
> On Thu, Jan 11, 2018 at 3:04 PM, David Lechner <david@xxxxxxxxxxxxxx> wrote:
> > On 01/11/2018 02:58 PM, Adam Ford wrote:
> > > On Thu, Jan 11, 2018 at 2:04 PM, David Lechner <david@xxxxxxxxxxxxxx>
> > > wrote:
> > > > On 01/11/2018 12:50 PM, Adam Ford wrote:
> > > > > On Thu, Jan 11, 2018 at 12:29 PM, David Lechner <david@xxxxxxxxxxxxxx>
> > > > > wrote:
> > > > > > If removing the "clk_ignore_unused" option causes the board to not
> > > > > > boot,
> > > > > > then we still have problems that need to be fixed, so please also test
> > > > > > without this option.
> > > > >
> > > > >
> > > > >
> > > > > Without this option, it still does not boot.  Without device tree it
> > > > > hangs after:
> > > > >
> > > > > [snip]
> > > > >
> > > > > NET: Registered protocol family 17
> > > > > Loading compiled-in X.509 certificates
> > > > > console [netcon0] enabled
> > > > > netconsole: network logging started
> > > > > davinci_emac davinci_emac.1: using random MAC addr: 5e:38:1a:1f:4f:77
> > > > > mmc0: host does not support reading read-only switch, assuming
> > > > > write-enable
> > > > > hctosys: unable to open rtc device (rtc0)
> > > > > mmc0: new high speed SDHC card at address b368
> > > > >
> > > > >
> > > > > With device tree it hangs after:
> > > > >
> > > > > [snip]
> > > > > mmc0: host does not support reading read-only switch, assuming
> > > > > write-enable
> > > > > mmc0: new high speed SDHC card at address b368
> > > > > mmcblk0: mmc0:b368 00000 3.75 GiB
> > > > >     mmcblk0: p1 p2
> > > > > pca953x 0-0020: 0-0020 supply vcc not found, using dummy regulator
> > > > > pca953x 0-0020: failed reading register
> > > > > pca953x: probe of 0-0020 failed with error -121
> > > > > console [netcon0] enabled
> > > > > netconsole: network logging started
> > > > > davinci_emac 1e20000.ethernet: incompatible machine/device type for
> > > > > reading mac address
> > > > > hctosys: unable to open rtc device (rtc0)
> > > >
> > > > Please try this change:
> > > >
> > > > diff --git a/drivers/clk/davinci/psc-da850.c
> > > > b/drivers/clk/davinci/psc-da850.c
> > > > index 3fd6b49..a526cc2 100644
> > > > --- a/drivers/clk/davinci/psc-da850.c
> > > > +++ b/drivers/clk/davinci/psc-da850.c
> > > > @@ -17,7 +17,7 @@ static const struct davinci_psc_clk_info
> > > > da850_psc0_info[]
> > > > __initconst = {
> > > >           LPSC(0, 0, tpcc0, pll0_sysclk2, LPSC_ALWAYS_ENABLED),
> > > >           LPSC(1, 0, tptc0, pll0_sysclk2, LPSC_ALWAYS_ENABLED),
> > > >           LPSC(2, 0, tptc1, pll0_sysclk2, LPSC_ALWAYS_ENABLED),
> > > > -       LPSC(3, 0, aemif, pll0_sysclk3, 0),
> > > > +       LPSC(3, 0, aemif, pll0_sysclk3, LPSC_ALWAYS_ENABLED),
> > > >           LPSC(4, 0, spi0, pll0_sysclk2, 0),
> > > >           LPSC(5, 0, mmcsd0, pll0_sysclk2, 0),
> > > >           LPSC(6, 0, aintc, pll0_sysclk4, LPSC_ALWAYS_ENABLED),
> > > >
> > > >
> > > >
> > > > If that does not work, try adding LPSC_ALWAYS_ENABLED to all of the
> > > > clocks
> > > > in this file and then eliminate them one by one until you find which one
> > > > is
> > > > preventing boot.
> > > Unfortunately, that didn't work.  I switch all the entries in both
> > > tables that had a 0 to LPSC_ALWAYS_ENABLED, but no luck booting.
> > >
> > > > If it still does not boot, there is a similar DIVCLK_ALWAYS_ENABLED flag
> > > > in
> > > > drivers/clk/davinci/pll-da850.c that you can repeat the exercise with.
> > > > Add
> > > > DIVCLK_ALWAYS_ENABLED to all of the clocks there and then eliminate it
> > > > one
> > > > by one until you find the clock that is causing the problem.
> > >
> > >
> > > Still no good news.  I switched all the entries with a 0 to
> > > DIVCLK_ALWAYS_ENABLED and it still didn't finish booting.
> > >
> > > I wonder if Sekhar Nori might have some suggestions.  I didn't look at
> > > the code or try to understand it.  I just changed the settings.
> > > >
> >
> > Even if a clock had another flag besides zero, you will need to add
> > LPSC_ALWAYS_ENABLED by or-ing it with the other flag.
>
> [snip]
>
>
> Thanks for clarifying.  I was able to make it work with the following patch:
>
> diff --git a/drivers/clk/davinci/psc-da850.c b/drivers/clk/davinci/psc-da850.c
> index 3b4583d..a76b8682 100644
> --- a/drivers/clk/davinci/psc-da850.c
> +++ b/drivers/clk/davinci/psc-da850.c
> @@ -25,7 +25,7 @@ static const struct davinci_psc_clk_info
> da850_psc0_info[] __initconst = {
>          LPSC(9, 0, uart0, pll0_sysclk2, 0),
>          LPSC(13, 0, pruss, pll0_sysclk2, 0),
>          LPSC(14, 0, arm, pll0_sysclk6, LPSC_ALWAYS_ENABLED),
> -       LPSC(15, 1, dsp, pll0_sysclk1, LPSC_FORCE | LPSC_LOCAL_RESET),
> +       LPSC(15, 1, dsp, pll0_sysclk1, LPSC_FORCE | LPSC_LOCAL_RESET |
> LPSC_ALWAYS_ENABLED),
>          { }
>   };
>
>
> If you have an updated patch series with those two fixes, I add my
> name to the tested-by list.
>
>
> >
> [snip]
> >

Great! Thanks again for testing.

Sekhar, have you had a chance to look at the rest of the patches in the
series?

I'll wait a bit before I send a v6 to see if any other comments come.

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html