On Wed, Dec 27, 2017 at 08:59:54AM +0800, honghui.zhang@xxxxxxxxxxxx wrote: > From: Honghui Zhang <honghui.zhang@xxxxxxxxxxxx> > > The hardware default value of IDs and class type is not correct, > fix that by setup the correct values before start up. > > Signed-off-by: Honghui Zhang <honghui.zhang@xxxxxxxxxxxx> > --- > drivers/pci/host/pcie-mediatek.c | 12 ++++++++++++ > include/linux/pci_ids.h | 2 ++ > 2 files changed, 14 insertions(+) > > diff --git a/drivers/pci/host/pcie-mediatek.c b/drivers/pci/host/pcie-mediatek.c > index fc29a9a..62aac0ea 100644 > --- a/drivers/pci/host/pcie-mediatek.c > +++ b/drivers/pci/host/pcie-mediatek.c > @@ -74,6 +74,10 @@ > > /* PCIe V2 per-port registers */ > #define PCIE_MSI_VECTOR 0x0c0 > + > +#define PCIE_CONF_ID 0x100 > +#define PCIE_CONF_CLASS 0x104 > + > #define PCIE_INT_MASK 0x420 > #define INTX_MASK GENMASK(19, 16) > #define INTX_SHIFT 16 > @@ -393,6 +397,14 @@ static int mtk_pcie_startup_port_v2(struct mtk_pcie_port *port) > val |= PCIE_CSR_LTSSM_EN(port->slot) | > PCIE_CSR_ASPM_L1_EN(port->slot); > writel(val, pcie->base + PCIE_SYS_CFG_V2); > + > + /* Set up vendor ID and device ID for MT7622*/ > + val = PCI_VENDOR_ID_MEDIATEK; > + writel(val, port->base + PCIE_CONF_ID); > + > + /* Set up class code for MT7622 */ > + val = PCI_CLASS_BRIDGE_PCI << 16; > + writel(val, port->base + PCIE_CONF_CLASS); 1) Your comments mention MT7622 specifically, but this code is run for both mt2712-pcie and mt7622-pcie. If this code is safe and necessary for both mt2712-pcie and mt7622-pcie, please remove the mention of MT7622. 2) The first comment mentions both "vendor ID and device ID" but you don't write the device ID. Since this code applies to both mt2712-pcie and mt7622-pcie, my guess is that you don't *want* to write the device ID. If that's the case, please fix the comment. 3) If you only need to set the vendor ID, you're performing a 32-bit write (writel()) to update a 16-bit value. Please use writew() instead. 4) If you only need to set the vendor ID, please use a definition like "PCIE_CONF_VENDOR_ID" instead of the ambiguous "PCIE_CONF_ID". 5) If you only need to set the vendor ID, please update the changelog to mention "vendor ID" specifically instead of the ambiguous "IDs". 6) Please add a space before the closing "*/" of the first comment. 7) PCI_CLASS_BRIDGE_PCI is for a PCI-to-PCI bridge, i.e., one that has PCI on both the primary (upstream) side and the secondary (downstream) side. That kind of bridge has a type 1 config header (see PCI_HEADER_TYPE) and the PCI_PRIMARY_BUS and PCI_SECONDARY_BUS registers tell us the bus number of the primary and secondary sides. I don't believe this device is a PCI-to-PCI bridge. I think it's a *host* bridge that has some non-PCI interface on the upstream side and should have a type 0 config header. If that's the case you should use PCI_CLASS_BRIDGE_HOST instead. > } > > /* Assert all reset signals */ > diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h > index ab20dc5..2480b0e 100644 > --- a/include/linux/pci_ids.h > +++ b/include/linux/pci_ids.h > @@ -2113,6 +2113,8 @@ > > #define PCI_VENDOR_ID_MYRICOM 0x14c1 > > +#define PCI_VENDOR_ID_MEDIATEK 0x14c3 > + > #define PCI_VENDOR_ID_TITAN 0x14D2 > #define PCI_DEVICE_ID_TITAN_010L 0x8001 > #define PCI_DEVICE_ID_TITAN_100L 0x8010 > -- > 2.6.4 > -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
