The ti-sysc binding does not yet describe the capabilities of the interconnect target module. So to make the ti-sysc binding usable for configuring the interconnect target module, we need to add few more properties: 1. To detect between omap2 and omap4 timers, let's add compatibles for them for "ti,sysc-omap2-timer" and,sysc-omap4-timer". This makes it easier to pick up the already initialized system timers later on 2. Let's add "ti,sysc-mask" for a mask of features supported by the interconnect target module. This describes what we have available in the various SYSCONFIG registers 3. Let's add "ti,sysc-midle" and "ti,sysc-sidle" lists for the master and slave idle modes supported by the interconnect target module. These describe the values available for MIDLE and SIDLE bits in the SYSCONFIG registers 4. Some interconnect target modules need a short delay after reset before they can be accessed, let's use "ti,sysc-delay-us" for that 5. Let's add "ti,syss-mask" bit to describe the optional SYSSTATUS register bits for reset done bits 6. Let's support the two existing custom quirk properties already listed in Documentation/devicetree/bindings/arm/omap/omap.txt for "ti,no-reset-on-init" and "ti,no-idle-on-init" 7. And finally, let's add a header for the binding for the dts files and the driver to use Cc: Benoît Cousson <bcousson@xxxxxxxxxxxx> Cc: Dave Gerlach <d-gerlach@xxxxxx> Cc: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx> Cc: Liam Girdwood <lgirdwood@xxxxxxxxx> Cc: Mark Brown <broonie@xxxxxxxxxx> Cc: Mark Rutland <mark.rutland@xxxxxxx> Cc: Mauro Carvalho Chehab <mchehab@xxxxxxxxxx> Cc: Nishanth Menon <nm@xxxxxx> Cc: Matthijs van Duin <matthijsvanduin@xxxxxxxxx> Cc: Paul Walmsley <paul@xxxxxxxxx> Cc: Peter Ujfalusi <peter.ujfalusi@xxxxxx> Cc: Sakari Ailus <sakari.ailus@xxxxxx> Cc: Suman Anna <s-anna@xxxxxx> Cc: Tero Kristo <t-kristo@xxxxxx> Cc: Tomi Valkeinen <tomi.valkeinen@xxxxxx> Signed-off-by: Tony Lindgren <tony@xxxxxxxxxxx> --- Documentation/devicetree/bindings/bus/ti-sysc.txt | 36 +++++++++++++++++++++++ include/dt-bindings/bus/ti-sysc.h | 22 ++++++++++++++ 2 files changed, 58 insertions(+) create mode 100644 include/dt-bindings/bus/ti-sysc.h diff --git a/Documentation/devicetree/bindings/bus/ti-sysc.txt b/Documentation/devicetree/bindings/bus/ti-sysc.txt --- a/Documentation/devicetree/bindings/bus/ti-sysc.txt +++ b/Documentation/devicetree/bindings/bus/ti-sysc.txt @@ -26,6 +26,8 @@ Required standard properties: or one of the following derivative types for hardware needing special workarounds: + "ti,sysc-omap2-timer" + "ti,sysc-omap4-timer" "ti,sysc-omap3430-sr" "ti,sysc-omap3630-sr" "ti,sysc-omap4-sr" @@ -49,6 +51,26 @@ Required standard properties: Optional properties: +- ti,sysc-mask shall contain mask of supported register bits for the + SYSCONFIG register as documented in the Technical Reference + Manual (TRM) for the interconnect target module + +- ti,sysc-midle list of master idle modes supported by the interconnect + target module as documented in the TRM for SYSCONFIG + register MIDLEMODE bits + +- ti,sysc-sidle list of slave idle modes supported by the interconnect + target module as documented in the TRM for SYSCONFIG + register SIDLEMODE bits + +- ti,sysc-delay-us delay needed after OCP softreset before accssing + SYSCONFIG register again + +- ti,syss-mask optional mask of reset done status bits as described in the + TRM for SYSSTATUS registers, typically 1 with some devices + having separate reset done bits for children like OHCI and + EHCI + - clocks clock specifier for each name in the clock-names as specified in the binding documentation for ti-clkctrl, typically available for all interconnect targets on TI SoCs @@ -61,6 +83,9 @@ Optional properties: - ti,hwmods optional TI interconnect module name to use legacy hwmod platform data +- ti,no-reset-on-init interconnect target module should not be reset at init + +- ti,no-idle-on-init interconnect target module should not be idled at init Example: Single instance of MUSB controller on omap4 using interconnect ranges using offsets from l4_cfg second segment (0x4a000000 + 0x80000 = 0x4a0ab000): @@ -74,6 +99,17 @@ using offsets from l4_cfg second segment (0x4a000000 + 0x80000 = 0x4a0ab000): reg-names = "rev", "sysc", "syss"; clocks = <&l3_init_clkctrl OMAP4_USB_OTG_HS_CLKCTRL 0>; clock-names = "fck"; + ti,sysc-mask = <(SYSC_OMAP2_ENAWAKEUP | + SYSC_OMAP2_SOFTRESET | + SYSC_OMAP2_AUTOIDLE)>; + ti,sysc-midle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>; + ti,sysc-sidle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>, + <SYSC_IDLE_SMART_WKUP>; + ti,syss-mask = <1>; #address-cells = <1>; #size-cells = <1>; ranges = <0 0x2b000 0x1000>; diff --git a/include/dt-bindings/bus/ti-sysc.h b/include/dt-bindings/bus/ti-sysc.h new file mode 100644 --- /dev/null +++ b/include/dt-bindings/bus/ti-sysc.h @@ -0,0 +1,22 @@ +/* TI sysc interconnect target module defines */ + +/* Generic sysc found on omap2 and later, also known as type1 */ +#define SYSC_OMAP2_CLOCKACTIVITY (3 << 8) +#define SYSC_OMAP2_EMUFREE (1 << 5) +#define SYSC_OMAP2_ENAWAKEUP (1 << 2) +#define SYSC_OMAP2_SOFTRESET (1 << 1) +#define SYSC_OMAP2_AUTOIDLE (1 << 0) + +/* Generic sysc found on omap4 and later, also known as type2 */ +#define SYSC_OMAP4_DMADISABLE (1 << 16) +#define SYSC_OMAP4_FREEEMU (1 << 1) /* Also known as EMUFREE */ +#define SYSC_OMAP4_SOFTRESET (1 << 0) + +/* SmartReflex sysc found on 36xx and later */ +#define SYSC_OMAP3_SR_ENAWAKEUP (1 << 26) + +/* SYSCONFIG STANDBYMODE/MIDLEMODE/SIDLEMODE supported by hardware */ +#define SYSC_IDLE_FORCE 0 +#define SYSC_IDLE_NO 1 +#define SYSC_IDLE_SMART 2 +#define SYSC_IDLE_SMART_WKUP 3 -- 2.15.0 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
