Cc: Rob Herring <robh@xxxxxxxxxx>
Acked-by: Sakari Ailus <sakari.ailus@xxxxxxxxxxxxxxx>
Signed-off-by: Tim Harvey <tharvey@xxxxxxxxxxxxx>
---
v5:
- added Sakari's ack
v4:
- move include/dt-bindings/media/tda1997x.h to bindings patch
- clarify port node details
v3:
- fix typo
v2:
- add vendor prefix and remove _ from vidout-portcfg
- remove _ from labels
- remove max-pixel-rate property
- describe and provide example for single output port
- update to new audio port bindings
---
.../devicetree/bindings/media/i2c/tda1997x.txt | 179 +++++++++++++++++++++
include/dt-bindings/media/tda1997x.h | 78 +++++++++
2 files changed, 257 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/i2c/tda1997x.txt
create mode 100644 include/dt-bindings/media/tda1997x.h
diff --git a/Documentation/devicetree/bindings/media/i2c/tda1997x.txt b/Documentation/devicetree/bindings/media/i2c/tda1997x.txt
new file mode 100644
index 0000000..9ab53c3
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/tda1997x.txt
@@ -0,0 +1,179 @@
+Device-Tree bindings for the NXP TDA1997x HDMI receiver
+
+The TDA19971/73 are HDMI video receivers.
+
+The TDA19971 Video port output pins can be used as follows:
+ - RGB 8bit per color (24 bits total): R[11:4] B[11:4] G[11:4]
+ - YUV444 8bit per color (24 bits total): Y[11:4] Cr[11:4] Cb[11:4]
+ - YUV422 semi-planar 8bit per component (16 bits total): Y[11:4] CbCr[11:4]
+ - YUV422 semi-planar 10bit per component (20 bits total): Y[11:2] CbCr[11:2]
+ - YUV422 semi-planar 12bit per component (24 bits total): - Y[11:0] CbCr[11:0]
+ - YUV422 BT656 8bit per component (8 bits total): YCbCr[11:4] (2-cycles)
+ - YUV422 BT656 10bit per component (10 bits total): YCbCr[11:2] (2-cycles)
+ - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles)
+
+The TDA19973 Video port output pins can be used as follows:
+ - RGB 12bit per color (36 bits total): R[11:0] B[11:0] G[11:0]
+ - YUV444 12bit per color (36 bits total): Y[11:0] Cb[11:0] Cr[11:0]
+ - YUV422 semi-planar 12bit per component (24 bits total): Y[11:0] CbCr[11:0]
+ - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles)
+
+The Video port output pins are mapped via 4-bit 'pin groups' allowing
+for a variety of connection possibilities including swapping pin order within
+pin groups. The video_portcfg device-tree property consists of register mapping
+pairs which map a chip-specific VP output register to a 4-bit pin group. If
+the pin group needs to be bit-swapped you can use the *_S pin-group defines.
+
+Required Properties:
+ - compatible :
+ - "nxp,tda19971" for the TDA19971
+ - "nxp,tda19973" for the TDA19973
+ - reg : I2C slave address
+ - interrupts : The interrupt number
+ - DOVDD-supply : Digital I/O supply
+ - DVDD-supply : Digital Core supply
+ - AVDD-supply : Analog supply
+ - nxp,vidout-portcfg : array of pairs mapping VP output pins to pin groups.
+
+Optional Properties:
+ - nxp,audout-format : DAI bus format: "i2s" or "spdif".
+ - nxp,audout-width : width of audio output data bus (1-4).
+ - nxp,audout-layout : data layout (0=AP0 used, 1=AP0/AP1/AP2/AP3 used).
+ - nxp,audout-mclk-fs : Multiplication factor between stream rate and codec
+ mclk.
+
+The port node shall contain one endpoint child node for its digital
+output video port, in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Optional Endpoint Properties:
+ The following three properties are defined in video-interfaces.txt and
+ are valid for the output parallel bus endpoint:
+ - hsync-active: Horizontal synchronization polarity. Defaults to active high.
+ - vsync-active: Vertical synchronization polarity. Defaults to active high.
+ - data-active: Data polarity. Defaults to active high.
+
+Examples:
+ - VP[15:0] connected to IMX6 CSI_DATA[19:4] for 16bit YUV422
+ 16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins)
+ hdmi-receiver@48 {
+ compatible = "nxp,tda19971";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_tda1997x>;
+ reg = <0x48>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+ DOVDD-supply = <®_3p3v>;
+ AVDD-supply = <®_1p8v>;
+ DVDD-supply = <®_1p8v>;
+ /* audio */
+ #sound-dai-cells = <0>;
+ nxp,audout-format = "i2s";
+ nxp,audout-layout = <0>;
+ nxp,audout-width = <16>;
+ nxp,audout-mclk-fs = <128>;
+ /*
+ * The 8bpp YUV422 semi-planar mode outputs CbCr[11:4]
+ * and Y[11:4] across 16bits in the same pixclk cycle.
+ */
+ nxp,vidout-portcfg =
+ /* Y[11:8]<->VP[15:12]<->CSI_DATA[19:16] */
+ < TDA1997X_VP24_V15_12 TDA1997X_G_Y_11_8 >,
+ /* Y[7:4]<->VP[11:08]<->CSI_DATA[15:12] */
+ < TDA1997X_VP24_V11_08 TDA1997X_G_Y_7_4 >,
+ /* CbCc[11:8]<->VP[07:04]<->CSI_DATA[11:8] */
+ < TDA1997X_VP24_V07_04 TDA1997X_R_CR_CBCR_11_8 >,
+ /* CbCr[7:4]<->VP[03:00]<->CSI_DATA[7:4] */
+ < TDA1997X_VP24_V03_00 TDA1997X_R_CR_CBCR_7_4 >;
+
+ port {
+ tda1997x_to_ipu1_csi0_mux: endpoint {
+ remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+ bus-width = <16>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ data-active = <1>;
+ };
+ };
+ };
+ - VP[15:8] connected to IMX6 CSI_DATA[19:12] for 8bit BT656
+ 16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins)
+ hdmi-receiver@48 {
+ compatible = "nxp,tda19971";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_tda1997x>;
+ reg = <0x48>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+ DOVDD-supply = <®_3p3v>;
+ AVDD-supply = <®_1p8v>;
+ DVDD-supply = <®_1p8v>;
+ /* audio */
+ #sound-dai-cells = <0>;
+ nxp,audout-format = "i2s";
+ nxp,audout-layout = <0>;
+ nxp,audout-width = <16>;
+ nxp,audout-mclk-fs = <128>;
+ /*
+ * The 8bpp YUV422 semi-planar mode outputs CbCr[11:4]
+ * and Y[11:4] across 16bits in the same pixclk cycle.
+ */
+ nxp,vidout-portcfg =
+ /* Y[11:8]<->VP[15:12]<->CSI_DATA[19:16] */
+ < TDA1997X_VP24_V15_12 TDA1997X_G_Y_11_8 >,
+ /* Y[7:4]<->VP[11:08]<->CSI_DATA[15:12] */
+ < TDA1997X_VP24_V11_08 TDA1997X_G_Y_7_4 >,
+ /* CbCc[11:8]<->VP[07:04]<->CSI_DATA[11:8] */
+ < TDA1997X_VP24_V07_04 TDA1997X_R_CR_CBCR_11_8 >,
+ /* CbCr[7:4]<->VP[03:00]<->CSI_DATA[7:4] */
+ < TDA1997X_VP24_V03_00 TDA1997X_R_CR_CBCR_7_4 >;
+
+ port {
+ tda1997x_to_ipu1_csi0_mux: endpoint {
+ remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+ bus-width = <16>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ data-active = <1>;
+ };
+ };
+ };
+ - VP[15:8] connected to IMX6 CSI_DATA[19:12] for 8bit BT656
+ 16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins)
+ hdmi-receiver@48 {
+ compatible = "nxp,tda19971";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_tda1997x>;
+ reg = <0x48>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+ DOVDD-supply = <®_3p3v>;
+ AVDD-supply = <®_1p8v>;
+ DVDD-supply = <®_1p8v>;
+ /* audio */
+ #sound-dai-cells = <0>;
+ nxp,audout-format = "i2s";
+ nxp,audout-layout = <0>;
+ nxp,audout-width = <16>;
+ nxp,audout-mclk-fs = <128>;
+ /*
+ * The 8bpp BT656 mode outputs YCbCr[11:4] across 8bits over
+ * 2 pixclk cycles.
+ */
+ nxp,vidout-portcfg =
+ /* YCbCr[11:8]<->VP[15:12]<->CSI_DATA[19:16] */
+ < TDA1997X_VP24_V15_12 TDA1997X_R_CR_CBCR_11_8 >,
+ /* YCbCr[7:4]<->VP[11:08]<->CSI_DATA[15:12] */
+ < TDA1997X_VP24_V11_08 TDA1997X_R_CR_CBCR_7_4 >,
+
+ port {
+ tda1997x_to_ipu1_csi0_mux: endpoint {
+ remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+ bus-width = <16>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ data-active = <1>;
+ };
+ };
+ };
+
diff --git a/include/dt-bindings/media/tda1997x.h b/include/dt-bindings/media/tda1997x.h
new file mode 100644
index 0000000..f4cdf87
--- /dev/null
+++ b/include/dt-bindings/media/tda1997x.h
@@ -0,0 +1,78 @@
+/*
+ * Copyright (C) 2017 Gateworks Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#ifndef _DT_BINDINGS_MEDIA_TDA1997X_H
+#define _DT_BINDINGS_MEDIA_TDA1997X_H
+
+/* TDA19973 36bit Video Port control registers */
+#define TDA1997X_VP36_35_32 0
+#define TDA1997X_VP36_31_28 1
+#define TDA1997X_VP36_27_24 2
+#define TDA1997X_VP36_23_20 3
+#define TDA1997X_VP36_19_16 4
+#define TDA1997X_VP36_15_12 5
+#define TDA1997X_VP36_11_08 6
+#define TDA1997X_VP36_07_04 7
+#define TDA1997X_VP36_03_00 8
+
+/* TDA19971 24bit Video Port control registers */
+#define TDA1997X_VP24_V23_20 0
+#define TDA1997X_VP24_V19_16 1
+#define TDA1997X_VP24_V15_12 3
+#define TDA1997X_VP24_V11_08 4
+#define TDA1997X_VP24_V07_04 6
+#define TDA1997X_VP24_V03_00 7
+
+/* Pin groups */
+#define TDA1997X_VP_OUT_EN 0x80 /* enable output group */
+#define TDA1997X_VP_HIZ 0x40 /* hi-Z output group when not used */
+#define TDA1997X_VP_SWP 0x10 /* pin-swap output group */
+#define TDA1997X_R_CR_CBCR_3_0 (0 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ)
+#define TDA1997X_R_CR_CBCR_7_4 (1 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ)
+#define TDA1997X_R_CR_CBCR_11_8 (2 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ)
+#define TDA1997X_B_CB_3_0 (3 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ)
+#define TDA1997X_B_CB_7_4 (4 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ)
+#define TDA1997X_B_CB_11_8 (5 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ)
+#define TDA1997X_G_Y_3_0 (6 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ)
+#define TDA1997X_G_Y_7_4 (7 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ)
+#define TDA1997X_G_Y_11_8 (8 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ)
+/* pinswapped groups */
+#define TDA1997X_R_CR_CBCR_3_0_S (TDA1997X_R_CR_CBCR_3_0 | TDA1997X_VP_SWAP)
+#define TDA1997X_R_CR_CBCR_7_4_S (TDA1997X_R_CR_CBCR_7_4 | TDA1997X_VP_SWAP)
+#define TDA1997X_R_CR_CBCR_11_8_S (TDA1997X_R_CR_CBCR_11_8 | TDA1997X_VP_SWAP)
+#define TDA1997X_B_CB_3_0_S (TDA1997X_B_CB_3_0 | TDA1997X_VP_SWAP)
+#define TDA1997X_B_CB_7_4_S (TDA1997X_B_CB_7_4 | TDA1997X_VP_SWAP)
+#define TDA1997X_B_CB_11_8_S (TDA1997X_B_CB_11_8 | TDA1997X_VP_SWAP)
+#define TDA1997X_G_Y_3_0_S (TDA1997X_G_Y_3_0 | TDA1997X_VP_SWAP)
+#define TDA1997X_G_Y_7_4_S (TDA1997X_G_Y_7_4 | TDA1997X_VP_SWAP)
+#define TDA1997X_G_Y_11_8_S (TDA1997X_G_Y_11_8 | TDA1997X_VP_SWAP)
+
+/* Audio bus DAI format */
+#define TDA1997X_I2S16 1 /* I2S 16bit */
+#define TDA1997X_I2S32 2 /* I2S 32bit */
+#define TDA1997X_SPDIF 3 /* SPDIF */
+#define TDA1997X_OBA 4 /* One Bit Audio */
+#define TDA1997X_DST 5 /* Direct Stream Transfer */
+#define TDA1997X_I2S16_HBR 6 /* HBR straight in I2S 16bit mode */
+#define TDA1997X_I2S16_HBR_DEMUX 7 /* HBR demux in I2S 16bit mode */
+#define TDA1997X_I2S32_HBR_DEMUX 8 /* HBR demux in I2S 32bit mode */
+#define TDA1997X_SPDIF_HBR_DEMUX 9 /* HBR demux in SPDIF mode */
+
+/* Audio bus channel layout */
+#define TDA1997X_LAYOUT0 0 /* 2-channel */
+#define TDA1997X_LAYOUT1 1 /* 8-channel */
+
+/* Audio bus clock */
+#define TDA1997X_ACLK_16FS 0
+#define TDA1997X_ACLK_32FS 1
+#define TDA1997X_ACLK_64FS 2
+#define TDA1997X_ACLK_128FS 3
+#define TDA1997X_ACLK_256FS 4
+#define TDA1997X_ACLK_512FS 5
+
+#endif /* _DT_BINDINGS_MEDIA_TDA1997X_H */
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
