On Wed, 2017-12-27 at 12:45 -0600, Bjorn Helgaas wrote:
> On Wed, Dec 27, 2017 at 08:59:54AM +0800, honghui.zhang@xxxxxxxxxxxx wrote:
> > From: Honghui Zhang <honghui.zhang@xxxxxxxxxxxx>
> >
> > The hardware default value of IDs and class type is not correct,
> > fix that by setup the correct values before start up.
> >
> > Signed-off-by: Honghui Zhang <honghui.zhang@xxxxxxxxxxxx>
> > ---
> > drivers/pci/host/pcie-mediatek.c | 12 ++++++++++++
> > include/linux/pci_ids.h | 2 ++
> > 2 files changed, 14 insertions(+)
> >
> > diff --git a/drivers/pci/host/pcie-mediatek.c b/drivers/pci/host/pcie-mediatek.c
> > index fc29a9a..62aac0ea 100644
> > --- a/drivers/pci/host/pcie-mediatek.c
> > +++ b/drivers/pci/host/pcie-mediatek.c
> > @@ -74,6 +74,10 @@
> >
> > /* PCIe V2 per-port registers */
> > #define PCIE_MSI_VECTOR 0x0c0
> > +
> > +#define PCIE_CONF_ID 0x100
> > +#define PCIE_CONF_CLASS 0x104
> > +
> > #define PCIE_INT_MASK 0x420
> > #define INTX_MASK GENMASK(19, 16)
> > #define INTX_SHIFT 16
> > @@ -393,6 +397,14 @@ static int mtk_pcie_startup_port_v2(struct mtk_pcie_port *port)
> > val |= PCIE_CSR_LTSSM_EN(port->slot) |
> > PCIE_CSR_ASPM_L1_EN(port->slot);
> > writel(val, pcie->base + PCIE_SYS_CFG_V2);
> > +
> > + /* Set up vendor ID and device ID for MT7622*/
> > + val = PCI_VENDOR_ID_MEDIATEK;
> > + writel(val, port->base + PCIE_CONF_ID);
> > +
> > + /* Set up class code for MT7622 */
> > + val = PCI_CLASS_BRIDGE_PCI << 16;
> > + writel(val, port->base + PCIE_CONF_CLASS);
>
> 1) Your comments mention MT7622 specifically, but this code is run for
> both mt2712-pcie and mt7622-pcie. If this code is safe and necessary
> for both mt2712-pcie and mt7622-pcie, please remove the mention of
> MT7622.
Hmm, the code snippet added here will only be executed by MT7622, since
MT2712 will not enter this "if (pcie->base) {" condition.
Should the mention of MT7622 must be removed in this case?
>
> 2) The first comment mentions both "vendor ID and device ID" but you
> don't write the device ID. Since this code applies to both
> mt2712-pcie and mt7622-pcie, my guess is that you don't *want* to
> write the device ID. If that's the case, please fix the comment.
>
My bad, I did not check the comments carefully.
Thanks.
> 3) If you only need to set the vendor ID, you're performing a 32-bit
> write (writel()) to update a 16-bit value. Please use writew()
> instead.
>
Ok, thanks, I guess I could use the following code snippet in the next
version:
val = readl(port->base + PCIE_CONF_VENDOR_ID)
val &= ~GENMASK(15, 0);
val |= PCI_VENDOR_ID_MEDIATEK;
writel(val, port->base + PCIE_CONF_VENDOR_ID);
> 4) If you only need to set the vendor ID, please use a definition like
> "PCIE_CONF_VENDOR_ID" instead of the ambiguous "PCIE_CONF_ID".
>
> 5) If you only need to set the vendor ID, please update the changelog
> to mention "vendor ID" specifically instead of the ambiguous "IDs".
> 6) Please add a space before the closing "*/" of the first comment.
>
> 7) PCI_CLASS_BRIDGE_PCI is for a PCI-to-PCI bridge, i.e., one that has
> PCI on both the primary (upstream) side and the secondary (downstream)
> side. That kind of bridge has a type 1 config header (see
> PCI_HEADER_TYPE) and the PCI_PRIMARY_BUS and PCI_SECONDARY_BUS
> registers tell us the bus number of the primary and secondary sides.
>
> I don't believe this device is a PCI-to-PCI bridge. I think it's a
> *host* bridge that has some non-PCI interface on the upstream side and
> should have a type 0 config header. If that's the case you should use
> PCI_CLASS_BRIDGE_HOST instead.
>
Thanks very much for your help with the review, I will fix the other
issue in the next version.
> > }
> >
> > /* Assert all reset signals */
> > diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h
> > index ab20dc5..2480b0e 100644
> > --- a/include/linux/pci_ids.h
> > +++ b/include/linux/pci_ids.h
> > @@ -2113,6 +2113,8 @@
> >
> > #define PCI_VENDOR_ID_MYRICOM 0x14c1
> >
> > +#define PCI_VENDOR_ID_MEDIATEK 0x14c3
> > +
> > #define PCI_VENDOR_ID_TITAN 0x14D2
> > #define PCI_DEVICE_ID_TITAN_010L 0x8001
> > #define PCI_DEVICE_ID_TITAN_100L 0x8010
> > --
> > 2.6.4
> >
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
