DRA72 uses USB3 PHY for the 2nd lane of PCIE. The configuration
required to make USB3 PHY used for the 2nd lane of PCIe is done
here.
Signed-off-by: Kishon Vijay Abraham I <kishon@xxxxxx>
---
drivers/phy/ti/phy-ti-pipe3.c | 47 +++++++++++++++++++++++++++++++++++++------
1 file changed, 41 insertions(+), 6 deletions(-)
diff --git a/drivers/phy/ti/phy-ti-pipe3.c b/drivers/phy/ti/phy-ti-pipe3.c
index 68ce4a082b9b..d5a7cc435fb7 100644
--- a/drivers/phy/ti/phy-ti-pipe3.c
+++ b/drivers/phy/ti/phy-ti-pipe3.c
@@ -56,6 +56,12 @@
#define SATA_PLL_SOFT_RESET BIT(18)
+#define PHY_RX_ANA_PRGRAMMABILITY_REG 0xC
+#define MEM_EN_PLLBYP BIT(7)
+
+#define PHY_TX_TEST_CONFIG 0x2C
+#define MEM_ENTESTCLK BIT(31)
+
#define PIPE3_PHY_PWRCTL_CLK_CMD_MASK 0x003FC000
#define PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT 14
@@ -110,6 +116,10 @@
#define PLL_IDLE_TIME 100 /* in milliseconds */
#define PLL_LOCK_TIME 100 /* in milliseconds */
+#define PIPE3_PHY_DISABLE_SYNC_POWER BIT(4)
+
+#define CONFIGURE_AS_PCIE BIT(0)
+
struct pipe3_dpll_params {
u16 m;
u8 n;
@@ -141,6 +151,7 @@ struct ti_pipe3 {
unsigned int power_reg; /* power reg. index within syscon */
unsigned int pcie_pcs_reg; /* pcs reg. index in syscon */
bool sata_refclk_enabled;
+ u32 flags;
};
static struct pipe3_dpll_map dpll_map_usb[] = {
@@ -233,11 +244,22 @@ static int ti_pipe3_power_on(struct phy *x)
rate = rate / 1000000;
mask = OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_CMD_MASK |
OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_FREQ_MASK;
- val = PIPE3_PHY_TX_RX_POWERON << PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT;
+ val = PIPE3_PHY_TX_RX_POWERON;
+ if (phy->flags & CONFIGURE_AS_PCIE)
+ val |= PIPE3_PHY_DISABLE_SYNC_POWER;
+ val <<= PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT;
val |= rate << OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_FREQ_SHIFT;
ret = regmap_update_bits(phy->phy_power_syscon, phy->power_reg,
mask, val);
+
+ if (phy->flags & CONFIGURE_AS_PCIE) {
+ ret = regmap_update_bits(phy->phy_power_syscon, phy->power_reg,
+ mask, val);
+ if (ret < 0)
+ return ret;
+ }
+
return ret;
}
@@ -335,6 +357,19 @@ static int ti_pipe3_init(struct phy *x)
int ret = 0;
ti_pipe3_enable_clocks(phy);
+
+ if (phy->flags & CONFIGURE_AS_PCIE) {
+ val = ti_pipe3_readl(phy->phy_rx,
+ PHY_RX_ANA_PRGRAMMABILITY_REG);
+ val |= MEM_EN_PLLBYP;
+ ti_pipe3_writel(phy->phy_rx, PHY_RX_ANA_PRGRAMMABILITY_REG,
+ val);
+ val = ti_pipe3_readl(phy->phy_tx, PHY_TX_TEST_CONFIG);
+ val |= MEM_ENTESTCLK;
+ ti_pipe3_writel(phy->phy_tx, PHY_TX_TEST_CONFIG, val);
+ return 0;
+ }
+
/*
* Set pcie_pcs register to 0x96 for proper functioning of phy
* as recommended in AM572x TRM SPRUHZ6, section 18.5.2.2, table
@@ -395,7 +430,8 @@ static int ti_pipe3_exit(struct phy *x)
return 0;
/* PCIe doesn't have internal DPLL */
- if (!of_device_is_compatible(phy->dev->of_node, "ti,phy-pipe3-pcie")) {
+ if (!of_device_is_compatible(phy->dev->of_node, "ti,phy-pipe3-pcie") &&
+ !(phy->flags & CONFIGURE_AS_PCIE)) {
/* Put DPLL in IDLE mode */
val = ti_pipe3_readl(phy->pll_ctrl_base, PLL_CONFIGURATION2);
val |= PLL_IDLE;
@@ -589,12 +625,8 @@ static int ti_pipe3_get_tx_rx_base(struct ti_pipe3 *phy)
{
struct resource *res;
struct device *dev = phy->dev;
- struct device_node *node = dev->of_node;
struct platform_device *pdev = to_platform_device(dev);
- if (!of_device_is_compatible(node, "ti,phy-pipe3-pcie"))
- return 0;
-
res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
"phy_rx");
phy->phy_rx = devm_ioremap_resource(dev, res);
@@ -666,6 +698,9 @@ static int ti_pipe3_probe(struct platform_device *pdev)
if (ret)
return ret;
+ if (of_property_read_bool(node, "ti,configure-as-pcie"))
+ phy->flags |= CONFIGURE_AS_PCIE;
+
platform_set_drvdata(pdev, phy);
pm_runtime_enable(dev);
--
2.11.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
